Louvolite 1100 Series User manual

Operation Step Operation Result Illustration
Technical
data
Battery Specication: Li-ion Batter, 2000mAH, 7.4V.
Motor Torque/Speed: 1.1Nm/25rpm
Setup the
motor
Motor
assembly 1
A. Remove grease
protector ring by
opening the split
ring and sliding off
the motor body
B. Fit Crown by opening the
split ring and slide along the
motor body until it meets
the motor head
C. Fit the drive
using the circlip to
secure in position
D. Attached motor plate
with the screws supplied in
either left hand or right hand
orientation as required
Pairing
remote
transmitter
with motor
1
Hold down the
SETTING button
on the motor
mount
Motor jogs 2 times
2
Please release this
button when the
motor jogs
3
Select channel for
blind and press the
CONFIRM button
on the remote
within 10 seconds
Motor jogs 2 times. Remote
has now been paired with
the motor
Changing
motor
rotation
direction
1 Press UP button
If blind goes up the motor
direction is ok. If the blind
goes down then the motor
direction should be changed
2
Hold down LIMIT
button and then
press STOP button
on the remote
transmitter
Hold both buttons until
motor jogs - at this moment
the motor rotation direction
has been changed
General Information
Illustration shows the side of motor head with SETTING
button facing you.
• Motor antenna should be as straight as possible;
otherwise, the receiving distance will be reduced.
Remote
Transmitter
Motor
Remote
Transmitter
Motor
Press and hold
Release it
1
2
3
1
2
Issue: 1/15
®
Lithium Rechargeable Battery Motor
Instructions - 1100 Series
R1710 - Battery Motor
R1720 - 5 Channel Remote Control

Operation Step Operation Result Illustration
Selecting
a channel
1Press the CHANNEL
+ or CHANNEL - The blue light on the
remote will illuminate
which channel is
currently selected.
Setup
bottom
limit
1Press and hold LIMIT
button on the remote Motor jogs 3 times
2Release the button Motor is ready to set
limits
3Press DOWN button
on the remote Motor runs down
4Press STOP button
when motor gets
close to the end-point
of lower limit
Motor stops
5Press DOWN button Motor runs step by
step to set lower limit
accurately
6Press CONFIRM
button on the remote
The motor jogs 2
times. The setting has
completed
Setup
upper limit
7Press UP button on
the remote
Motor runs up
8Press STOP button
when the motor is
running close to the
upper stop point
9Press UP button Motor runs step by
step to adjust upper
limit accurately
10 Press CONFIRM
button on the remote
Motor jogs 2 times.
The setting has
completed
Setup mid-
point limit
11 Press UP or DOWN
button on the
remote then press
STOP when desired
mid-point height is
reached
Motor runs up or
down
12 Press and hold LIMIT
button rst then
whilst holding LIMIT
press UP button on
the remote
Hold both buttons
until motor jogs. Mid-
point is now set
13 To move blind to mid-
point position press
STOP
Motor runs up or
down to mid-point if
not already at mid-
point
Primary
12
13

Press and hold
Release it
Secondary
1
23
Delete mid-
point limit
14 Press UP or DOWN
button on the remote
to send blind to
upper or bottom limit.
Motor runs up to
upper limit or down
to bottom limit
15 Press and hold LIMIT
button rst then
whilst holding LIMIT
press UP button on
the remote
Hold both buttons
until motor jogs. Mid-
point is now deleted
Pairing
additional
remote
transmitter
1
Hold down the
SETTING button on
the motor mount
Motor jogs 2 times
2 Please release this
button when the
motor jogs
3Press the CONFIRM
button on the remote
within 10 seconds
Motor jogs 2 times.
Remote has now
been paired with the
motor
Charging The motor works with Li-ion battery, please charge when the motor stops working or falters. Please
charge the motor by charger. Charging time: Charger 5 to 6 hours.
Delete
original
setting on
motor
1
Press and hold
SETTING button on
the motor mount
The motor will jog 2
times rstly, then jog
3 times
2 Release the button
All the records have
been deleted - motor
reset
FAQ
If the motor does not work:
• Please charge the motor battery rst.
• If the motor does not stop at the required point, then the stops must be reset.
12
Press and hold Release it
15
14