Locosys GW-52 User manual
www.
locosystech.com
Quick Start Guide
GW-52
RESET/DOWN
GPS Function
MODE/BA K
Blinking:
searching for GPS
Steady on:
GPS is ready
Alarm status
Battery level
harging
status
ADJUST/ENTER
BA KLIGHT
(in the center of the screen)
START/UP
USB Port
GPS Antenna
www.
locosystech.com
Section 1. Brief Introduction
1.1 Use the cable that comes along in the package to power
on GW-52 and charge it for at least 2 ho rs.
1.2 To ch MODE and select Time modes
(1) Clock; (2) Alarm; (3) Stopwacth; (4) Timer
1.3 To ch both ADJUST key and GPS key sim ltaneo sly to
enter GW-52 setting screen.
1.4 To ch both START key and GPS key to enter GPS mode
screen. Start searching for GPS…
(A to Lock Enabled: If SPD GENIE val e is none-zero)
1.5 START + MODE: Lock/Unlock key.
Center Key: Backlight on last 3 sec.
Battery O tline Flash: Device key lock
www.
locosystech.com
Section 2. Time Mode
2.1
lock Mode
Display local time and be adj sted with GMT setting.
Tip: Q ick clock time set p for first time sage.
(1) GMT Setting: Refer to 3.4
(2) GPS Time Synchronization: Under open sky
environment, switch to "Action Speed" screen and wait
ntil the GPS icon is steady on. It will be synchronized to
the precise GPS time a tomatically.
2.2 Alarm Mode
To ch ADJUST key to adj st alarm time in seq ence.
To ch UP or DOWN key to select n mbers and START
or RESET key to start/close alarm.
2.3 Stopwatch Mode
To ch START key to start co nting time and to ch
again to stop.
To ch RESET key to reset co nting time as
“00:00
00
”.
2.4 Timer Mode
To ch ADJUST key to adj st timer time in seq ence.
To ch UP or DOWN key to select n mbers and MODE
key to complete.
To ch START key to start co nting down and to ch
again to pa se.
To ch RESET key to reset
www.
locosystech.com
Section 3. Setting
3.1
LOGGING: Log rate setting.
To ch ADJUST key to select OFF, 1HZ, 5HZ thro gh UP
or DOWN key. To ch ADJUST key again to complete.
3.2 MIN SPEED: Speed threshold, only speed above [MIN
SPEED] is logged.
To ch ADJUST key to select 0 KMH to 15 KMH thro gh
UP or DOWN key. To ch ADJUST key again to complete.
3.3 UNIT: Speed meas rement nit.
To ch ADJUST key to select KM, MI, NM thro gh UP or
DOWN key. To ch ADJUST key again to complete.
3.4 GMT: Set GMT/Time zone, e.g. +8:00 for Taipei.
To ch ADJUST key to select Time Zone thro gh UP or
DOWN key. To ch ADJUST key again to complete.
(Time display in clock mode)
3.5 SPEED AVG: Time interval for speed averaging.
To ch ADJUST key to select 1 sec to 60 sec thro gh UP
or DOWN key. To ch ADJUST key again to complete.
3.6 SPD GENIE: The minim m speed threshold to activate
[SPD GENIE] f nction.
To ch ADJUST key to select 0 KMH to 31 KMH thro gh
UP or DOWN key. To ch ADJUST key again to complete.
www.
locosystech.com
3.7 A TION SPEED: Speed display type.
To ch ADJUST key to select SPEED(1), NS AVG(2) thro gh
UP or DOWN key. To ch ADJUST key again to complete.
(1)SPEED - C rrent speed
(2)NS AVG - Average speed based on [SPEED AVG].
3.8 SPD FONT: Speed display font.
To ch ADJUST key to select SMALL, BIG thro gh UP or
DOWN key. To ch ADJUST key again to complete.
3.9 FIRMWARE VERSION
To ch ADJUST key to check device info.
Firmware Version: V0.9G326A
User Name: GW31USER
Serial N mber: S000000000
GPS Version: E005
www.
locosystech.com
Section 4. GPS Mode
4.1
Action Speed: Display c rrent instant speed or N-sec.
average speed.
Vertical Bar: Log memory sage.
Horizontal Bar: Speed acc racy indicator.
(Long bar means good signal)
To ch START key to next page “Top 10 AVG Speed”.
4.2 Auto Speed Report: If [SPD GENIE] is enabled, the
a to speed report screen shows at the end of each
session.
e.g. MAX SPEED: 38.26 KH
N-SEC SPEED: 34.41 KH
(Medal icon: New record achieved.)
Small Font
Big Font
www.
locosystech.com
4.3 Top 10 AVG Speeds: Show Top 10 average speed
records.
To ch START key to next page and to ch RESET key
to previo s page.
To ch MODE key to scroll page.
To ch ADJUST key to delete records.
4.4 Top 10 Max Speeds: Show Top 10 max speed record.
To ch START key to next page and to ch RESET key
to previo s page.
To ch MODE key to scroll page.
To ch ADJUST key to delete records.
4.5 PVT: Show position, velocity, and time
To ch START key to next page and back to Action
Speed screen.
To ch RESET key to previo s page.
www.
locosystech.com
Section 5. GW-52 P Utility
5.1 onnect device procedure : (Make sure USB driver is installed)
(1) Select COM port properly.
(2) Click “Connect” to connect device.
Once the device is connected, the firmware version will be displayed.
(“V1.0G1120A” in this example)
5.2 Click
“
Settings
”
to select setting f nction page.
In setting f nction page, sers can change sername, tc offset, log
interval
…
.
www.
locosystech.com
5.3 Click
“
Log Data
”
to select log f nction page.
In this page, sers can download log data (in SBP format).
www.
locosystech.com
5.4 Click “Log Convert” to convert the SBP file into cvs, NMEA, GPX and KML
files.
(If sers want to see the travel trajectory, please check [] Google Earth
View.)
www.
locosystech.com
5.5 Click
“
Browse
”
to view the SBP file.
www.
locosystech.com
5.6 Click the SBP record in the browse page to view the point on Google Map.
Or, to view the converted GPX and KML files on Google Earth.
Other manuals for GW-52
1
Table of contents
Other Locosys GPS manuals
