Logosol 0458-395-0861 User manual

This manual describes installation of the electric motor
for the Logosol band sawmill.
Please see the user manual for your band sawmill
for information on assembly, settings and safety instructions.
Read through the user manual carefully and make sure
you understand its contents before using the saw.
4.6 / 8 KW ELECTRIC MOTOR
USER MANUAL
ORIGINAL USER MANUAL.
EN
SKU: 0458-395-0861
EN
REV: 1

2
1
Read through all the set-up instructions before starting to set up, then
follow the instructions step by step as you work.
Numbering for installation sequence
FINAL SAW HEAD ASSEMBLY,
4.6 / 8 KW ELECTRIC MOTOR
PACK SUPPLIED
8400-000-0070
8400-000-0072
8400-000-0074
8400-000-0076
4.6 kW electric motor, 400V
8 kW electric motor, 400V
4.6 kW electric motor, 230V
8 kW electric motor, 230V
After assembly, follow the instructions under Setup sequence in the sawmill manual
to complete setup before starting the machine.

3
1
4 x – M10
8 x – M10
4 x – M10x40
4.6 / 8 KW ELECTRIC MOTOR
Top view:
B751 / B751 PRO, 4.6 / 8 kW electric motor
The electric motor comes with the hinge switch
connected. Assembly consists of installing the motor
on the motor shelf, as well as mounting the pulley
and drive belt. The illustration shows the hole pattern
for installing the 4.6 / 8 kW electric motor. Follow the
assembly instructions, then run through the setup
sequence for the machine when assembly is complete.
Install the motor on the motor shelf.
ELECTRIC MOTOR 4.6 / 8 KW

4
2
1 x
1 x
3
2 x – M6x25
2 x – M6x30
2 x – 03-02182
1 x – 03-02080
1 x – 03-01997
M6x25 M6x30
10mm
12mm
12mm
10mm
Now install the safety hinge in the
existing holes.
Install the pulley on the shaft so that
it fits on the key. Then secure the
pulley with the stop screw.
ELECTRIC MOTOR 4.6 / 8 KW

5
4
5
1 x – M5x50
2 x – M5x16
6 x – 6x16x1
3 x – M5
1 x – 9038-013-0003
1 x – 9038-013-0004
035
035
040
040
1 x – 9020-011-0091
2 x – M5x16
4.6 / 8 KW ELECTRIC MOTOR
Fit the switch box on the
handle tube.
Fit the drive belt over the wheel
and pulley.
ELECTRIC MOTOR 4.6 / 8 KW
4.6 kW
8 kW
Possibility of phase
change to change the
direction of rotation
of the motor.

6
01
101 1
HOLD PRESS
Turn the dead man’s switch to (1) to turn on the power supply
to the machine.
Hold down the dead man’s switch (button on the right) to start
the motor. Then press the start button (on the left). You can
release the left button when the motor has started. The motor
will now run until the dead man’s switch is released.
START THE MOTOR
TURN ON/OFF THE SWITCH BOX

7
4.6 / 8 KW ELECTRIC MOTOR
Read through all the set-up instructions before starting to set up,
then follow the instructions step by step as you work.
It is important to adjust the saw head before starting to ensure satisfactory
sawing and the correct functioning of the sawmill. Follow the setup
sequence carefully! Certain adjustments affect other machine settings.
SETUP SEQUENCE
IMPORTANT!
Now you have finished installing the motor, go back to the manual
for your band sawmill and carry on with the setup sequence,
starting at the point as indicated in the instructions below.
Well done!

Fiskaregatan 2, SE-871 33 Härnösand, Sweden
0611-182 85 | [email protected] | www.logosol.se