Logicube echo plus User manual

Echo Plus Users Manual i
Echo Plus™ User’s Manual
Logicube, Inc.
Chatsworth, CA 91311
818 700 8488
www.logicube.com
Version: 2.9
MAN-Echo Plus
Date: 02/05/15

Echo Plus Users Manual ii
Table of Contents
ECHO PLUS™ USER’S MANUAL.............................................................I
TABLE OF CONTENTS.............................................................................II
Logicube Technical Support Contact Information ..Error! Bookmark
not defined.
1. INTRODUCTION TO THE LOGICUBE ECHO PLUS............................4
Introduction ......................................................................................... 4
System Description......................................................................... 4
2. GETTING STARTED .............................................................................1
Connecting Drives to the Logicube Echo Plus................................ 1
IDE Drive Installation...................................................................... 1
SATA Drive Installation................................................................... 2
Echo Plus Overview............................................................................ 3
Operation Buttons........................................................................... 4
3. CLONING MODES AND SETTINGS....................................................5
User Interface ...................................................................................... 5
Main Screen.................................................................................... 5
About Screen.................................................................................. 5
Using the Settings Menu................................................................. 6
Copy Modes.................................................................................... 6
CleverCopy Mode........................................................................... 6
Mirror Mode .................................................................................... 6
CHS Mode ...................................................................................... 7
Verify............................................................................................... 8
Speed Setting ................................................................................. 8
Cloning Screens ............................................................................. 9
Preview Screen............................................................................... 9
Progress Screen........................................................................... 10
End of the Cloning Session .......................................................... 10
Cloning Windows 7....................................................................... 10
Cloning Windows Vista................................................................. 11

Echo Plus Users Manual iii
Vista Installations.......................................................................... 11
Cloning Scenarios and how to handle them................................. 11
A Simple Vista partition with logical drivers.................................. 11
Hidden RE (Recovery Environment) Partition with Vista.............. 11
Other VISTA Scenarios ............................................................... 11
4. SOFTWARE LOADING INSTRUCTIONS ...........................................13
Logicube Echo Plus Software Updating Procedures.................... 13
Important Notes Regarding Software Versions............................ 13
Software Loading.......................................................................... 13
Installing the VCP Controller Software and drivers ...................... 13
Attaching the Echo Plus to the PC ............................................... 14
Determining the COM Port for the Echo Plus............................... 15
Configuring Hyperterminal or other third party terminal program
and installing the software............................................................ 16
5. FREQUENTLY ASKED QUESTIONS AND ANSWERS .....................18
FAQ’s.................................................................................................. 18
Advanced Topics............................................................................... 21
SID changing issues..................................................................... 21
6. INDEX..................................................................................................23

Echo Plus™ Users Manual
1
Limitation of Liability and Warranty Information
Logicube Disclaimer
LOGICUBE IS NOT LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING,
BUT NOT LIMITED TO PROPERTY DAMAGE, LOSS OF TIME OR DATA FROM USE OF A LOGICUBE
PRODUCT, OR ANY OTHER DAMAGES RESULTING FROM PRODUCT MALFUNCTION OR FAILURE
OF (INCLUDING WITHOUT LIMITATION, THOSE RESULTING FROM: (1) RELIANCE ON THE
MATERIALS PRESENTED, (2) COSTS OF REPLACEMENT GOODS, (3) LOSS OF USE, DATA OR
PROFITS, (4) DELAYS OR BUSINESS INTERRUPTIONS, (5) AND ANY THEORY OF LIABILITY, ARISING
OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE (OR FROM DELAYS IN SERVICING
OR INABILITY TO RENDER SERVICE ON ANY) LOGICUBE PRODUCT.
LOGICUBE MAKES EVERY EFFORT TO ENSURE PROPER OPERATION OF ALL PRODUCTS.
HOWEVER, THE CUSTOMER IS RESPONSIBLE TO VERIFY THAT THE OUTPUT OF LOGICUBE
PRODUCT MEETS THE CUSTOMER’S QUALITY REQUIREMENT. THE CUSTOMER FURTHER
ACKNOWLEDGES THAT IMPROPER OPERATION OF LOGICUBE PRODUCT AND/OR SOFTWARE, OR
HARDWARE PROBLEMS, CAN CAUSE LOSS OF DATA, DEFECTIVE FORMATTING, OR DATA
LOADING. LOGICUBE WILL MAKE EFFORTS TO SOLVE OR REPAIR ANY PROBLEMS IDENTIFIED BY
CUSTOMER, EITHER UNDER WARRANTY OR ON A TIME AND MATERIALS BASIS.
Warranty
DISCLAIMER
IMPORTANT - PLEASE READ THE TERMS OF THIS AGREEMENT CAREFULLY. BY INSTALLING OR USING
LOGICUBE PRODUCTS, YOU AGREE TO BE BOUND BY THIS AGREEMENT.
IN NO EVENT WILL LOGICUBE BE LIABLE (WHETHER UNDER THIS AGREEMENT, RESULTING FROM THE
PERFORMANCE OR USE OF LOGICUBE PRODUCTS, OR OTHERWISE) FOR ANY AMOUNTS REPRESENTING
LOSS OF PROFITS, LOSS OR INACCURACY OF DATA, LOSS OR DELAYS OF BUSINESS, LOSS OF TIME, COSTS
OF PROCUREMENT OF SUBSTITUTE GOODS, SERVICES, OR TECHNOLOGY, PROPERTY DAMAGE, OR
INDIRECT, CONSEQUENTIAL, OR PUNITIVE DAMAGES OF A PURCHASER OR USER OF LOGICUBE PRODUCTS
OR ANY THIRD PARTY. LOGICUBE’S AGGREGATE LIABILITY IN CONTRACT, TORT, OR OTHERWISE
(WHETHER UNDER THIS AGREEMENT, RESULTING FROM THE PERFORMANCE OR USE OF LOGICUBE

INTRODUCTION
Echo Plus Users Manual 2
PRODUCTS, OR OTHERWISE) TO A PURCHASER OR USER OF LOGICUBE PRODUCTS SHALL BE LIMITED TO
THE AMOUNT PAID BY THE PURCHASER FOR THE LOGICUBE PRODUCT. THIS LIMITATION OF LIABILITY
WILL BE EFFECTIVE EVEN IF LOGICUBE HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH DAMAGES.
LOGICUBE MAKES EVERY EFFORT TO ENSURE PROPER OPERATION OF ITS PRODUCTS. HOWEVER, THE
PURCHASER IS RESPONSIBLE FOR VERIFYING THAT THE OUTPUT OF A LOGICUBE PRODUCT MEETS THE
PURCHASER’S REQUIREMENTS. THE PURCHASER FURTHER ACKNOWLEDGES THAT IMPROPER OPERATION
OF LOGICUBE PRODUCTS CAN CAUSE LOSS OF DATA, DEFECTIVE FORMATTING, OR DEFECTIVE DATA
LOADING. LOGICUBE WILL MAKE EFFORTS TO SOLVE OR REPAIR ANY PROBLEMS IDENTIFIED BY
PURCHASER, EITHER UNDER THE WARRANTY SET FORTH BELOW OR ON A TIME AND MATERIALS BASIS.
LIMITED WARRANTY
FOR ONE YEAR FROM THE DATE OF SALE (THE “WARRANTY PERIOD”) LOGICUBE WARRANTS THAT THE
PRODUCT (EXCLUDING CABLES, ADAPTERS, AND OTHER “CONSUMABLE” ITEMS) IS FREE FROM
MANUFACTURING DEFECTS IN MATERIAL AND WORKMANSHIP. THIS LIMITED WARRANTY COVERS
DEFECTS ENCOUNTERED IN THE NORMAL USE OF THE PRODUCT DURING THE WARRANTY PERIOD AND
DOES NOT APPLY TO: PRODUCTS DAMAGED DUE TO PHYSICAL ABUSE, MISHANDLING, ACCIDENT,
NEGLIGENCE, OR FAILURE TO FOLLOW ALL OPERATING INSTRUCTIONS CONTAINED IN THE OPERATING
MANUAL; PRODUCTS WHICH ARE MODIFIED; PRODUCTS WHICH ARE USED IN ANY MANNER OTHER THAN
THE MANNER FOR WHICH THEY WERE INTENDED, AS SET FORTH IN THE OPERATING MANUAL; PRODUCTS
WHICH ARE DAMAGED OR DEFECTS CAUSED BY THE USE OF UNAUTHORIZED PARTS OR BY
UNAUTHORIZED SERVICE; PRODUCTS DAMAGED DUE TO UNSUITABLE OPERATING OR PHYSICAL
CONDITIONS DIFFERING FROM THOSE RECOMMENDED IN THE OPERATING MANUAL OR PRODUCT
SPECIFICATIONS PROVIDED BY LOGICUBE; ANY PRODUCT WHICH HAS HAD ANY OF ITS SERIAL NUMBERS
ALTERED OR REMOVED; OR ANY PRODUCT DAMAGED DUE TO IMPROPER PACKAGING OF THE WARRANTY
RETURN TO LOGICUBE. AT LOGICUBE’S OPTION, ANY PRODUCT PROVEN TO BE DEFECTIVE WITHIN THE
WARRANTY PERIOD WILL EITHER BE REPAIRED OR REPLACED USING NEW OR REFURBISHED
COMPONENTS AT NO COST. THIS WARRANTY IS THE SOLE AND EXCLUSIVE REMEDY FOR DEFECTIVE
PRODUCTS. IF A PRODUCT IS HAS BECOME OBSOLETE OR IS NO LONGER SUPPORTED BY LOGICUBE THE
PRODUCT MAY BE REPLACED WITH AN EQUIVALENT OR SUCCESSOR PRODUCT AT LOGICUBE’S
DISCRETION. THIS WARRANTY EXTENDS ONLY TO THE END PURCHASER OF LOGICUBE PRODUCTS. THIS
WARRANTY DOES NOT APPLY TO, AND IS NOT FOR THE BENEFIT OF, RESELLERS OR DISTRIBUTORS OF
LOGICUBE PRODUCTS. UNLESS OTHERWISE AGREED IN WRITING BY LOGICUBE, NO WARRANTY IS
PROVIDED TO RESELLERS OR DISTRIBUTORS OF LOGICUBE PRODUCTS.
IN ORDER TO RECEIVE WARRANTY SERVICES CONTACT LOGICUBE’S TECHNICAL SUPPORT DEPARTMENT
VIA PHONE OR E-MAIL. PRODUCTS RETURNED TO LOGICUBE FOR REPAIR UNDER WARRANTY MUST
REFERENCE A LOGICUBE RETURN MATERIAL AUTHORIZATION NUMBER (“RMA”). ANY PRODUCT RECEIVED
BY LOGICUBE WITHOUT AN RMA# WILL BE REFUSED AND RETURNED TO PURCHASER. THE PURCHASER
MUST CONTACT LOGICUBE’S TECHNICAL SUPPORT DEPARTMENT VIA E-MAIL
([e-mail]) OR VIA PHONE AT [phone] OPT. 3 TO OBTAIN A VALID RMA#. THE
PURCHASER MAY BE REQUIRED TO PERFORM CERTAIN DIAGNOSTIC TESTS ON A PRODUCT PRIOR TO
LOGICUBE ISSUING AN RMA#. THE PURCHASER MUST PROVIDE THE PRODUCT MODEL, SERIAL NUMBER,
PURCHASER NAME AND ADDRESS, EMAIL ADDRESS AND A DESCRIPTION OF THE PROBLEM WITH AS
MUCH DETAIL AS POSSIBLE. AT LOGICUBE’S SOLE AND ABSOLUTE DISCRETION, REASONABLE TELEPHONE
AND EMAIL SUPPORT MAY ALSO BE AVAILABLE FOR THE LIFE OF THE PRODUCT AS DEFINED BY LOGICUBE.

Echo Plus™ Users Manual
3
EXCEPT AS OTHERWISE SPECIFICALLY PROVIDED IN THIS AGREEMENT, LOGICUBE PRODUCTS ARE
PROVIDED AS-IS AND AS-AVAILABLE, AND LOGICUBE DISCLAIMS ANY AND ALL OTHER WARRANTIES
(WHETHER EXPRESS, IMPLIED, OR STATUTORY) INCLUDING, WITHOUT LIMITATION, ANY WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT OF THIRD PARTY
RIGHTS.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE
ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION.
RoHS Certificate of Compliance
LOGICUBE PRODUCTS COMPLY WITH THE EUROPEAN UNION RESTRICTION OF THE USE OF
CERTAIN HAZARDOUS SUBSTANCES IN ELECTRONIC EQUIPMENT, ROHS DIRECTIVE (2002/95/EC).
THE ROHS DIRECTIVE PROHIBITS THE SALE OF CERTAIN ELECTRONIC EQUIPMENT CONTAINING
SOME HAZARDOUS SUBSTANCES SUCH AS MERCURY, LEAD, CADMIUM, HEXAVALENT
CHROMIUM AND CERTAIN FLAME-RETARDANTS IN THE EUROPEAN UNION. THIS DIRECTIVE
APPLIES TO ELECTRONIC PRODUCTS PLACED ON THE EU MARKET AFTER JULY 1, 2006.
Logicube Technical Support Contact Information
1. By website: www.logicube.com
2. By email: [e-mail]
3. By telephone: 1 - [phone] ext. 3 between the hours of 7am –5pm PST, Monday
through Friday, excluding U.S. legal holidays.

INTRODUCTION
Echo Plus Users Manual 4
1. Introduction to the Logicube Echo Plus
Introduction
Thank you for buying the Logicube Echo Plus. You
are now the proud owner of a state-of-the-art IDE
and SATA disk cloning device. The Echo Plus is
designed to be easy enough to be used by a
novice, yet offers many professional features that
are not available anywhere else.
The Echo Plus copies the contents of one hard disk
drive to another. The first drive is typically called the
Master, while the second is termed a Target. It
performs the copy at speeds that are typically 32 to
64 times faster than they would be on a PC. The
Echo Plus first analyzes the partitions on the
Master, then acts according to a user set mode.
Depending on the mode, the unit will adjust
structures to ensure the validity of the Target. This
process is often called disk cloning.
Both the Master and Target drives connect directly
to the Echo Plus thorugh the IDE or SATA ports,
providing the fastest data path possible
System Description
In the box you will find the following items:
The Echo Plus unit
An external power supply
Two 40-pin flat UDMA cables (5”long). These
connect to Master and Target drives
Two power cables (5”long). These supply power
to the drives
Two 9” SATA (Serial-ATA) cables. These connect
SATA drives to the unit
A “Mini-B” USB cable - Used to update the unit’s
embedded software
A software CD-ROM that includes a copy of the
manual in .PDF format

Echo Plus™ Users Manual
5
A nylon carrying case
If any of the above is missing, please call Logicube
(818 700-8488 x3) immediately and replacement
parts will be shipped to you right away.

Echo Plus™ Users Manual
1
2. Getting Started
Connecting Drives to the Logicube Echo Plus
IDE Drive Installation
.
Figure 1. IDE connections.
1. Lay the unit on a flat non-conductive surface. Note
the connectors on the left and right of the unit. The
Master drive always connects to the left side, while
the Target is connnected to the right side. (Arrows
on the unit’s case show the direction of data flow).
2. Plug one of the 5 inch UDMA cables into the 40- pin
IDE connector on the left, the cable is clearly
marked as to which side plugs into the duplicator.
Plug one of the 5” power cables to the power
receptacle. Make sure that the clip on the 4-pin
plug lines up with the small tab on the socket.
IMPORTANT NOTE: The hard drives are not
powered until you actually start a copy
operation. Connect the Master drive to the
UDMA and power cables.
IMPORTANT NOTE: The supplied cables are
NOT standard IDE cables like the ones found in
a PC. Do not attempt to use these cables in a PC
nor to use PC cables with the Echo Plus unit.
Although damage to the drive is unlikely, the
Echo Plus will not function correctly.

GETTING STARTED
Echo Plus Users Manual 2
4. Connect the other set of UDMA/power cables to the
connectors on the right side of the unit following the
same information as step 2.
5. You may now connect a Target drive to these
cables. Target drives can either be placed on a
suitable surface (non-conductive, or antistatic) or be
left inside an open-cover PC.
NOTE: Make sure that the Master and Target
drives are jumpered as Single Master.
NOTE: Please call Logicube to acquire longer data
and power cables, if needed.
SATA Drive Installation
Please refer to Fig. 2 below.
Figure 2. SATA connections
1. Lay the unit on a flat non-conductive surface. Note
the connectors on the left and right of the unit. The
Master drive always connects to the left side, while
the Target connected to the right side. (Arrows on
the unit’s case show the direction of data flow).
2. Plug one of the SATA cables into the SATA and
power connectors on the left. Make sure that the
clip on the 4-pin power plug lines up with the small
tab on the socket.
NOTE: The power outlet is not powered until you
actually start a copy operation.
3. Connect the Master drive to the SATA cable.
IMPORTANT NOTE: The supplied cables are
NOT standard SATA cables like the ones found
in a PC. Do not attempt to use these cables in a
PC nor to use PC cables with the Echo Plus
unit. Although damage to the drive is unlikely,
the Echo Plus will not function correctly.
NOTE: Jumper settings do not need to be changed
on SATA drives.

Echo Plus™ Users Manual
3
4. Connect the other SATA cable to the connectors on
the right side of the unit following the same
information as step 2.
5. You may now connect a Target drive to this cable.
Target drives can either be placed on a suitable
surface (non-conductive, or antistatic) or be left
inside an open-cover PC.
NOTE: Jumper settings do not need to be changed
on SATA drives.
Things to remember:
The Echo Plus unit (but not the drives) is
powered by connecting the external power
supply to the power input at the top. There is no
On/Off switch. When requested to power-cycle
the unit, please pull the plug, wait a couple of
seconds and push it in again. The unit boots
and is ready to use in about 3 seconds. Wait
for the Main Screen to appear.
The Echo Plus supplies power to both drives
during a cloning session. There is no need to
connect an external power source to the drives.
It is OK to connect and disconnect Master or
Target drives while the Echo Plus is powered.
However, do NOT connect or disconnect drives
in the middle of a cloning session. The Status
light will typically blink to indicate the unit is
cloning.
Echo Plus Overview
Figure 3. Echo Plus

GETTING STARTED
Echo Plus Users Manual 4
Operation Buttons
START/STOP Button –Press it twice to begin a
cloning operation using the current settings; press
the START/STOP button in mid process to abort it.
A single key stroke presents a preview screen
where you can see the current setting, and decide
whether to press it again to begin the capture, or
back out to reconfigure.
SET Button –This button brings you to the settings
screen where you can change capture modes and
other settings of the unit.BACK Button –This
button allows you to go back in the menu system or
cancel out of a given operation.
SELECT Button –This button allows you to select
an option, scroll through multiple available options
or select a sub-menu.
In addition to the buttons there are also three
indicator lights:
POWER Light –This stays lit whenever power is
applied to the Echo Plus unit.
STATUS Light –This blinks during a cloning
session to show that the clone is running.
ERROR Light –This lights up whenever the cloning
session is stopped prematurely. An error
message will appear on the display.

CLONING MODES AND SETTINGS
Echo Plus™ Users Manual
5
3. Cloning Modes and Settings
User Interface
Main Screen
The Echo Plus boots to this screen. It shows the
software version currently loaded on the unit. After
thirty seconds, a Screen Saver will appear. Press
any button to go back to the screen.
About Screen
Press the Back button to go into the About Screen.
This is where the unit’s Firmware version appears
as well as Logicube’s website information. Press
the Back button again to go back to the Main
Screen.
NOTE: The firmware version displayed on your
Logicube Echo Plus may be different than the
picture above.

CLONING MODES AND SETTINGS
Echo Plus Users Manual 6
Using the Settings Menu
Pressing the Set button repeatedly will allow you to
scroll through the Echo Plus Settings. Here they
are in order:
Copy Modes
The Echo Plus has two major cloning modes;
CleverCopy and Mirror Copy.
CleverCopy Mode
This is the default mode. It clones ALL partitions on
the Master drive to the Target drive, automatically
deciding the fastest method possible for each
partition found. It scales certain partitions (FAT16/
32, and NTFS) to fill the Target in its entirety and
makes all the necessary adjustments to ensure a
valid and bootable Target drive.
If an unknown partition is encountered on the
Master during the copy session, that partition
retains its original size.
Mirror Mode
It simply makes a mirror copy of the Master drive. It
does not adjust any values. This mode is
recommended when all else fails an even then only
between similar geometry drives. It is also used for
unknown partition types (i.e. UNIX, LINUX, etc). If
the Target is larger than the Master, the session will
complete when the last sector of the Master is
reached. If the Master is larger, the unit will
complete when reaching the last Target sector.
NOTE: Although the subsequent setting screens
come up and can be changed, they are irrelevant
for Mirror Clone and ignored during the cloning
session.
NOTE: Some PC manufacturers will place a
“hidden” partition on the drive. This partition usually
contains recovery or diagnostic information. The
Echo Plus will automatically Mirror Clone any
hidden partitions.

CLONING MODES AND SETTINGS
Echo Plus™ Users Manual
7
Press the Select button to cycle between the two
modes. Press the Set button to go to the next
screen.
CHS Mode
CHS Mode sets the geometry (Cylinder, Head and
Sector) translation used on the Target drive. CHS
information is stored in the partition table of the
hard drive and is used by the BIOS to determine
from which partition to boot.
The correct setting will depend upon the capacity of
the Target drive and on the BIOS of the PC in which
it will be used. Check with the hard drive and PC
manufacturer to determine which CHS mode is best
as different BIOS systems use different translation
methods for large (over 528 MB) capacity drives.
Following are the CHS modes supported by the
Echo Plus™:
LBA (Default) –This CHS Mode will work for most
hard drive and PC combinations and should be
used unless otherwise indicated.
Large –Also known as Extended CHS (ECHS)
mode.
LBA-1, LBA-2, Large-1 and Large-2 –These
settings instruct the Echo Plus to “shave off” one or
two cylinders from the total drive size when
constructing the Target partition tables.
NOTE: It is important to use -1 or -2 settings for all
Windows 2000 and Windows XP installations.
These operating systems use the unallocated
space to store certain tables required for Active
Directory and sometimes for Dynamic Partitioning.
NOTE: Most of the time, blocking out one cylinder
is enough but two may need to be blocked out to
achieve good results.
Press the Select button to cycle between the two
modes. Press the Set button to go to the next
screen.

CLONING MODES AND SETTINGS
Echo Plus Users Manual 8
Verify
Both CleverCopy and Mirror will allow you to set the
Verify option. If Verify is set to Yes, the Echo Plus
can detect bad sectors on the Target. Data cloned
onto such sectors may be unreadable. Engaging
the verification feature slows the speed of cloning
by a small amount.
If a bad sector is detected on the Target (with Verify
turned on), the cloning process will abort with an
error message. Logicube recommends not using
that drive as new defects are likely to develop.
NOTE: The Echo Plus always checks the Master
drive for bad sectors during a cloning session. It is
designed to skip any bad sectors that are found.
The unit will skip up to 200 bad sectors before it
stops with an error message.
Press the Select button to cycle between the two
modes. Press the Set button to go to the next
screen.
Speed Setting
The speed setting provides the option to set the
speed at which an operation will be performed at.
UDMA-4 - The software performs a test procedure
to determine the fastest setting that the drives will
tolerate while streaming data from one to the other.
When set to UDMA-4, all lower speed grades will
be tested (UDMA 0-4, PIO 0-4).

CLONING MODES AND SETTINGS
Echo Plus™ Users Manual
9
UDMA-3 - Force the unit to use at most this speed.
Set the unit to this mode in some rare situations
where one or both drives do not support the higher
speeds, and “misbehave” during automatic speed
benchmarking.
UDMA-2 - Same as UDMA-3.
UDMA-1 - Same as UDMA-3.
UDMA-0 - Same as UDMA-3.
PIO-Auto (PIO-4) –Force the unit to use this as the
highest speed (PIO-4). Set the unit to this mode in
some rare situations where one or both drives do
not support higher speeds, and “misbehave” during
speed benchmarking.
PIO-Medium –This is a fixed value that almost all
drives will tolerate. It will result in copying speeds
from about 200 to over 500 MB per minute
depending upon the characteristics of the drives.
PIO-Slow –This is a speed value that all drives will
be able to tolerate. It supports copying speeds from
100 to over 300 MB per minute depending on the
characteristics of the drives.
NOTE: Use the MEDIUM or SLOW modes if you
encounter drive “time-outs” or if you are cloning
older drives. Many 2.5” notebook drives require this
setting.
When multiple copies are required, all you need to
do is change the TARGET drive, and press the
Start/Stop button. Your last selections are used.
Cloning Screens
Preview Screen
Once the desired settings are in place, press the
Start/Stop button once to enter the Preview
Screen. This screen displays the chosen settings.
Press the Back button to go back to the Main

CLONING MODES AND SETTINGS
Echo Plus Users Manual 10
Screen, the Set button to go to the Settings or the
Start/Stop button to begin cloning.
Progress Screen
This screen is displayed during the cloning session
itself. It shows the speed (in GB/min), time
remaining and percentage of drive cloned.
End of the Cloning Session
When the Echo Plus is finished with a successful
Clever or Mirror cloning session, the drives will turn
off and a “clone successful” message will appear on
the display. At this point the drives can be
removed.
If the unit stops prematurely with an error, the error
message will display instead.
Cloning Windows 7
With the release of the Windows 7 Operating
System, Microsoft has added some security
features to protect the integrity of the partition.
These features can cause problems when cloning
Windows 7 with Clever Clone mode.
This section will discuss the best ways to clone
Windows 7 hard drives.
SCENARIO 1: When the Master and Target
drives are the same size
With this scenario, you can use Clever Copy mode
to clone the Windows 7 hard drive. Since the
Master and Target drives are the same size, the
size of the partitions should remain the same.
SCENARIO 2: When the Master and Target
drives are different sizes
With this scenario, you must use Mirror mode to
clone the Windows 7 hard drive. The Logicube
Echo Plus is unable to Clever Copy Windows 7
drives if the Master and Target drives are different
sizes.