LOWE'S 1688VA-60-274-925-UM User manual

1
ATTACH YOUR RECEIPT HERE
Serial Number__________________ Purchase Date__________________
Questions, problems, missing parts? Before returning to your retailer, call our customer service
department at
888-251-1026 , 8 a.m. - 8 p.m., EST, Monday - Sunday.
60-IN VANITY WITH TOP
ITEM #5141650; 5141659; 5141676
MODEL #1688VA-60-274-901-UM; 1688VA-60-274-925-UM; 1688VA-60-274-926-UM
1688VA-60-274-901-UM O21 60-IN NOVA CERUSED NATURAL OAK VANITY/ENGINEERED WHITE TOP
1688VA-60-274-925-UM O21 60-IN NOVA CERUSED NATURAL OAK VANITY/ENGINEERED CARRARA TOP
1688VA-60-274-926-UM O21 60-IN NOVA CERUSED NATURAL OAK VANITY/ENGINEERED CALACATTA TOP
MODEL NUMBER DESCRIPTION

2
TABLE OF CONTENTS
Package Contents...........................................................................................................................3
Hardware Contents..........................................................................................................................3
Safety Instructions...........................................................................................................................3
Preparation......................................................................................................................................4
Assembly or Installation Instructions...............................................................................................4
Care and Maintenance...................................................................................................................11
Warranty.........................................................................................................................................11
Replacement Parts List.................................................................................................................12

3
HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)
PACKAGE CONTENTS
SAFETY INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, operate or install the
product.
WARNING
• There are several assembly steps, including unpacking, that require two adults.
CAUTION
• Follow these instructions closely, take your time, and use care while assembling this vanity.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PART DESCRIPTION QUANTITY CARTON
A Vanity 1
B Top 1
D Sink 2
C Backsplash 1
Box 2 of 3
Box 1 of 3
Box 3 of 3
E
Tip-out Door
(preassembled to
vanity (A))
2 Box 2 of 3
GG HH II JJ KK
Lock Washer
Qty. 8
Nut
Qty. 8
Wrench
Qty. 1
Bolt
Qty. 8
Sink Bracket
Qty. 8
AA
Touch Up Pen
Qty. 1
B
D
D
A
E
E
C

4
INSTALLATION INSTRUCTIONS
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not attempt
to assemble the product.
Estimated Installation Time: 45 minutes (24 hours for silicone caulk to dry).
Tools Required for Installation (not included): Phillips screwdriver, utility knife or scissors, silicone
caulk, power drill with drill bit, measuring tape, level
WARNING
Vanity (A) MUST be secured to wall.
Note: Clean area where the vanity (A) will be
permanently located prior to beginning installation,
ensuring the vanity (A) will not interfere with any
water supply and drain lines once mounted.
1. With two people, carefully place vanity (A)
against the wall in its final location.
While holding the vanity base firmly against the
wall, use the pre-assembled levelers on the
bottom of each leg of the vanity (A) to level the
item. Twisting the levelers counterclockwise
will raise the height of the vanity (A), and
twisting them clockwise will lower the vanity.
Once the vanity is in place, against the wall,
and level from front to back and side to side,
drill a hole through the vanity mounting area
and into the wall studs (as illustrated in
diagram 1). Using appropriate mounting
hardware (not included), secure the vanity (A)
to a wall stud. If possible, secure the vanity
(A) to two wall studs for increased stability.
1
12
A

5
INSTALLATION INSTRUCTIONS
2. Take out the top (B) and backsplash (C)
according to the steps indicated by the
drawings on the right, and place them face
down onto a scratch free surface such as a
foam sheet that came in the packaging.
3. Apply silicone caulk (not included) to
the top edge of sink (D). With the help of
another adult, lower the sink onto the back
side of the stone top.
Make sure the sink over-flow hole is facing
the front of stone top.
Be sure to align the sink well with the stone top
cut out allowing for equal stone overhang on the
front, back and sides of the ceramic sink (D).
Repeat for the remaining sink.
Note: To install the sink onto the top correctly,
ensure that the two "BACK" stamps on the sink
and the top are aligned on the same sides.
Use the guide lines marked on the sink and
bottom side of stone top to assist with sink
location.
2
Remove the top foam sheet
Remove the backsplash and place
it on a scratch free surface
C
Foam sheet
C
Remove the foam sheet
B
BACK
FRONT
BACK
FRONT
Remove the top and place it
on a scratch free surface
B
BACK
FRONT
BACK
FRONT
Foam sheet
Remove the cutout foam
sheet & hardware
1
2
1
2
B
Hardware
Pack
Hardware
Pack
2
2
BACK
BACK
D
B
2
2
BACK
BACK
D
3
BACK
1
Sink Lip
Top
BACK
BACK

6
INSTALLATION INSTRUCTIONS
Hardware Used
Bolt x 8
4. Screw bolts (GG) into the threaded holes of
stone top (B).
Hardware Used
Sink bracket x 8
Nut x 8
x 8Lock Washer
Wrench x 1
5. Lower the sink brackets (HH) over the bolts
(GG) and allow to rest on the sink lip. Adjust
location of bracket to firmly grasp sink lip.
Lower lock washers (JJ) over bolts (GG) and
secure with nuts (II). Hand tighten nuts (II)
with included wrench (KK).
DO NOT OVER TIGHTEN!
Repeat for the remaining sink.
Tip: Check that the sink placement is well
centered front to back and side to side of the
stone top cut out before allowing the silicone
caulk to dry. If the sink is not centered well
unscrew sink clamps, re-adjust the sink position
and re-tighten the sink brackets.
GG
HH
II
JJ
KK
4
GG
D
D
B
BACK
BACK
BACK
BACK
5
3
II
JJ
GG
KK
2
HH
1
D
D
B
BACK
BACK
BACK
BACK

7
INSTALLATION INSTRUCTIONS
6. To install the Top (B) to the vanity (A).
Apply silicone caulk to the top edge of the
wood cabinet. With the help of another adult,
gently lower the stone top with assembled sink
onto the cabinet. Make sure the stone top is flush
with the back side of the wood cabinet and the
stone overhang is equal on both sides over the
wood cabinet left and right side walls. Remove
any excess caulk before allowing to dry.
Helpful tip: it may be easier to install your
choice of faucet (not included) before securing
the vanity top (B) to vanity base (A).
7. Apply silicone caulk (not included) to unpolished
side and bottom of backsplash (C). Position
backsplash (C) on top (B) and against wall.
Clean any excess caulk before allowing
to dry.
6
1
2
2
A
B
7
1
22
C
B

8
INSTALLATION INSTRUCTIONS
9. To reinstall drawer(s) into vanity (A), fully
extend metal glide tracks. Gently lower and
slide drawer box into rear glide catch. Next,
lower drawer box down to completely rest
on extended glides. Then, push plastic levers
to lock the drawer box in place.
Repeat for remaining drawers.
Note: Drawer box alignment can be adjusted,
if necessary. As shown in the diagram, spin
the adjustment wheel to the left to raise the
drawer box, or to the right to lower the drawer
box. The left and right-side glide heights can
also be adjusted independently in order to find
the drawers best alignment position.
CAUTION
DO NOT force drawer or damage to glide(s) may
occur. If drawer does not slide in with ease,
remove and try again from the start.
8. As shown in the diagram, fully extend the
drawer and locate the plastic levers on the
metal glide tracks. Push the left-side and
right-side levers at the same time to
disengage the drawer from the drawer glides.
Gently lift the drawer up to remove it from
vanity (A).
8
A
12
9
A
3
2
1

9
INSTALLATION INSTRUCTIONS
11. If you need to adjust the tip-out door, do so in the following manner.
To adjust tip-out door left or right, loosen screws (a) on both hinges, adjust tip-out door, and
retighten screws.
To adjust tip-out door up or down, turn screws (b) on both hinges, in or out.
To adjust tip-out door in or out, loosen screws (c) on both hinges, adjust tip-out door, and
retighten screws.
11
3
a
1
a
1
c
3
c
1
1
b
22
2
2
2
2
10
1
E
E
2
10. Gently open the tip-out door (E) and use the
Phillips screwdriver to loosen the screws
holding the solid wood tip-out tray. Once
loosened, simply lift and slide up to remove
(per diagram 10).

10
INSTALLATION INSTRUCTIONS
Assembly is now complete. Install desired
faucet and drain assemblies (neither included)
per the manufacturers’ instructions to complete
the installation.
12
E
E
2
1
12. Re-hang the wood tray back inside of the
top tip-out door (E).