Lorex L222A8 Series User manual

User Manual
L222A8 Series

User Manual
L222A8 Series
#LX400115; r. 3.0/57178/57178; en-US iii

Thank you for purchasing this product. Lorex Corporation is committed to providing our customers with a high
quality, reliable security solution.
This manual refers to the following models:
L222A8
For the latest online manual, downloads and product updates, and to learn about our complete line of accessory
products, please visit our website at:
lorex.com
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE
COVER. NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle,
is intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF THE PLUG
TO THE WIDE SLOT AND FULLY INSERT.
#LX400115; r. 3.0/57178/57178; en-US iv

Table of contents
1 Important Safeguards ........................................................................... 1
1.1 General Precautions..................................................................... 1
1.2 Installation ...............................................................................1
1.3 Service....................................................................................2
1.4 Use ........................................................................................3
2 Package Contents.................................................................................4
3 Recorder Overview ..............................................................................6
3.1 Front Panel...............................................................................6
3.2 Back Panel ...............................................................................6
4 Basic Setup.........................................................................................7
4.1 STEP 1: Initial Setup ................................................................... 7
4.2 STEP 2: Setting Up the Recorder ..................................................... 8
4.3 STEP 3: Connecting with Lorex Cirrus .............................................. 9
4.4 STEP 4: Installing the Cameras ......................................................10
4.4.1 Installation Tips..............................................................10
4.4.2 Installing the Cameras ......................................................11
4.4.3 Optimizing Motion Detection..............................................14
4.5 Quick Access to System Information................................................15
5 Using the Mouse .................................................................................16
6 Using the Recorder’s On-Screen Display...................................................17
6.1 Using the Taskbar ......................................................................17
6.2 Using the Quick Menu.................................................................17
6.3 Using the Mini Menu ..................................................................18
6.4 Using the On-Screen Keypads........................................................18
7 Recording .........................................................................................20
7.1 Recording Time for Motion Detection ..............................................20
7.2 Configuring Manual Recording ......................................................21
7.3 Changing Recording Resolution .....................................................22
7.4 Setting a Recording Schedule ........................................................23
8 Playback...........................................................................................25
8.1 Using Playback.........................................................................25
8.2 Playback Controls . .. ... .. .. .. ... .. .. ... .. .. .. ... .. .. .. ... .. .. ... .. .. ... .. .. .. .. ... .. .. .25
9 Search & Backup................................................................................27
9.1 Using Backup Mode ...................................................................27
9.2 Backing Up Videos using Playback Mode..........................................28
9.2.1 Back Up Entire Recordings ................................................28
9.2.2 Video Clip Backup ..........................................................30
9.3 Drive Menu Controls ..................................................................31
10 Managing Users, Passwords and Permissions .............................................33
10.1 Changing Passwords...................................................................33
10.2 Adding a New User ....................................................................33
10.3 Setting User Permissions..............................................................34
11 Pairing Cameras.................................................................................36
11.1 Pairing Cameras with Lorex Cirrus..................................................36
11.2 Pairing Cameras using the Recorder Interface .....................................37
12 Storage.............................................................................................39
12.1 Configuring Storage Overwrite ......................................................39
12.2 Formatting Storage Devices ..........................................................40
13 Using the Main Menu...........................................................................41
13.1 Main Menu Overview .................................................................42
13.1.1 Copying Channel Settings to Another Channel .........................43
13.2 Settings Menu...........................................................................43
13.2.1 Changing a Camera’s On-Screen Display (OSD) .......................43
#LX400115; r. 3.0/57178/57178; en-US v

Table of contents
13.2.2 Enabling / Disabling Cameras .............................................44
13.2.3 Camera Firmware............................................................44
13.2.4 Enabling Audio ..............................................................45
13.2.5 Changing the Display Resolution .........................................46
13.2.6 Menu Transparency .........................................................46
13.2.7 Configuring Basic Network Settings......................................47
13.2.8 Setting up Email Notifications.............................................48
13.2.9 Setting an Email Schedule..................................................49
13.2.10 Configuring Motion Detection Settings ..................................50
13.3 System Menu ...........................................................................52
13.3.1 Changing the Date and Time...............................................52
13.3.2 Changing On-Screen Language ...........................................52
13.3.3 Changing Video Output — NTSC and PAL .............................53
13.3.4 Configuring Menu Time-out Option ......................................54
13.3.5 Configuring Daylight Savings Time (DST)..............................55
13.3.6 Configuring NTP ............................................................55
13.3.7 View System Information ..................................................56
13.3.8 Logs — Searching and Backing Up.......................................57
13.4 Advanced Menu........................................................................58
13.4.1 Manual Firmware Upgrade.................................................59
13.4.2 Restoring Default Settings .................................................59
13.4.3 Exporting System Settings .................................................60
13.4.4 Importing System Settings .................................................61
13.4.5 IPC Upgrade..................................................................62
13.4.6 Configuring System Warning Settings....................................63
14 Connecting to Your System Using PC or MAC ...........................................65
15 Connecting to Your System Using Smartphone or Tablet Apps .................. .....66
16 Viewing Backed Up Video on PC/Mac ......................................................67
16.1 Running Lorex Player 11..............................................................67
16.2 Lorex Player 11 Interface Overview.................................................68
16.2.1 About the Advanced Menu.................................................68
17 Smart Home & Voice Assistance .............................................................70
18 DDNS Setup (Advanced).......................................................................71
18.1 STEP 1: Port Forwarding .............................................................71
18.2 STEP 2: Create a LOREX Account..................................................71
18.3 STEP 3: Add Your Address...........................................................72
18.4 STEP 4: Activate Your Warranty ....................................................72
18.5 STEP 5: Sign Up for a DDNS Account .............................................73
18.6 STEP 6: Enable DDNS on the recorder .............................................74
19 Troubleshooting..................................................................................76
20 Technical Specifications .. ... ................ ... ... ................ ... ... ... ............ ... ... ..78
20.1 Wire-Free Recorder (L222A8 Series) ...............................................78
20.1.1 System ........................................................................78
20.1.2 Inputs/Outputs ...............................................................78
20.1.3 Playback & Display .........................................................78
20.1.4 Recording.....................................................................78
20.1.5 Storage & Archive...........................................................78
20.1.6 Connectivity..................................................................78
20.1.7 General........................................................................78
#LX400115; r. 3.0/57178/57178; en-US vi

Important Safeguards1
In addition to the careful attention devoted to quality standards in the manufacturing process of
your product, safety is a major factor in the design of every instrument. However, safety is your
responsibility too. This sheet lists important information that will help to ensure your enjoyment
and proper use of the product and accessory equipment. Please read them carefully before oper-
ating and using your product.
1.1 General Precautions
1. All warnings and instructions in this manual should be followed.
2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use a
water-dampened cloth for cleaning.
3. Do not use this product in humid or wet places.
4. Keep enough space around the product for ventilation. Slots and openings in the storage cab-
inet should not be blocked.
5. It is highly recommended to connect the product to a surge protector to protect from damage
caused by electrical surges. It is also recommended to connect the product to an uninterrupti-
ble power supply (UPS), which has an internal battery that will keep the product running in
the event of a power outage.
CAUTION
Maintain electrical safety. Power line operated equipment or accessories connected to this product should bear
the UL listing mark or CSA certification mark on the accessory itself and should not be modified so as to defeat
the safety features. This will help avoid any potential hazard from electrical shock or fire. If in doubt, contact
qualified service personnel.
1.2 Installation
1. Read and Follow Instructions: All the safety and operating instructions should be read be-
fore the product is operated. Follow all operating instructions.
2. Retain Instructions: The safety and operating instructions should be retained for future
reference.
3. Heed Warnings: Comply with all warnings on the product and in the operating instructions.
4. Polarization: Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement of
the obsolete outlet.
5. Power Sources: This product should be operated only from the type of power source indi-
cated on the marking label. If you are not sure of the type of power supplied to your location,
consult your video dealer or local power company. For products intended to operate from
battery power, or other sources, refer to the operating instructions.
#LX400115; r. 3.0/57178/57178; en-US 1

Important Safeguards1
6. Overloading: Do not overload wall outlets or extension cords as this can result in the risk of
fire or electric shock. Overloaded AC outlets, extension cords, frayed power cords, damaged
or cracked wire insulation, and broken plugs are dangerous. They may result in a shock or
fire hazard. Periodically examine the cord, and if its appearance indicates damage or deterio-
rated insulation, have it replaced by your service technician.
7. Power-Cord Protection: Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them. Pay particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the product.
8. Surge Protectors: It is highly recommended that the product be connected to a surge protec-
tor. Doing so will protect the product from damage caused by power surges. Surge protectors
should bear the UL listing mark or CSA certification mark.
9. Uninterruptible Power Supplies (UPS): Because this product is designed for continuous,
24/7 operation, it is recommended that you connect the product to an uninterruptible power
supply. An uninterruptible power supply has an internal battery that will keep the product
running in the event of a power outage. Uninterruptible power supplies should bear the UL
listing mark or CSA certification mark.
10. Ventilation: Slots and openings in the case are provided for ventilation to ensure reliable op-
eration of the product and to protect it from overheating. These openings must not be
blocked or covered. The openings should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should never be placed near or over a radia-
tor or heat register. This product should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided and the product manufacturer’s in-
structions have been followed.
11. Attachments: Do not use attachments unless recommended by the product manufacturer as
they may cause a hazard.
12. Water and Moisture: Do not use this product near water — for example, near a bath tub,
wash bowl, kitchen sink or laundry tub, in a wet basement, near a swimming pool and the
like.
13. Heat: The product should be situated away from heat sources such as radiators, heat regis-
ters, stoves, or other products (including amplifiers) that produce heat.
14. Accessories: Do not place this product on an unstable cart, stand, tripod, or table. The prod-
uct may fall, causing serious damage to the product. Use this product only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer or sold with the product. Any
mounting of the product should follow the manufacturer’s instructions and use a mounting
accessory recommended by the manufacturer.
15. Camera Extension Cables: Check the rating of your extension cable(s) to verify compli-
ance with your local authority regulations prior to installation.
16. Mounting: The cameras provided with this system should be mounted only as instructed in
this guide or the instructions that came with your cameras, using the provided mounting
brackets.
17. Camera Installation: Cameras are not intended for submersion in water. Not all cameras
can be installed outdoors. Check your camera environmental rating to confirm if they can be
installed outdoors. When installing cameras outdoors, installation in a sheltered area is
required.
1.3 Service
1. Servicing: Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to qualified serv-
ice personnel.
#LX400115; r. 3.0/57178/57178; en-US 2

Important Safeguards1
2. Conditions Requiring Service: Unplug this product from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled or objects have fallen into the product.
• If the product has been exposed to rain or water.
• If the product has been dropped or the cabinet has been damaged
• If the product does not operate normally by following the operating instructions. Adjust
only those controls that are covered by the operating instructions. Improper adjustment of
other controls may result in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation.
• When the product exhibits a distinct change in performance. This indicates a need for
service.
3. Replacement Parts: When replacement parts are required, have the service technician veri-
fy that the replacements used have the same safety characteristics as the original parts. Use
of replacements specified by the product manufacturer can prevent fire, electric shock, or
other hazards.
4. Safety Check: Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks recommended by the manufacturer to determine that the
product is in safe operating condition.
1.4 Use
1. Cleaning: Unplug the product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
2. Product and Cart Combination: When product is installed on a cart, product and cart com-
bination should be moved with care. Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to overturn.
3. Object and Liquid Entry: Never push objects of any kind into this product through open-
ings as they may touch dangerous voltage points or “short-out” parts that could result in a
fire or electric shock. Never spill liquid of any kind on the product.
4. Lightning: For added protection of this product during a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall outlet and discon-
nect the antenna or cable system. This will prevent damage to the product due to lightning
and power line surges.
#LX400115; r. 3.0/57178/57178; en-US 3

Package Contents2
HD Wire-Free Security Cameras
Rechargeable Power Pack* Camera Antenna*
HD Recorder Toolkit Mounting Kit*
HDMI Cable Power Pack Adapter Ethernet Cable
USB Mouse Recorder Power Adapter
* Per camera in multi-camera packs.
#LX400115; r. 3.0/57178/57178; en-US 4

Package Contents2
NOTE
Hard drive size, number of channels, and camera configuration may vary by model. Check your package to con-
firm that you have received the complete system, including all components shown above.
#LX400115; r. 3.0/57178/57178; en-US 5

Recorder Overview3
3.1 Front Panel
1. PWR – LED Indicator: Glows to indicate the
system is on.
2. REC – LED Indicator: Glows to indicate that
the system is recording video.
3.2 Back Panel
1. Power (12V): Connect the included 12V DC
power adapter.
2. LAN: Connect the included Ethernet cable to a
router or switch on your network for local and re-
mote connectivity.
3. HDMI: Connect the included HDMI cable to
view the system interface on an HDMI monitor or
TV (1080p output supported).
4. USB (Mouse / Backup): Connect the included
mouse or a USB flash drive (not included) for the
purposes of backing up recorded video.
5. microSD / Storage USB: Connect a microSD
card (included with certain configurations) or a
USB storage drive (not included) for video stor-
age purposes. For more details on storage options,
see 12 Storage, page 39.
#LX400115; r. 3.0/57178/57178; en-US 6

Basic Setup4
4.1 STEP 1: Initial Setup
Before you begin, you will need to prepare the wire-free cameras and Power Packs.
NOTE
Power packs come fully charged with no need for initial charging.
To prepare the cameras:
1. Attach an antenna to each camera. Twist the adjustment ring counterclockwise to reposition
each camera as shown below. Twist clockwise to tighten when finished.
U222AA Series
#LX400115; r. 3.0/57178/57178; en-US 7

Basic Setup4
2. Peel off the PLEASE REMOVE label covering the contacts on each Power Pack. Insert the
charged Power Packs into each camera base. Push up until the Power Pack ‘clicks’ into place.
U222AA Series
4.2 STEP 2: Setting Up the Recorder
Next, you must set up the recorder.
To set up the recorder:
1. Connect the recorder to your router using the in-
cluded Ethernet cable.
#LX400115; r. 3.0/57178/57178; en-US 8

Basic Setup4
2. Connect the included mouse to the Mouse / Backup
USB port on the recorder.
3. Connect a monitor (not included) to the HDMI port
of the recorder using the included HDMI cable.
4. Connect the included power adapter to the recorder.
Wait a few minutes for the system to start
4.3 STEP 3: Connecting with Lorex Cirrus
Connect to your system using the free Lorex Cirrus app for smartphones and tablets (iOS and
Android).
To connect with Lorex Cirrus:
1. Download and install the free Lorex Cirrus app from the App Store or Google Play Store.
2. Tap the Lorex Cirrus icon ( ) to launch the app.
3. Tap to open the menu. Tap Devices, then tap Add.
4. Enter the following:
#LX400115; r. 3.0/57178/57178; en-US 9

Basic Setup4
A. Ensure Device ID is selected.
B. Tap to scan the QR code on the back of your recorder using the camera on your mobile
device.
C. Ensure the Client Port reads 35000.
D. Enter the username (default: admin).
E. Enter the password (default: 00000000).
F. Tap Save.
5. Enter a new, secure 8-15 character password. This password will be used to connect to
your system from now on.
6. Your cameras will appear on the Live screen of the app. Tap the play button ( ) to stream
live video on channels that are in sleep mode.
NOTE
If you do not see video from one or more cameras, ensure you have removed the PLEASE REMOVE label
from the Power Pack. If the issue persists, see 19 Troubleshooting, page 76.
4.4 STEP 4: Installing the Cameras
4.4.1 Installation Tips
Follow the tips below for more accurate motion detection and to optimize battery life:
•See images below for ideal setup. It is recommended to place your camera at least 7ft (2.1m)
above the ground and angle it slightly downward toward the monitoring area, excluding any
busy areas (e.g., sidewalks or roadways).
• Ensure the camera image is free of obstructions (i.e., tree branches).
• Position the camera no more than 20ft (6.1m) away from the area you wish to monitor.
• It is recommended that you customize motion settings for each camera on your system. See
4.4.3 Optimizing Motion Detection, page 14 for full details.
• For best performance, position the camera so that objects of interest will move from side-to-
side across the camera image, rather than moving towards or away from the camera.
#LX400115; r. 3.0/57178/57178; en-US 10

Basic Setup4
• Install the camera within range of the wireless receiver (noted in the camera’s specifications).
• This camera is weather resistant for outdoor use (IP66 rated). Installation in a sheltered loca-
tion is recommended.
•Battery life will vary based on temperature, settings and number of events.
4.4.2 Installing the Cameras
Follow the instructions below to mount the cameras. It is recommended that you refer to the "In-
stallation Tips" section to help you select good mounting locations (see 4.4.1 Installation Tips,
page 10).
To install your cameras:
1. Set the mounting bracket in the desired mounting position. Mark holes through the mounting
bracket (shown as orange X’s below).
2. Drill holes where marked for the mounting screws using the included drill bit (item C in
toolkit).
3. Secure the bracket to the mounting surface with the included mounting screws (×4). Make
sure all screws are fastened tightly using the included screwdriver (item A+B in toolkit).
NOTE
• Insert the included drywall anchors if you are mounting the camera onto drywall.
• The hole at the top of the mounting bracket will be used in step 5, once the camera is attached to the
mounting plate.
#LX400115; r. 3.0/57178/57178; en-US 11

Basic Setup4
4. Lower the camera base onto the mounting bracket so the 2 tabs in the mounting bracket lock
into the 2 slots in the camera base.
U222AA Series
5. Insert the security screw through the fasteners on the top of the camera base and mounting
bracket to secure the camera to the mounting bracket. Tighten using the included screwdriver
(item A+B in toolkit).
U222AA Series
#LX400115; r. 3.0/57178/57178; en-US 12

Basic Setup4
6. Tighten the pre-installed locking screw on the base of the Power Pack using the included
screwdriver (item A+B in toolkit).
NOTE
You will need to loosen the locking screw to remove the Power Pack in the future.
7. Adjust the angle of the camera:
U222AA Series
Twist the adjustment ring counterclockwise to reposition the camera. Tighten the adjustment ring when
finished.
A. Adjustment ring
1. Use the included cable clips to complete the installation.
#LX400115; r. 3.0/57178/57178; en-US 13

Basic Setup4
A. Cable
B. Mounting surface
4.4.3 Optimizing Motion Detection
Customize motion detection settings to ensure motion events are being recorded and reduce false
alarms.
To optimize motion detection:
1. Launch the Lorex Cirrus app.
2. Tap a channel in Live View to select it.
3. Tap , then tap Alarm Settings.
4. Configure the following as needed:
a. Sensitivity: The amount of motion needed to trigger recording (e.g., higher sensitivity
requires less motion to trigger recording).
b. Detection: Enable/disable motion detection or person detection per channel.
c. Area Selection: Configure the active area for motion detection so that only areas of in-
terest are selected and detected.
d. Distance Setting: Configure distance setting for motion detection. While watching the
camera’s video on your mobile device, recreate a motion event in front of your camera.
The icon will change from to when motion is detected by the camera. Change
the distance setting if motion detection is being triggered by unwanted events.
NOTE
Distance will be affected by temperature.
e. Buzzer: Set the recorder to sound an alarm when motion is detected.
#LX400115; r. 3.0/57178/57178; en-US 14