Logitech Keys-To-Go User manual

Keys-To-Go
Ultra-portable keyboard
for Android™ and Windows®
Setup Guide

2
Keys-To-Go - Ultra-portable keyboard
Contents
English. . . . . . . . . . . . . . . . . . . 3

English 3
Keys-To-Go - Ultra-portable keyboard
Know your product
www.logitech.com/support/keys-to-go-tablet
PDF
ON
1 2
1
1
2
2
3
2.5 h
®
2s
®
®
Keys-To-Go AW
3
Keys-To-Go
Ultra-portable keyboard Clavier ultra-portable
OFF
4
6
7
9
8
2
1
35
1. Hot keys
2. Keyboard
3. Bluetooth® connect key
4. Battery check key
5. Bluetooth and battery status light
6. On/o switch
7. Micro-USB charging port
8. Micro-USB charging cable
9. Documentation

4 English
Keys-To-Go - Ultra-portable keyboard
Set up your product
1. Turn on the keyboard:
ON
Bluetooth discovery starts automatically
and continues for 15 minutes. The status
light blinks blue.
If the status light briefly turns red,
charge the battery. For more information,
see “Charge the battery.”
2. Establish Bluetooth connection:
®
®
Keys-To-Go AW
Make sure your tablet’s Bluetooth feature is
on. Go to Settings > Network connections
section, and turn on the Bluetooth function.
3. Pair the keyboard with your tablet:
(i) In your tablet’s Bluetooth settings
page, select “Keys-To-Go AW” in the list
of Available devices.
(ii) When prompted, enter the PIN
displayed using the keyboard.
When successful connection is made,
the status light turns solid blue for a short
time, and then turns o.
(iii) Press enter to confirm the PIN code.
Tip: If “Keys-To-Go AW” isn’t in the list, you can
try pressing and holding the Bluetooth connect
key on your keyboard for 2 seconds or press
scan (or equivalent) on your tablet to search for
Bluetooth devices.

English 5
Keys-To-Go - Ultra-portable keyboard
Charge the battery
You should charge the battery when:
• the status light turns red briefly when
you turn on the keyboard, or
• the status light blinks red when you press
the battery check key:
®
A fully charged battery provides about
3 months of power when the keyboard is used
about two hours a day.
Charging your battery
1. Use the micro-USB charging cable provided
to connect the keyboard to your computer
or a USB power adaptor. The status light
blinks green while the keyboard is charging.
USB
2. Charge your keyboard until the status light
turns solid green.
Each minute of charging gives you about
two hours’ use.
Note: This ratio is approximate and is based on the
standard user experience. Your result may vary.
It takes 2.5 hours to fully charge the battery.

6 English
Keys-To-Go - Ultra-portable keyboard
Hot keys
fn + Back: Esc
Android home/
Windows browser home
Switch applications
Android menu/
Windows contextual menu
Mail
Music
Previous track
Play/Pause
Next track
Volume down
Volume up
Print screen
Bluetooth connect
fn + battery check:
Android lock screen/
Windows 8 lock screen/
Windows 7 sleep

English 7
Keys-To-Go - Ultra-portable keyboard
Function keys
fn + X = Cut
fn + C = Copy
fn + V = Paste
Windows Start key
Android search/Windows search
fn + Left arrow = Home
fn +Up arrow = Page up
fn + Down arrow = Page down
fn + Right arrow = end
fn + Back = Forward delete
For Android:
ctrl + space =
Language layout switch*
For Windows:
alt + shift =
Language layout switch*
Note: To select a function key, press and hold the fn key, and then press the key indicated above.
*Language layout switch:
1. Choose the key combination which is applicable to your specific operating system.
2. Please ensure you have more than one language layout selected in order to switch between them.

8 English
Keys-To-Go - Ultra-portable keyboard
Use your product
Status light indications
Light Description
Blinking green The battery is charging.
Solid green When charging, indicates that the battery
is fully charged (100%).
When you press the battery check key,
solid green for 2 seconds indicates that
the battery power is good (above 20%).
Blinking red Battery power is low (less than 20%).
Recharge the battery.
Solid red When you first turn on your keyboard,
the status light shows solid red briefly
if battery power is low.
Blinking blue Fast: The keyboard is in discovery mode,
ready for pairing.
Slow: The keyboard is trying to reconnect
to your tablet.
Solid blue Bluetooth pairing or reconnection
is successful.
Connecting to a dierent device
1. Make sure the keyboard is turned on.
2. On your device, check that Bluetooth is turned on.
Select Settings > Bluetooth > On.
3. Press and hold the Bluetooth connect key on
the keyboard for 2 seconds. The keyboard turns
discoverable for 3 minutes.
4. Select “Keys-To-Go AW” from the Devices menu.

English 9
Keys-To-Go - Ultra-portable keyboard
Use with optional Smartphone Stand
1. Attach the stand to the keyboard.
2. Set your smartphone in stand.
3. You are ready to type.
When you’ve finished using your product
When not in use, turn o the keyboard to conserve battery power.
Note:
• The keyboard enters sleep mode if powered on and not used for 2 hours. To exit sleep mode, press any key.
OFF

10 English
Keys-To-Go - Ultra-portable keyboard
Battery disposal at product end of life
1. Cut along the fabric at the top edge
of the keyboard:
2. Use a screwdriver to pry the fabric away
from the area around the on/o switch:
3. Separate the inner and outer fabric layers,
and pull them away from the corner:
4. Pull back the yellow plate to reveal
the battery and remove it:
5. Dispose of the battery according
to local laws.

English 11
Keys-To-Go - Ultra-portable keyboard
Visit Product Support
There’s more information and support
online for your product. Take a moment
to visit Product Support to learn more about
your new Bluetooth keyboard.
Browse online articles for setup help,
usage tips, and information about additional
features. If your Bluetooth keyboard has
optional software, learn about its benefits and
how it can help you customize your product.
Connect with other users in our Community
Forums to get advice, ask questions,
and share solutions.
At Product Support, you’ll find a wide
selection of content including:
• Tutorials
• Troubleshooting
• Support community
• Online documentation
• Warranty information
• Spare parts (when available)
Go to:
www.logitech.com/support/keystogo-tablet
Troubleshooting
The keyboard does not work
• Press any key to wake the keyboard from
sleep mode.
• Turn the keyboard O and then back On.
• Recharge the internal battery. For more
information, see “Charge the battery.”
• Re-establish the Bluetooth connection
between the keyboard and your tablet:
• On your tablet, check that Bluetooth
is turned on.
• Press and hold the Bluetooth connect
key on your keyboard for 2 seconds.
• Choose “Keys-To-Go AW” from
the Devices menu on your tablet.
The status light briefly turns blue after
the Bluetooth connection is made.
Note: If you have any language compatibility issue,
please install the “Logitech Keyboard plus” application
on your tablet or contact Logitech Customer Care
to get further information:
www.logitech.com/support/keystogo-tablet
What do you think?
Thank you for purchasing our product.
Please take a minute to tell us what you think of it.
www.logitech.com/ithink

www.logitech.com/support/keystogo-tablet
© 2015 Logitech. All rights reserved. Logitech, the Logitech logo, and other Logitech marks are owned by Logitech and
may be registered. Android is a trademark of Google Inc. Windows® and the Windows logo are trademarks of the Microsoft
group of companies. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by Logitech is under license. All other trademarks are the property of their respective owners. Logitech
assumes no responsibility for any errors that may appear in this manual. Information contained herein is subject to change
without notice.
621-000468.002
www.logitech.com