Lowrance HOOK2 7x GPS TS User manual

| 1
HOOK2 series | Quick Guide - EN
HOOK Quick Guide
5 HDI, 5TS, 7x GPSTS, 7 HDI, 7TS, 9 HDI, 9TS and 12TS models
Front controls
2
3
5
4
67
1
1Pages Press to activate the Home page.
2Zoom in/
out
Press to zoom the image.
Press both keys simultaneous to create a MOB
(Man Over Board) waypoint at the vessel's
position.
3Arrows
On any full screen page: press to position the
cursor on the image. Press to pan the image in
any direction.
On multi-panel pages: press to select panel.
In menus and dialogs: press to highlight an
option.
4Exit (X)
On a maximized multi-panel page: press to
return to the multi-panel page.
In menus and dialogs: press to return to
previous menu level and to exit a dialog.
5Menu/
Enter
On any full screen page with no menu or
dialog active: press to display the menu.
On multi-panel pages: press to maximize the
current selected panel.
In menus and dialogs: press to conrm a
selection.
6Cursor/
Waypoint
Press to activate/deactivate the cursor.
Press and hold to save a waypoint.
7Power Press to display the System Controls dialog.
Press and hold to power the unit on/o.
EN
*988-11771-001*

2|
HOOK2 series | Quick Guide - EN
Micro SD card
The card reader position
depends on model.
System controls dialog
• Option ON
• Option OFF
Display illumination
• Set brightness and select day/night mode from the System Controls dialog
• Repeat short presses on the Power key to cycle the backlight brightness
The Home page
1 2
3
1. Tools panel
2. Page icons
3. Customize option
¼Note: Page icons on the Home page vary with model type.
Pages
Select a page icon on the Home page to display a page.

| 3
HOOK2 series | Quick Guide - EN
Custom pages
• Select the Add Page icon to create a
custom page
• Switch Customize ON to edit custom
pages
Multi-panel pages
• With cursor not active on any panel: switch active panel by using the Arrow keys. An
active panel is indicated with an orange border
• Activate the cursor by pressing the Cursor/Waypoint key, then use the arrow keys to
position the cursor
• Maximize the active panel by pressing the Menu/Enter key. Press the X key to go
back to the multi-panel page
• Adjust panel size by selecting Adjust in the System controls dialog, then use the
Arrow keys to set preferred panel size. Conrm the layout by pressing the Menu/
Enter key
¼Note: You must maximize a panel in a multi-panel page to use the panel menu.
Charts and GPS plotter pages
Chart page (not available for 7x TS models) GPS Plotter page (7x TS models)
• Zoom the image by using the Zoom keys
• Pan the image in any direction by using the Arrow keys
• Display item information by positioning the cursor on an item and then pressing
the Menu/Enter key

4|
HOOK2 series | Quick Guide - EN
Creating a route on a chart/GPS Plotter page
1. Activate a full screen page or maximize the panel on a
multi-panel page
2. Press the Menu/Enter key to activate the menu, then select the New route option in
the menu
3. Press the Arrow keys to position the rst route point, then press Menu/Enter key to
conrm the position
4. Repeat step 3 to position additional route points
5. Press the X key to save the route
Trails
The system automatically tracks and draws the vessel's movement on the
chart/GPS Plotter panel. Trails are managed from the Trails dialog.
To display the trails dialog:
1. Select Waypoints, Routes, Trails from the Home page
2. Select the Trails tab in the dialog
3. Select the trail you want to edit
Change chart source if card is inserted
¼Note: Charts not available for 7x TS models.

| 5
HOOK2 series | Quick Guide - EN
Sonar, StructureScan and DownScan pages
Sonar StructureScan
(TripleShot models)
DownScan
• Zoom the image by using the Zoom keys
• Use the Arrow keys to view the sonar history
By default the unit is set to Auto mode, and all settings are automated.
• Change to Custom mode to allow for customizing the settings.
Sonar StructureScan and DownScan
Creating waypoints
Press and hold the Cursor/Waypoint key to save a new waypoint.
• With cursor inactive, the waypoint is placed at the vessel's position
• With cursor active, the waypoint is placed at the cursor position
Overlay data
The data type can be changed, and the item position on the image is
selectable.
The data items can be turned on/o from the System Controls dialog.
Each data item can be removed individually from the panel:
1. Select the Edit overlay option in the System Controls dialog to turn
the unit into edit mode
2. Press the Menu/Enter key to display edit options
3. Press the X key to leave edit mode

6|
HOOK2 series | Quick Guide - EN
Logging sonar data
Sonar data can be logged and saved to internal memory.
Creating a Man Over Board (MOB) waypoint
Activate a MOB waypoint by pressing both Zoom keys simultaneously.
Settings dialogs
Used for system conguration.
Product manuals
For the full Operator manual, technical specications and declarations, refer to the
product website on: www.lowrance.com.