LOXONE Touch Nightlight Air User manual

Technical Specifications
Power supply 5VDC via Micro USB Power supply
Power consumption typ. <150mW, max. 5W
Touch points 7 touch points, capacitive
touch detection
Safety rating IP20
Dimensions 120x120x75mm /
4.72x4.72x2.95” (LxWxH)
Maintenance & Cleaning This device is free of main-tenance
and may only be cleaned with a dry
cloth.
Information
Contains FCC ID: COR-ZWIR4512AC1
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received,
including interference that may cause undesired operation
Loxone Electronics GmbH
Smart Home 1
4154 Kollerschlag
Austria
loxone.com
Need Help?
loxone.com/support
V250320
Part No: 100340
Touch
Nightlight
Air
Power loss max. 5W
Interfaces Loxone Air:
868MHz (SRD Band Europe),
4 channels available
915MHz (ISM Band Region 2),
10 channels available
max. Power 3.16mW
Ambient temperature -40 ... 35°C / -40 ... 91°F
Humidity max. 95% r. H. (non condensing)
Click feedback Yes
Alarm clock function Alarm time adjustable on the
device, built-in alarm signal or
alarm playback via music server
More datas
Lighting RGBW illumination through
back of device as night light
Display Time, alarm time and temperature

About the product
The Touch Nightlight Air features the Loxone Standard T5
touch points to control your lighting, blinds, music, etc.
It displays the current time and allows you to set an alarm.
There is an integrated RGBW light which you can use as a
night light or have it gently wake you leading up to your alarm
going off. Use the additional input to arm your burglar alarm,
for example.
Features
• 5 control touch points & 2 function touch points
• Signal LED (freely assignable)
• Visual display for clock and temperature
• Integrated alarm
• Built-in RGBW light
Installation
Connect device only to the power supply that is shipped with
the product, then:
• If the device is not in learn-in mode, reconnect the Micro
USB and then press and hold the lower middle touch point
(T7) for 5 seconds (this should be done within 10 seconds of
powering on the device).
• A short press of T7 scrolls through the stored alarms. With a
long press of T7, the display will begin to flash and you can
now adjust the time of the selected alarm or, if no alarm
has been created, you can add one. Use the left and right
corner touch points to adjust the hours and minutes. Tap
the T7 touch point once again to confirm.
For additional information, declaration of confirmity,
visit www.loxone.com/help/touchnightlight
Safety Information
Read all safety information before using the device to ensure
safe and proper use.
Follow the warning information provided below
to prevent incidents such as fire or explosion.
• Do not expose the device to physical impact or damage.
• Use only manufacturer-approved chargers, accessories and
power supplies.
• Prevent the jacks from coming into contact with conductive
elements, such as metal or liquids.
• If any part of the device is cracked or broken, stop using the
device immediately and get in contact with Loxone.
• To prevent damage avoid direct sunlight.
• Indoor-use only.
Follow the warning information provided below
to prevent injury to people or damage to the
device.
• Keep out of reach of children and animals.
• Take note of the ambient and storage temperatures. Using
or storing the device outside the recommended temperature
ranges may damage the device.
• Do not use the device in a hot environment or near fire.
• The upper middle touch point (T6) is a freely assignable
input. You could use it to activate Night Mode or arm the
burglar alarm, for example.
1
4
2
6
3
5
7
Function
Lights on /
Change mood
View/Set/Quit Alarms,
View snooze mode,
Learn-in mode
Micro USB
Diffused
RGBW light
This folder is a part of the product!
Blinds up/
Set hours
Music on /
Volume up /
Set minutes
Blinds down /
Set hours
Music off /
Volume down /
Set minutes