LogiLink WL0130 User manual

Size: 105 x 148mm
* 100P 雪銅紙
* 分兩本手冊, 以騎馬釘裝訂成冊, 一本德文(在前)英文手冊,
另一本西班牙文(在前)波蘭文手冊
* 兩面, 四色彩色印刷

- 1 -
According to the European WEEE directive, electrical and
electronic equipment must not be disposed with consumers waste.
Its components must be recycled or disposed apart from each other.
Otherwise contaminative and hazardous substances can pollute
our environment.
You as a consumer are committed by law to dispose electrical and electronic
devices to the producer, the dealer, or public collecting points at the end of the
devices lifetime for free. Particulars are regulated in national right. The symbol
on the product, in the user's manual, or at the packaging alludes to these
terms. With this kind of waste separation, application, and waste disposal of
used devices you achieve an important share to environmental protection.
1.0 Safety Instructions
Put the Device always on a stable and straight Surface. In case
of falling it can be damaged.
Don’t place the Device into direct Sunlight or in Places with high
Temperature. This can damage the Device or shorten his
average useful Life.
Don’t place it in the near of Heat Sources, like Radiators or other
heat producing Devices.
Don’t expose the Device to Rain, Water, Wetness or high Humidity.
Don’t place it in the Bathroom or the Kitchen in the near of a Sink.
Avoid the direct Contact with Water.
Don’t try to open the Device.
Prior to the first use of our product make a backup of your data.
We are not liable for any loss of data, unless you can accuse us
intention or gross negligence.
In any case, liability for loss of data is limited to the effort that is
necessary to restore from existing backup copies.
Congratulations to the Purchase of LogiLink WL0130!
Please read the Manual and Safety Instructions before using the
product for the first time. Otherwise damage can be the result.

- 2 -
2.0 Introduction
2.1 Specification
Comply with IEEE 802.11n/g/b
standards
Supports high data rate up to 300Mbps
Comply with IEEE 802.3af Powered
Device (PD) standard
High transmit power with good receive sensitivity
Supports point-to-point and point-to-multi point bridge function
Supports WDS (Wireless Distributed System) repeater mode
Supports Universal Repeater and AP Client mode
Supports 64/128-bit WEP, WPA, WPA2 and IEEE 802.1x
wireless securities
Supports WPS hardware button
Provides MAC access control
Provides hidden SSID function
Supports Web-based configuration
Firmware upgradeable
Supports Green WLAN for smart Tx power saving, Implicit Rx
power saving and CPU offload
2.2 Package Contents
1 x Wireless N 300Mbps POE Access Point
1 x AC Power Adapter
1 x Quick Installation Guide
1 x CD (Driver + Manual)
3.0 Installation
3.1 Installing the access point to your Network
Please follow the following instruction to build the network
connection between your new wireless access point and your
computers, network devices:

- 3 -
1. Place the unit in an appropriate place after conducting a site
survey.
2. Connect the access point to ADSL modem, router, or
switch/hub in your network through the LAN port of the access
point by Ethernet cable.
3. Connect the A/C power adapter to the wall socket, and then
connect it to the ‘Power’ socket of the access point.
Note: WL0130 is built in with POE feature on the Ethernet
port. You can connect via RJ45 cable easily to the POE
switch what you have. Then you don’t need the power
adapter.
4. Please check all LEDs on the front panel. ‘PWR’ LED should
be steadily on, LAN LEDs should be on if the access point is
correctly connected to the ADSL modem, router or switch/hub.
3.2 Connecting to access point by web browser
1. Click ‘Start’ button
at lower-left
corner of your computer,
then click control panel.
Double-click Network and
Internet Connections
icon, click Network
Connections, and then
double-click Local Area
Connection, Local Area
Connection Status
window will appear, and
then click ‘Properties’

- 4 -
2. Select ‘Use the following
IP address’, then input
the following settings in
respective field:
IP Address: 192.168.2.2
Subnet Mask:
255.255.255.0
Click ‘OK’ when finish.
3.3 Connecting to Web Management Interface
All functions and settings of this access point must be configured
via web management interface. Please start your web browser,
and input ‘192.168.2.1’ in address bar, then press ‘Enter’ key. The
following message should be shown:
Please input user name and
password in the field
respectively. Then press ‘OK’
button, and you can see the
web management interface
of this access point:
Default:
User name: admin
Password: 1234

- 5 -
Note: If you can’t see the web management interface, and
you’re being prompted to input user name and password
again, it means you didn’t input username and password
correctly. Please retype user name and password again.
If you’re certain about the user name and password you
type are correct, please check to ‘4-2 Troubleshooting’ in
the manual to perform a factory reset, to set the
password back to default value.
3.4 Wireless Access Configuration
3.4.1 Select an Operating Mode for Wireless Access Point
This access point can be operated in different modes; you can
click ‘Basic Setting’ on the left of web management interface to
select an operating mode you want to meet for different needs:

- 6 -
Here you can change the “MAIN ESSID” to what you wanted and
later you can connect to network with this ESSID, default ESSID
is LogiLink.
3.4.2 Setup Wireless Security
You can select “WEP” or “WPA pre-share key” encryption for the
wireless network.

- 7 -
WPA Pre-shared key is the safest encryption method currently,
and it’s recommended to use this encryption method to ensure
the safety of your data.
When you select ‘WPA pre-shared key’ as encryption type, the
following messages will be displayed:
After you finish with setting, please click ‘Apply’, and the following
message will be displayed:
When you see this message, the settings you made is
successfully save. You can click ‘Continue’ button to back to
previous page and continue on other setting items, or click
‘Apply’ button to restart the wireless access point and the
changes will take effect after about 30 seconds.

- 8 -
3.5 Connect your computer with the Repeater
1. Log on to the computer.
2. Open Connect to a Network by right-clicking the network icon
( or ) in the notification area.
3. Choose the wireless
network from the list that
appears, and then click
Connect.
4. Type the network security
key or passphrase if you are
asked to do so, and then
click OK. You'll see a
confirmation message when
you are connected to the
network.
For advanced settings and other features of this Wireless N PoE
Access Point, please refer to user manual enclosed in supplied
CD-ROM.
CE Declaration:
This device corresponds to EU directive 1995/5/EC and
2006/95/EC: With the CE sign Logilink®, a registered
trademark of the 2direct GmbH ensures, that the product is
conformed to the basic standards and directives. These standards
can be requested online on www.logilink.com. All trademarks and
registered brands are the property of their respective owners.