Logicbus RADIONODE RN400-T2PM User manual

User Manual
PM 2.5 Particulate
Matter Data Logger
RN400-T2PM
2021 | Rev. 1.02 Keep this document nearby so that it may be referred to when needed.

02
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
CONTENTS
Operation
Installation
Introduction
Configuration
About this Manual
08
04
14
19
05
Key Features
Exterior
Accessories
Specifications
Terminal Block
Data Logger Installation
Connecting Terminal Block
Intellectual Property Rights
Notational Conventions
Viewing Channel Information
Viewing Device Information
Resetting Data Logger
Memory Card for Data Logging
Device Information
Server
Measurement
Wi-Fi Network
Display
Commands
Memory Card Usage Configuration
04
04
09
10
12
06
06
07
07
15
16
17
18
21
22
23
24
27
28
29

03
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Check-in
Data-in
Data Logger
Accessories
Cleaning
Batteries
Firmware Update
Manufacturer Contact Information
Warranty
Limit of Liability
Certifications
Adding Devices from Your Smartphone
Adding Devices from Your Computer
Checking Communication With Radionode365 Server
RS-485 Modbus Communication
30
30
38
38
39
46
46
32
35
42
45
40
40
40
41
Order List
Maintenance
Radionode365
HTTP Radionode Protocol V2
Customer Service Information 40
38
46
42
31

04
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
About
this
Manual
©2021DEKISTCo.,Ltd.
AllcontentsandfigureshereinarepropertyofDEKISTCo.,Ltd.
Reproductionorredistributionofallorpartofthisdocumentinany
wayisnotpermittedwithoutpriorconsentfromDEKIST.
Thisdocumentcontainsinstructionsforusageandinstallationof
the RADIONODE® RN400-T2PM. Product specifications and
certain features herein may be subject to change without prior
notice.Figuresusedinthismanualareforexplanatorypurposes
only,and may differ from your system depending on installation
conditions. Software screenshots may change after software
updates.
Notational
Conventions
Intellectual
Property
Rights
Additionalhelpfulinformationismarkedwith"Note".
Failuretofollowinstructionsmarkedwith"Warning"may
resultinslightinjurytotheuser.
Failuretofollowinstructionsmarkedwith"Caution"may
resultinequipmentdamageormalfunction.

05
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Introduction
The RN400-T2PM Data Logge r p er io di ca ll y m ea su re s the
concentration of PM 2.5 partic u l ate matter (also known
as fine dust) in the atmosphere  b y  s ize and sends
measurement data to the Radion o d e 365 server. RN400-
T2PMcomeswithatotalof  s ixI/Ochannels.
Theunitofmeasurementisμg/m³.IfChannel1measurementis
42.75, then particles 0.3  2.5 μm in size in the space of 1
meter³weigh42.75micrograms.
ThePMsizeisacumulativerange.AsasizeofPM10includesthat
of
PM2.5,themeasurementofChannel2isalwaysequaltoor
greater
thanthemeasurementofChannel1.UsetheUACalibratorprogram
toswitchthePMsizefromaccumulativerangetosegmentrange.
FormoreinformationontheUACalibrator,seeRS-485Modbus
Communicationonpage30.
IfChannel6measurementis127,thenthenumberofparticles
biggestinsizeamongotherparticlesinthespaceof1meter³is127.
OnlymeasurementsofChannels1,2and6aredisplayedasdata
intheDataLogger.UseRadionode365toseemeasurementsofall
channels.
Channel1
Channel2
Channel3
Channel4
Channel5
Channel6
AccumulativeRange SegmentRange
0.3μm≤PM2.5≤2.5μm
0.3μm≤PM10≤10μm
0.3μm≤PM0.5≤0.5μm
0.3μm≤PM1.0≤1.0μm
0.3μm≤PM4.0≤4.0μm
Numberofparticleslargest
insize
1.0μm<PM2.5≤2.5μm
4.0μm<PM10≤10μm
0.3μm<PM0.5≤0.5μm
0.5μm<PM1.0≤1.0μm
2.5μm<PM4.0≤4.0μm

06
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Exterior
Key Features KeyfeaturesoftheRN400-T2PMinclude:
UseWi-FiconnectiontoeasilyconfigureyourDataLogger.
MeasurementdatacanbeviewedremotelyfromRadionode365
website.SeeRadionode365onpage31.
MeasurementdatacanbeloggedonamicroSDcard.
ModbusRTU(RS-485)communicationallowsPLCtoaccessData
Logger.
❶  Display ❷  Menu button ❸  Display button ❹  Power
button❺Cablegland
PowercablesandPLCorotherdevicecablesareconnectedviacable
glandstotheinternalterminalblock.
Forinstructionsonhowtousethebuttons,seeOperationonpage
14.
SW
POWER
ON/OFF
●
●
●
●
S W POWER
ON/OF F
2
3
1
5
4

07
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Accessories
Specifications
3.6VBattery DCAdapter(12V,500mA)
Intheeventofpowerfailure,aC-type3.6Vbatterymustbeplaced
in the Data Logger. RADIONODE Data Logger is designed to not
operatewithoutabattery,evenwhenexternalpowerisconnected.
SWPOWER
ON/OFF
165 mm
50 mm
100 mm
115 mm
Wi-Fi
RS485
CableGland
WaterResistance
Rating
ExternalDCPower
Size
OperatingConditions
2.4 GHz IEEE 802.11 b/g/n, WPA2-
EnterpriseModbusRTU
PG-9
IP65
5∼30V(BuiltinUPS)
165×50×115mm
-10~60°C,0~95%RH(non-condensed)

08
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Installation
Thefollowingprocedurewillguidefromtheinstallationprocedureto
theRadionode365registrationprocess.
1.Installsensorsorconnectotherdevices
totheDataLoggeras
needed.
2.Connectpowerandinsertthebattery.
3.UsethevirtualWi-Firouterfeatureto
configuretheDataLogger.
SeeConfigurationonpage19.
4.NowthattheDataLoggerhasbeen
installed,itmustberegistered
toRadionode365.SeeRadionode365onpage31.
Dependingonyourinstallationcircumstancesandconditions,your
installationprocessmayvary.Forexample,ifyouareinstalling
multipleDataLoggers,youmightfinditeasierto:
InsertbatteriesintoallDataLoggersbeforerunning.
ConfigureoneDataLoggerfirst.
UseamicroSDcardtosetupadditionalDataLoggers.Forthis
method,seeMemoryCardUsageConfigurationonpage29.
RegistertheDataLoggersontoRadionode365.
Finally,installtheDataLoggers.
1.
2.
3.
4.
5.

09
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Terminal
Block
Micro SD Card
Slot Fine Dust
Sensor
MicroUSBPort
TempSensor
Terminal
BatteryHolder
PowerOutlet
TerminalBlockscanbefoundinsideofaDataLogger,withother
componentsarrangedasfollows:
MicroSDcardisusedtologmeasurementdata.seeMemoryCard
forDataLoggingonpage18.
ThemicroUSBportisusedforsensorcalibration.AsRN400Series
sensorsareshippedaftercalibration,nofurthercalibrationis
required.However,ifthesensormalfunctions,contactDEKISTfor
inspection.
Formoreinformationontheterminalblock,seeConnecting
TerminalBlockonpage12.
1 2
4
3
5
6
❶
❹
❷
❺
❸
❻

10
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Data Logger
Installation
Loosenthecablegland.
ThegeneralprocedureforinstallingaDataLoggerisasfollows:
Routethecablesofthedevicethatwillbeconnectedthroughthe
glandandconnecttotheterminalblock.Then,connectexternal
DC power and insert the battery. For more information on
terminal block connection, see Connecting Terminal Block on
page12.
Loosenthescrewontherightsideofthefrontpanelandopen
thefrontpanel.
1.
2.
3.
SW
POWER
ON/OFF

11
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
4.
5.
6.
Tightentheglandfirmly.
Coverthefrontpanelandtightenthescrews.
Ifnecessary,usescrewstosecure.Therearethreescrewholeson
thebackofthedevice.
ThereDataLoggerisequippedwithamagnetattherear.Place
theDataLoggeronasteelpanel.
SW
POWER
ON/OFF

12
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Connecting
Terminal
Block
IfnoexternalDCpowerissupplied,theRS485terminal
willnotfunction.
Whenconnectingcablestotheterminalblock,ensure
thattheflatcabledoesnotgetdisconnectedfromthe
frontconnector.
RS485
DC Power ConnectthePowercabletothePOWERterminal.Connectthered
cable to the + terminal, and the remaining cables to the -
terminal.
ConnecttheRS485cabletotheRS485terminal.Connectthecable
linkedtotheAterminaloftheotherdevicetotheAterminal,and
theremainingcablestotheBterminal.
FormoreinformationonhowtochangeModbuscommunication
settings,seeRS-485ModbusCommunicationonpage30.
B A
RS485
B A
RS485
+ -
POWER
5~30V
+ -
POWER
5~30V

13
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Batteries InsertaC-type3.6Vbatteryintothebatteryholder
Be carefulnot toconnectbatterieswithopposite
polarities.Doingsomaydamagethedevice.

14
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Operation
buttonuntil
appears.Holdthe buttonagain.
:Pressthe button.
Whenthedataloggeristurnedon,themodelnumberandotherkey
information is displayed with the corresponding measurements. If
no external power is supplied, the display will turn off shortly and
theDataLoggerwillentersleepmode.
ViewingChannelInformation:Toviewchannelinformation,
including measurements on sleep mode, press the button.
Press the button repeatedly to display different status
information.
SelectingaMenu:Pressthebutton,thenpressthebutton.
Pressthebuttonrepeatedlytodisplaydifferentmenuitems.
Pressthebuttontoopenthedisplayedmenu.Pressthe
buttontoexitthemenu.
TurningDataLoggerOff:Pressthebuttonandholdthe
PRESS 'P' ONE MORE TO POWER IT OFF
S W POWER
ON/OF F
●
●
●
● TurningDataLoggerOn

15
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Viewing
Channel
Information
Currentdateandtime
Wi-Fi network name and
signalstrength
MeasurementofChannel6
(number of particles
largestinsize)
[ONLY RN400-T2GS]
Displays the temperature
value of the chemical cell
insidetheproduct.
Elapsed time since last
transfer of measurement
data to the server &
number of datasets to
transferinthenextcycle
Press the button repeatedly to display the below channel data. A
sensorchannelthatisnotconnectedwillappearas(none).
MeasurementofChannel
LAST SENSING |S:menu 1(concentrationofPM2.5
PM2.5 18.87 ug/m3
particle)
Measurement of Channel 2
(concentrationofPM10
particles)
Typeofbatteryinsertedand
current voltage. If the
voltage is low, LOW will be
displayed.
You can select the level
of the digital filter. The
higher the number, the
less sensitive the
sensor reacts (1 level:
highest sensitive, 15
level: lowest sensitive).
You can choose from
thesettingsmenu.
LOCAL TIME |S:menu
2020-11-30 17:00
WIFI SSID dB|S:menu
xxxxxxxx, -50dB
DATA FILTER.|S:menu
SLOW LEVEL(1-15):1
LAST SENSING |S:menu
PM10 20.01 ug/m3
LAST SENSING |S:menu
PM0.5 127.36 #/m3
LAST TRANSMIT|S:menu 5
Min Ago, 9 smpl
BATTERY STAT.|S:menu
OK. |1.5Vx2|2.88V
GS CELL TEMP.|S:menu
CELL Temp: 22 C

16
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Viewing
Device
Information
GatewayIPaddress
Measurementinterval
DataLoggerIPAddress
Radionode365accountID
(numberofdatasetstosend=TransferInterval÷Measurement
Interval)
Whenmeasurementintervalissetto5minutesandthetransfer
intervalsetto20minutes,4datasetsaresaveduntilthe
nexttransfer.Ifdatatransferfails,datasetsaccumulateuntil
successful.
To view device information, select 1.VIEW INFO. To view the next
item,pressthebutton.Toexit,pressthebutton.
Numberofdatasetstosend
INFO|S:next, P:exit totheserverinthenext
1.HOLDING DATA: 4
cycle.
T i m e  e l a p s e d  s i n c e
l a s t  t r a n s m i s s i o n  o f
m e a s u r e m e n t  d a t a  t o
s e r v e r
If no external power is
connected or power failure
occurs,Batwillappear.
Measurement data
transmission to server
interval
INFO|S:next, P:exit
3.SENSING: 1 Min
INFO|S:next, P:exit
4.SENDING: 5 Min
INFO|S:next, P:exit
5.UPDATE: 1 Min Ago
INFO|S:next, P:exit 6.ID:
xxxxxxxx
INFO|S:next, P:exit
7.IP:192.168.10.13
INFO|S:next, P:exit
8.GW:192.168.1.1
INFO|S:next, P:exit
2.POWER: External DC

17
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
INFO|S:next, P:exit
9.DN:210.220.163.82
INFO|S:next, P:exit
10.MAC:508CB16FA1B3
INFO|S:next, P:exit
12.MODEL:RN400T2PM
INFO|S:next, P:exit
13.CAL:2020-12-25
INFO|S:next, P:exit
14.MODE: ug/m3,CUM
INFO|S:next, P:exit
11.SW BUILD:20200720
ModelNo.
Firmwareversion
DNSserverIPaddress
Dateofsensorcalibration
DataLoggerMACaddress
Measurementunitandtype
ofPMrange.
CUMisthecumulative
range.
Allsettingoptions(exceptforWi-Finetwork)canbereset.Select
4.FACTORY DEFAULT.
Resetting
Data Logger

18
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Memory
Card for Data
Logging
OpenthefrontoftheDataLoggerandinsertamicroSDcardinto
thecardslotinsidethefrontpanel.
IfamemorycardisinstalledintheDataLogger,measurementdata
willbewrittentothememorycardasaCSVfileasfollows:
Measurementdate,timestamp,MACaddress,valuefor
Channel1,...,valueforChannel6
UseanSDcard(upto16GB)formattedwiththeFAT32
filesystem.Otherfilesystemsarenotsupported.

19
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
Configuration
Onyoursmartphone,findtheWi-Finetworkwiththesamename
asshownonthedisplayandconnecttothenetwork.
TheDataLoggerisequippedwithavirtualWi-Firouter.Thevirtual
router allows your smartphone or tablet to be linked to Data
Loggerforconfiguration.
Select 2.CONFIG MODE(AP) to enable the virtual router. The
followingwillappearinthedisplay:
Depending on the version of your Android phone, user
identification may be required, as Data Logger is not
connectedtotheInternet.
1.
2.
SOFTAP: _RN400-
A1B3 ACCESS:
192.168.1.1
Multiplemobiledevicescannotbeconnectedtothe
DataLoggeratthesametime.

20
Order List
About this Manual Introduction Installation Operation Configuration Radionode365 Maintenance Customer Service
Information
HTTP Radionode Protocol V2
3.
4.
5.
Changethesettingsoneachpage,thentap
Tofinishconfiguration,tapReboot.
Openyoursmartphone’swebbrowserandtype
intheaddressbar.TheSettingspagewiillappear.
"192.168.1.1"
Save.