Low Range Off-Road SEB-TD User manual



Suggested Tools:
•Standard Screwdriver: Small
•Phillips Screwdriver #2
•Phillips Screwdriver #3
•Impact Drill W/ #2 and #3 Phillips Bits
•Allen Sockets: 4mm & 5mm
•Impact Driver W/#2 and #3 Phillips
Bits (Optional)
•Hammer (if Impact Driver is Used)
CAUTION: Safety glasses should be
worn at all times when working with
vehicles and related tools and
equipment.
Ultimate Suzuki Samurai Tube Doors w/ Arm Saver
Latch System by Low Range Off-Road
(SKU# SEB-TD)
Installation Instructions
For additional copies of these
and other instructions go to:
www.lowrangeoffroad and click on the
“Instructions” tab.
Instructions Created by an:



Step 2"
Remove the (3) phillips screws using a
#2 phillips bit in an impact drill.
Note: These screws can be hard to
remove. If you do not have an impact
drill, you could use an impact driver.
Click HERE to see how to use an
impact driver. Click HERE to purchase
an Impact driver from LROR.
Step 1"
Pop the side view mirror cover open
using a standard screwdriver.
Step 4"
Open the door.
Step 3"
Remove the side view mirror and set it
aside.
Note: This mirror will be used with the
new tube doors.



Step 6"
Roll the window down 2 or 3 inches so
you will have a way to hold the door.
Then close the door.
Note: It may be a good idea to roll the
window all the way down to protect the
glass during storage.
Step 5"
Disconnect the body side of the door
strap by removing the (2) phillips screws
using a #2 phillips screwdriver. Leave
the door strap attached to the door.
Step 8"
Remove the bottom (2) phillips screws
using a #3 phillips screwdriver in an
impact drill.
Note: If there are spacer washers under
these hinges keep track of them and
where they were. It may be necessary
to reinstall them with the new doors.
Step 7"
LOOSEN the top (2) phillips screws
using a #3 phillips screwdriver. Do not
remove these screws yet.
Note: These screws can be very hard to
remove. If you do not have an impact
drill, you could use an impact driver.
Click HERE to see how to use an
impact driver. Click HERE to
purchase an Impact driver from LROR.



Step 10"
While supporting the door with one
hand, open the door with the other and
set the door aside.
Step 9"
Remove the top (2) phillips screws.
Note: If there are spacer washers under
these hinges keep track of them and
where they were. It may be necessary
to reinstall them with the new doors.
Caution: Hold the door in place while
removing these screws.
Step 12"
Align the holes of the hinge and the tube
door and install both of the supplied top
screws. Leave these screws loose for
now.
Step 11"
Position the new door in the door
opening and latch it.



Step 14"
Once all the screws are started, tighten
all (4) screws using a 5mm allen socket.
Step 13"
Align the holes of the hinge and the door
and install both of the supplied bottom
screws. Leave these screws loose for
now.
Step 16"
The latch should hit the striker as close
to the middle as possible. If it does skip
to Step 19. If it does NOT. you will need
to loosen the hinge screws and adjust
the door up or down and retighten the
screws.
Step 15"
Open the door and then close it again.
Be sure it is latches and unlatches
properly.



Step 18"
Check to see that the door latches and
unlatches correctly. Adjust the hinges
and or striker if needed.
Step 17"
The door striker can also be adjusted if
necessary. To adjust, loosen the screws
using an #3 phillips screwdriver,
reposition the striker as needed, and
retighten the screws.
Step 20"
Insert one of the supplied screws.
Note: Be sure to use the supplied
screws. The OEM screws are not the
correct length.
Step 19"
Position the mirror trim as shown and
align the holes.



Step 22"
Start the other (2) screws.
Step 21"
Start the screw using a 4mm allen
socket.
Step 24"
Snap the cover back into place . . .
Step 23"
Once all the screws are started, tighten
them all.



Congratulations!"
You have successfully installed the
Tube Doors w/ Arm Saver Latch
System by Low Range Off-Road.
We hope these instructions have
been helpful. If you have
suggestions on how to make these
instructions (or products) better,
p l e a s e e m a i l u s a t :
[email protected]
Step 25"
. . . and adjust the mirror.
Step 26"
Install the second door following the
same procedures as the first door.



As always, If you experience any difficulty during the installation of this product
please contact Low Range Off-Road Technical Support at 801-805-6644 M-F
during regular store hours. Thank you for purchasing from Low Range Off-Road.
These instructions are designed as a general installation guide. Installation of many Low Range
Off-Road products require specialized skills such as metal fabrication, welding and mechanical
trouble shooting. If you have any questions or are unsure about how to proceed, please contact
our shop at 801-805-6644 or seek help from a competent fabricator. Using fabrication tools such
as welders, torches and grinders can cause serious bodily harm and death. Please operate
equipment carefully and observe proper safety procedures.
Rock crawling and off-road driving are inherently dangerous activities. Some modifications will
adversely affect the on-road handling characteristics of your vehicle. All products sold by Low
Range Off-Road are sold for off road use only. Any other use or application is the responsibility
of the purchaser and/or user. Some modifications and installation of certain aftermarket parts may
under certain circumstances void your original dealer warranty. Modification of your vehicle may
create dangerous conditions, which could cause roll-overs resulting in serious bodily injury or
death. Buyers and users of these products hereby expressly assume all risks associated with any
such modifications and use.
Revised 11/04/15© Copyright 2015 Low Range Off-Road, LC!!!!!! All Rights Reserved