Addonics Technologies HDUSAS User manual

Technical Support
If you need any assistance to get your unit functioning properly, please have your
product information ready and contact Addonics Technical Support at:
Hours: 8:30 am - 6:00 pm PST
Phone: [phone]
Email: http://www.addonics.com/support/query/
v3.1.11
User Guide
1:1 Duplicator
(HDUSAS)
T E C H N O L O G I E S
www.addonics.com
ENT
ESC

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
ENT
ESC
Diagram
ENT
ESC
Duplicator Panel
LCD
Scroll Up
Scroll Down
Executes Function
Cancels Function
Source
SATA Port
4-pin Floppy Power
Connector
Destination
SATA Port
Mounting Holes
(2 on each side)

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
Quick Guide
Installing the 1:1 duplicator
Step 1
Insert the 1:1 duplicator into standard 5.25” drive bay.
Step 2
Connect the power cable from you system to the 4-pin floppy power connector.
Step 3
Connect the source drive to the source SATA port via SATA cable and the target
drives to the destination SATA port via SATA cable.
Step 4
Screw the duplicator into the drive bay with 4 screws (2 on each side).
Duplicating drive(s)
Make sure the source and target drives are connected to the proper ports.
When the duplicator is on, it will go through the steps below.
Step 1
Duplicator LED will light up and the device will beep.
Step 2
LCD will display initial steps:
1. Duplicator Ver: - Displays duplicator version
2. Initializing SDRAM
3. Detect Source/Target - Will detect the type of source/targets
4. Copy - Defaults to the first function which is to copy
Step 3
Once the duplicator gets to the copy menu, press ENT to begin copying. The
duplicator will auto-detect the drive and display its information on the LCD. Make
sure that the power LEDs of the flash reader are blinking, the blinking indicates
drive activity.
You can find the complete user manual of the 1:1 Duplicator panel on the driver
disk under user guides. You can also download it from our website at
www.addonics.com/support/user_guides/

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
ENT
ESC
Duplicator Panel
LCD
Scroll Up
Scroll Down
Executes Function
Cancels Function
The Duplicator has 6 functions to choose from:
1. Copy
2. Compare
3. PreScan Source
4. ReScan BUS
5. Source Size
6. Setup
7. USB Mode
6-1. Language
6-2. Copy Size
6-3. Startup Menu
6-4. Auto Compare
6-5. Copy with Size
6-6. Button Sound
6-7. Device Info
6-8. System Info
Within function 6, there are 8 Subfunctions

1. Copy
Make sure that the capacity of the target is equal or larger than the source.
Copies data directly from the source to the target.
Choose option 1 from the menu and press ENT to begin copying. The system will
auto detect the source/target and display info about the copying process. Once
the copying process is complete, the LCD will display Copy OK.
2. Compare
Compare is used to see if the data on the source is identical to the target after the
copy operation.
Choose option 2 and press ENT to begin comparison. The LCD will display
comparison progress info and once complete will display information about how
many comparisons were OK, how many failed and how many were different.
3. PreScan Source
PreScan is used to check if the source can be accessed properly. It also tests the
read speed of the source.
Choose option 3 and press ENT to begin scanning. The LCD will display scan
progress info and read speed. Once the scan is complete, the LCD will display
PreScan Ok.
4. ReScan Bus
ReScan Bus allows swapping the source or target in and out without having to
reboot the system.
Choose option 4 and press ENT to begin rescanning. The system will rescan the
source without the need to reboot.
5. Source Size
Source Size is used to show the capacity of the source.
Choose option 5 and press ENT. The LCD will display the capacity of the source.
6. Setup
Setup allows various system settings to be changed. There are 8 sub-options:
Language, Copy Size, Startup Menu, Auto Compare, Copy with Size, Button
Sound, Device Info and System Info.
Choose option 6 and the LCD will display the first option of the subfunctions.
www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
Setup Functions
6-1. Language
Use this option to select the language of the system, by default it’s set at English.
6-2. Copy Size
This option is used to specify the size of the source for simplifying further copying
operations.
Press ENT on this option and the LCD will display Copy Size ALL. Use the up
and down arrow keys to change the copy size. The system will offer
corresponding percentages so the user can specify the amount to copy from the
source.
6-3. Startup Menu
This option allows the user to change the first option they see when they boot up
the system. By default, the first option is Copy.
To change this, press ENT and use the up and down arrows to choose other
options.
6-4. Auto Compare
This option toggles the systems ability to automatically compare the source and
target after a copy is complete.
By default it is set to OFF, use the up and down arrows to toggle between ON
and OFF.
6-5. Copy with Size
This option is used to make the capacity of the target hard drive the same as teh
source hard drive.
For example, you have a target hard drive with 250GB capacity and a source
hard drive with 80GB capacity. After the copying process is complet the capacity
of the target hard drive will be seen by a system as 80GB instead of 250GB.
6-6. Button Sound
This option toggles the button sound of the system.
By default it is set to ON, use the up and down arrows to toggle between ON and
OFF.

www.addonics.com Technical Support (M-F 8:30am - 6:00pm PST) Phone: [phone] Email: www.addonics.com/support/query/
6-7. Device Info
This option will diplay the details of everything connected to the controller.
6-8. System Info
This option will display the system information.
7. USB Mode
NOTE: Though this is an active menu option, we recommend you not use
this option since there is no USB connection for this unit. This duplicator is
a standalone unit.
Troubleshooting
LCD
If the LCD display is blank after the device is turned on, check if the power
cable is properly connected and that the power supply is on.
Error Message
If an operation is manually terminated by pressing ESC while the system is running
a copy operation or hardware diagnostics, an error message will show up on the
LCD. This may lead to an illegal operation and cause the device to stop reminding.
If this happens, restart the device.
Source/Target
If the duplicator is unable to read the source or target please check that the data
and power cables are properly connected. When making a copy please make sure
that you set the source correctly.
Keys
If pressing the keys on the front panel produces no response from the system,
the keys may have malfunctioned.
Startup/Shutdown
Do not suddenly turn off the power while the system is performing an operation.
After shutting down normally, wait a moment (usually around 2 seconds) before
restarting the system so it can run self-diagnostics.

www.addonics.com
Phone: [phone]
Fax: [phone]
Email: http://www.addonics.com/sales/query/
CONTACT US
LCD Messages
Connecting with a HDD:
All data will be lost, format?
All data will be lost. Confirm formatting.
Delete Image in Partition xx?
Confirm the deleting of data image in partition xx.
Format?
Ask if you want to format.
Format OK!
The formatting has been completed.
HDD not Format!
The hard disk hasn’t been formatted yet.
HDD too small
The capacity of hard disk is too small.
HDD too small to handle image!
The hard disk hasn’t enough capacity to store the
data image (at least 5Gbytes).
Image Exists Overwrite?
There is a data image in the current partition.
Confirm the overwriting of data.
Image load Fail
The image isn’t successfully loaded from DVD to
the hard disk.
Image load OK
The image is successfully loaded from DVD to
the hard disk
No Image in Partition xx
There is no data image in partition xx.
No Valid HDD!
The system cannot find a hard disk.
Partition Damage
The partition is damaged.
Select HD First!
Select a formatted hard disk at first.
Verify Disk or Partition?
Do you want to verify the hard disk or just a
partition?
Verify Hard Disk Fail!
The hard disk is not verified successfully.
Firmware Update:
Check Sum Error!
The updated firmware has errors.
Flash ROM fail!
Data cannot be written into Flash ROM.
Invalid firmware
The disc doesn’t contain a valid firmware.
Last update F/W Fail!
The firmware is not updated successfully.
Last update F/W OK!
The firmware is updated successfully.
Searching F/W
The system is searching for a valid firmware.
Source can’t be Hard Disk!
During comparison the source cannot be hard
disk.