Logo Lites 100-005/K User manual

Model A Turn Signal Kit Installation Guide
Creative Connections, Inc.
Consumer Hot Line: 888-471-LOGO
770-476-7322 In tlanta, G
http://www.logolites.com
P/N: 100-005/K 2008
Creative Connections, Inc.
3407 Du uth Hwy 120
Du uth, GA 30096, USA
“Logo Lites” and the Logo Lites ogo
are registered trademarks of Creative
Connections, Inc.

INTRODUCTION ND PREP R TION
INTRODUCTION
Thank you for purchasing a Logo Lites® Mode A Turn Signa Kit. Your turn signa kit was bui t to
high qua ity standards to provide you with years of re iab e service. This manua shou d serve as a guide for
insta ing a turn signa kit on your vehic e. A though this guide is thorough, each insta ation is different, so it
can not cover a app ications. Most insta ations take ess than three hours.
You can insta the turn signa kit yourse f IF:
1. you have the right too s,
2. you have a reasonab e mechanica and e ectrica aptitude or experience,
3. you have the know edge or diagrams of where wiring, fue ines, brake ines (non-origina Mode A), etc. are
ocated in the vehic e,
4. and you read and fo ow the instructions very carefu y.
SAFETY INFORMATION
•Read the instructions comp ete y before starting the insta ation of your turn signa kit.
•Never attempt automobi e wiring without first disconnecting the battery.
•When using power too s such as a dri , be sure to use the proper safety equipment (eye protection, etc.).
A ways fo ow manufacturer’s recommendations when using power and hand too s.
•The installation discussed is for reference only and does not indicate that any particular configuration
will be safe for all vehicles. safe and secure installation is solely the responsibility of the installer!!
TOOLS NEEDED
♦SAE 3/4” wrench
♦Wire crimp too
♦Wire cutter
♦Wire stripper
♦1/4” F at b ade (common) screwdriver
♦1/2” socket wrench
OVERVIE
This kit provides a the necessary parts to insta a Logo Lites Turn Signa Kit on
your Mode A Ford. The two main parts of the kit are the contro er (Figure 1) and the four
turn signa assemb ies. The turn signa assemb ies are mounted on the bumper under the
bumper c amps, and the contro er is mounted on the gas tank to the eft of the steering
whee with a very strong magnet. The contro er is mounted such that the turn signa
switches are at the bottom as shown in Figure 1. Genera y, the wires are routed from the
contro er, behind the kick pane area, and out to the four corners of the car. The contro er
works on 6 or 12 vo t cars with positive or negative ground. The contro er “senses” the
po arity and vo tage, so there is no wiring to reverse or switches to f ip.
There are two switches on the front of the contro er. The eft switch contro s the eft turn signa s, and
the right one contro s the right turn signa s. When you press one of the switches, you a ternate the
corresponding signa s between on or off. For examp e, press and re ease the eft switch to turn the eft turn
signa s on, then press and re ease the switch again to turn them off. If you want hazard f ashers, simp y turn on
both eft and right turn signa s. To turn off the hazard ights, press and re ease both switches.
Figure 1

HARD ARE COMPONENTS
Review a the parts shown in the ist be ow. We strive to make qua ity products, so no parts shou d be
missing or damaged. However, if a part is missing or damaged, contact Creative Connections, Inc. about your
Logo Lites product at the Consumer Hot Line phone number isted on the front page of this manua for
immediate response.
Qty Item Qty Item Qty Item
1 Contro er 4 Turn Signa Assemb ies 1 Ma e, 5 Pin Connector
1 Sma Screwdriver 4 Fema e Bu et Connectors 4 Ma e Bu et Connectors
1 Large Ring Termina 1 Sma Ring Termina 1 Push On Connector
50’ B ack Wire 1 Fuse Ho der 1 1 Amp Fuse
6” B ack Wire 5’ Red Wire
INSTALLATION
STEP 1: ATTACH TURN SIGNAL ASSEMBLIES
1. Disconnect battery.
2. There are four turn signa assemb ies. Crimp one MALE bu et connector to each turn signa assemb y wire.
3. Using 3/4” SAE wrench, remove bumper c amp nut from back of bumper c amp.
4. Remove bumper c amp backing p ate.
5. S ide 1 turn signa assemb y over the stud with ens assemb y towards edge of car.
6. Re-assemb e with turn signa assemb y between bumper c amp backing p ate and bumper bracket and
tighten firm y.
7. Repeat for other 3 turn signa assemb ies.
TIP: Tie wrap the wires to the bottom of the bumper brackets with black tie wraps to hide the black wire.
STEP 2: RUN IRES
1. Remove driver’s side kick pane .
TIP: In closed cars, remove dash panel for easiest access.
2. Run a separate wire from dash through kick pane area out to each turn signa assemb y. Leave enough extra
wire at the dash end to connect to the contro er when it is mounted on the gas tank.
TIP: Run the 4 black wires through steering column grommet.
TIP: Tie wrap rear wires to original rear going
harness.
TIP: Run rear wire across with right brake light
wire.
TIP: Put a small piece of tape around the dash
end of the left hand wires when you run them to
keep track of them for inserting into the 5 pin
connector.
3. At each corner of the car, crimp a FEMALE
bu et connector to the wire and p ug onto
MALE bu et connector of each turn signa
assemb y.
4. Crimp arge ring termina on the short b ack
wire (from parts bag) and crimp push on
connector on the other end of the wire. Illustration 1: Wiring Diagram

5. Remove eft most gas tank bo t with socket wrench.
6. Insert gas tank bo t through arge ring termina on short b ack wire.
7. Re-insta gas tank bo t to comp ete chassis connection.
8. The fuse ho der must now be insta ed in the 5’ red wire. Start by cutting about 6” of red
wire off of the 5’ piece.
9. Crimp sma , insu ated #10 ring termina to one end of the 6” fuse wire.
10. Crimp opposite end of the 6” wire to b ue fuse ho der.
TIP: If you are not familiar with this type of fuse holder, then hold it in your hand with the two metal pieces at the
top and facing you. The wires go into the fuse holder at the bottom, through
the holes from the left and from the right. Push one wire into the right side
until it hits the middle stop, you may have to twist the wire to get it to go into
the hole. Now take the piece on the top right (with the metal in it) and fold it
towards the wire until it contacts the wire. Now take a pair of pliers and press
it the rest of the way down until the latch catches. Repeat this for the wire on
the left side. The fuse holder is an insulation displacement type, which means
you do not have to cut the installation off of the wire before you crimp the fuse
holder to the wire.
11. Crimp remaining red wire to the opposite end of the fuse ho der.
12. With fuse ho der inside the cab, insert ring termina through speedometer
cab e ho e in firewa and into the termina b ock.
13. Connect ring termina to the termina b ock post that the ignition coi is
not connected too. Caution: Do NOT connect to ignition switch
terminals.
14. Run the 4’ 6” red wire from fuse ho der, routing it behind the kick pane area, and up to the dash.
15. Strip approximate y 1/4” to 5/16” of insu ation off of the end of the red wire and the 4 b ack wires ocated
inside the cab.
16. Unscrew the five screws in the five pin connector severa turns so that there
is enough room for the wires to be inserted under the tiny c amps.
17. With screw termina s facing you and wire ho es on the eft, insert red, power
wire into top ho e of connector (see Figure 2) and tighten screw.
18. Insert eft turn signa two wires into the next two ho es (see Figure 2) and
tighten firmly.
19. Insert right turn signa two wires into the bottom two ho es (see Figure 2) and
tighten firmly.
20. Rep ace kick pane .
STEP 3: ATTACH CONTROLLER
1. Push chassis connector onto top termina of contro er.
2. Insert 5 pin connector into contro er jack.
3. A ow magnet to attach the contro er to the gas tank.
4. Insta 1 Amp safety fuse into fuse ho der.
5. Re-connect battery.
Illustration 3: Terminal Box
Figure 2
Illustration 2:
Fuse Holder

TROUBLESHOOTING
Symptom Test/Solution
Turn Signa s
Do Not
Work:
1. Make sure battery is charged and connected.
2. Make sure 5 pin connector is fu y inserted and power wire is tight.
3. Make sure chassis connector is fu y pushed onto contro er and is tight y connected to
chassis at the ring termina .
4. Touch test ight to top screw of 5 pin connector. If it does not ight, the fuse may be b own,
the power connection may not be good at the termina b ock post, or the screw may not be
tight enough. Unit can safely use 1, 2, or 3 mp fuse.
5. Turn the turn signa on and touch contro er case with test ight. If the test ight ights, the
chassis connection is bad.
One Signa
Light Does
Not Work
If one ight does not work, swap the wire with another ight on the 5 pin connector. If ight sti
does not come on, the wire going to the ight is shorted to the chassis, there is a poor connection
in the bu et connector, or the turn signa assemb y has a poor connection to the chassis.
If the other ight that previous y did work now does not work in the same position as the first
ight that did not work, you either have a bad 5 pin connector or a bad contro er. Contact
Creative Connections at the Consumer Hot Line on the front of this manua for he p.
LIMITED ARRANTY
Creative Connections, Inc. (hereinafter “CCI”) warrants to the Purchaser of this unit that this unit wi be free of defects in
workmanship and materia s for a period of one (1) year from the date of purchase. “Defects” as used herein, refer on y to those
imperfections which impair the uti ity of the product. Defective units reported or returned to CCI within one (1) year from date of
purchase wi be exchanged or repaired without charge at the option of CCI.
This warranty is imited to the repair or exchange of the product and does not cover and CCI wi not pay nor provide any
other benefit or service inc uding abor or materia s which may be necessary to remove or rep ace a defective unit. CCI sha not be
iab e for any injury, oss or damage, direct or consequentia , arising out of the use or fai ure of this product. It is the user’s
responsibi ity to determine the suitabi ity of this product for its intended use. User assumes any and a risk or iabi ity in connection
with the insta ation and use of this product. This warranty does not app y to any defects resu ting from abuse, neg igence, intentiona
damage, modification, improper insta ation, unreasonab e use, exposure to e ements, or over-tightening of fasteners.
Defective units shou d be reported direct y to CCI and not to your retai er. Contact CCI through the Consumer Hot Line
through the te ephone number shown on the front of this manua or write to the address shown on the back of the manua . Identify the
Logo Lites product purchased, the date and ocation of purchase, and the nature of the a eged defect. Do not ship your product back
to CCI un ess and unti specifica y directed to do so. Shipping instructions wi be provided to you at the appropriate time. A
defective products returned must be accompanied by proof of purchase.
This warranty is not transferab e and app ies on y to products so d within the United States of America, the District of
Co umbia, the Commonwea th of Puerto Rico, territories of the United States, and Canada.
THIS LIMITED W RR NTY IS IN LIEU OF LL OTHER EXPRESS W RR NTIES. CCI SH LL NOT BE
LI BLE TO NY SPECI L, INCIDENT L OR CONSEQUENTI L D M GES. NY IMPLIED W RR NTY OF
FITNESS FOR P RTICUL R PURPOSE, MERCH NT BILITY OR OTHERWISE, PPLIC BLE TO THIS
PRODUCT, SH LL BE LIMITED IN DUR TION TO THE DUR TION OF THIS LIMITED W RR NTY. Some states do
not a ow the exc usion or imitation of incidenta or consequentia damages, so the above imitation or exc usion may not app y to you.