Disc Makers Forte User manual

DISC MAKERS FORTE
The Forte duplicates in two dierent modes, Single Master
and Multi Master. The single master mode allows you to
make many copies of a commonly used master disc stored
on the hard drive. The multi master allows you to produce
multiple copies of more than one master disc.
t
www.discmakers.com
1-888-800-4038
DUPLICATING
WITH YOUR FORTE:
MAKING COPIES IN
MULTI MASTER MODE:
Conrm the lower right of the display reads MM for
Multi Master. If not refer to the switching to master
mode section in the previous section.
Place the number of blanks you need copied into the
inner bin, below the robotic arm (you can stack multiple
sets of blanks and master discs). Press enter on the“1.
Copy” screen. The Forte will pick up the top master disc
and load that information to the hard drive. Once
completed it will drop the master on the output spindle
and begin duplicating your blanks.
1
2
3
NOTE: Before either process you MUST
make sure the DISC BIN is FULLY EXTENDED
with the SWING GATE tilted TOWARD the UNIT.
SWITCHING BETWEEN SINGLE
MASTER AND MULTI MASTER:
From the main “1. Copy” screen press the Master hot
key directly below the display.
1
Your screen will read master mode multi master like
the following image:
2
MASTER MODE
MULTI MASTER
Use the up and down arrows to rotate through
single master and multi master mode. Then
press “ENT” button to conrm your selection.
3
Press the up arrow until you return to the
“1. Copy” Display.
4
Power on the Forte by ipping the black power switch
located on the back of the unit. When initialization is
complete, this image will appear on the LCD screen:
DISCMAKERS
1. Copy (SM)
5
When the Forte detects a new master disc it will begin
copying it until it dectects another master or the bin is
empty.
MAKING COPIES IN
SINGLE MASTER MODE:
Conrm the lower right of the display reads SM to
stand for Single Master. If not refer to switching to
master mode section in the previous section.
To load the master to the internal hard drive press the
LOAD hot key found underneath the LCD display. Press
the ENT button and the following will appear on the LCD
screen:
1
2
HARD DRIVE SETUP
1. SELECT PARTITION
3Place your master in the inner bin, below the robotic
arm. Press the DOWN arrow until it reads “2. Load New
Partition”and press the ENT key. You will be prompted to
enter a name for the master so it can be retrieved for
future duplicates. Using the arrows buttons scroll
through the alphanumeric characters and press ENT to
select. The master disc will load to the hard drive; when
completed the LCD screen will read Load Partition OK.
Press the ESC button and Up or Down arrows until you
are on the “1. Copy” screen and place the amount of
blanks you need copied in the inner bin.
4
From the “1. Copy” screen press the ENT button and your
recently loaded master will appear on the screen. Press
the ENT button twice to start the burning process
(NOTE: to use counter feature see instructions on back).
Once the burn is done you will be able to retrieve your
copies from the front bin of your Forte.
5
TURN TO THE BACK FOR
FURTHER INSTRUCTIONS
YES! NO!

t
www.discmakers.com
1-888-800-4038
1Start by loading the blank media you are looking to burn
in the rear input bin. If you are not on the “1. Copy”
section of the main menu, use the DOWN arrow to get it.
Once you are on the main page the image will appear as:
BURNING MASTERS STORED
ON THE INTERNAL HARD DRIVE:
2Press the ENT button once on the “1. Copy” main page
section. Then you will taken to a new section to select
your preloaded master label“Choose Partition”. At this
point you will be able to scroll through your preloaded
masters using the UP and DOWN button. The section
you will scroll through will appear like:
DISCMAKERS
1. Copy (SM)
CHOOSE PARTITION:
[SAMPLE ] Audio 123M
3Once you have selected the preloaded master you want
to burn you can press the ENT button. Your Forte will
proceed to burn all the blank media that you have
loaded into the inner bin. Once every disc is burned
you will be able to recieve them from the outer bin.
1Once you have loaded an image; to use counter press
the UP and DOWN arrow buttons to select Specic
Counter, press “ENT”.
USING THE COUNTER:
2Use the UP and DOWN arrow buttons and the“ENT”to
specify the number of copies.