Tips Tips Tips
To use the Primary White LED To use the Primary White LED To use the Primary White LED
Press Button for Instant On or Off
Brightness control-
- Press and Release to turn on
- Press and hold to dim beam
- Release hold at desired brightness level
(there will be a "blink" when you have reached
the lowest lighting level)
Safety Beacons-
- Press and hold past Brightness control "blink"
Proton Pro will begin cycling through the safety
beacons.
- Slow beacon
- Medium beacon
- Fast beacon
- SOS
- Release at desired beacon
Signal/Morse code- Squeeze only light
- Press on/off button rapidly until light no longer
stays on.
- To exit press and hold on button until light turns off
Press Button for Instant On or Off
Brightness control-
- Press and Release to turn on
- Press and hold to dim beam
- Release hold at desired brightness level
(there will be a "blink" when you have reached
the lowest lighting level)
Safety Beacons-
- Press and hold past Brightness control "blink"
Proton Pro will begin cycling through the safety
beacons.
- Slow beacon
- Medium beacon
- Fast beacon
- SOS
- Release at desired beacon
Signal/Morse code- Squeeze only light
- Press on/off button rapidly until light no longer
stays on.
- To exit press and hold on button until light turns off
Press Button for Instant On or Off
Brightness control-
- Press and Release to turn on
- Press and hold to dim beam
- Release hold at desired brightness level
(there will be a "blink" when you have reached
the lowest lighting level)
Safety Beacons-
- Press and hold past Brightness control "blink"
Proton Pro will begin cycling through the safety
beacons.
- Slow beacon
- Medium beacon
- Fast beacon
- SOS
- Release at desired beacon
Signal/Morse code- Squeeze only light
- Press on/off button rapidly until light no longer
stays on.
- To exit press and hold on button until light turns off
To use the Secondary Red LED To use the Secondary Red LED To use the Secondary Red LED
Press-Hold-Release to turn on.
Brightness control-
- Press and hold for a brighter red beam.
- Release hold at desired brightness.
- Proton Pro will blink at full brightness.
Safety Beacons-
- Press and hold past Brightness control "blink"
Proton will begin cycling through the safety beacons.
- Slow beacon
- Medium beacon
- Fast beacon
- SOS
- Release at desired beacon
Signal/Morse code- Squeeze only light
- Press and instantly release when the red beam just
comes on, quickly turn off. Repeat four times. The light
will be in red signal mode
- To exit press and hold on button until light turns off.
Press-Hold-Release to turn on.
Brightness control-
- Press and hold for a brighter red beam.
- Release hold at desired brightness.
- Proton Pro will blink at full brightness.
Safety Beacons-
- Press and hold past Brightness control "blink"
Proton will begin cycling through the safety beacons.
- Slow beacon
- Medium beacon
- Fast beacon
- SOS
- Release at desired beacon
Signal/Morse code- Squeeze only light
- Press and instantly release when the red beam just
comes on, quickly turn off. Repeat four times. The light
will be in red signal mode
- To exit press and hold on button until light turns off.
Press-Hold-Release to turn on.
Brightness control-
- Press and hold for a brighter red beam.
- Release hold at desired brightness.
- Proton Pro will blink at full brightness.
Safety Beacons-
- Press and hold past Brightness control "blink"
Proton will begin cycling through the safety beacons.
- Slow beacon
- Medium beacon
- Fast beacon
- SOS
- Release at desired beacon
Signal/Morse code- Squeeze only light
- Press and instantly release when the red beam just
comes on, quickly turn off. Repeat four times. The light
will be in red signal mode
- To exit press and hold on button until light turns off.
1. Proton Pro is designed to indicate when your batteries are low by turning on the red
led at the same time the white is on.
IMPORTANT when using NiMH batteries, recharge them when indicated for
them to continue to be able to accept a full charge.
2. Proton Pro only dims from the primary LED and brightens from the secondary LED.
3. If your light will not turn on check that the batteries are inserted properly, see
polarity on reverse side.
4. If your Proton Pro shuts off after a few seconds hold the button down until light
shuts off. This removes it from point of purchase mode.
5. Need SOS quickly - Press and hold, Release the button the instant of the second
blink after full dimness or full brightness.
6. To turn both LED’s at the same time - Press and hold, instantly release when red beam
blinks the second time. The red light will be blinking in SOS, turn off. Turn back on.
All LED's will be on at the same time. To return to regular functions, press and hold
button until the red beam turns on, turn off.
1. Proton Pro is designed to indicate when your batteries are low by turning on the red
led at the same time the white is on.
IMPORTANT when using NiMH batteries, recharge them when indicated for
them to continue to be able to accept a full charge.
2. Proton Pro only dims from the primary LED and brightens from the secondary LED.
3. If your light will not turn on check that the batteries are inserted properly, see
polarity on reverse side.
4. If your Proton Pro shuts off after a few seconds hold the button down until light
shuts off. This removes it from point of purchase mode.
5. Need SOS quickly - Press and hold, Release the button the instant of the second
blink after full dimness or full brightness.
6. To turn both LED’s at the same time - Press and hold, instantly release when red beam
blinks the second time. The red light will be blinking in SOS, turn off. Turn back on.
All LED's will be on at the same time. To return to regular functions, press and hold
button until the red beam turns on, turn off.
1. Proton Pro is designed to indicate when your batteries are low by turning on the red
led at the same time the white is on.
IMPORTANT when using NiMH batteries, recharge them when indicated for
them to continue to be able to accept a full charge.
2. Proton Pro only dims from the primary LED and brightens from the secondary LED.
3. If your light will not turn on check that the batteries are inserted properly, see
polarity on reverse side.
4. If your Proton Pro shuts off after a few seconds hold the button down until light
shuts off. This removes it from point of purchase mode.
5. Need SOS quickly - Press and hold, Release the button the instant of the second
blink after full dimness or full brightness.
6. To turn both LED’s at the same time - Press and hold, instantly release when red beam
blinks the second time. The red light will be blinking in SOS, turn off. Turn back on.
All LED's will be on at the same time. To return to regular functions, press and hold
button until the red beam turns on, turn off.
Step 1: Activate your light, press and hold button until light shuts off. Step 1: Activate your light, press and hold button until light shuts off. Step 1: Activate your light, press and hold button until light shuts off.
*See instructions *See instructions *See instructions
***
