LS CS18-007 Guide

Leading Solution LS TRACTOR
1. DESCRIPTION :
1/1
1) For improvement of tie-rod, we did change the stopper length setting (+3mm)
2) Assemble the clamp upwards
SUBJECT : To prevent MT3 Tie-rod Interference
MODELS AFFECTED : MT345E, MT350E
CS18-007
Aug. 2018
Ref # :
2. Action : See attached page for instructions on how to modify. (attachments #1)
1) Adjust the stopper length
Charge: HS Oh Check: JE Kim APPR: JE Kim
3. Effected Model :
- MT345E : 2323000002 ~ 2323000242
- MT350E : 2324000002 ~ 2324000280
4. Warranty Status :
- Use below labor code and submit the warranty claim.
- Labor code : G610S01-101 End Ball & Tie Rod –replace (0.3 hrs)
2) Assemble the clamp upwards. : Check the direction of the clamp.
Top view Top view
38mm = 1.50 inch
41mm = 1.61 inch

Leading Solution LS TRACTOR
ADJUSTMENT MANUAL
TIE-ROD CLAMPAND STOPPER BOLT
LS TRACTOR
APPROXIMATE ADJUSTMENT TIME: 0.3 hours
Issue date AUG. 2018
Rev. 01 (ENG)
Attachment #1

Leading Solution LS TRACTOR
TIE-ROD BOLT AND STOPPER BOLT ADJUSTMENT
LS Tractor
MT3E gear
2
ENG

Leading Solution LS TRACTOR
1 - SAFETY INFORMATION
1 - SAFETY INFORMATION
Safety rules
Personal safety
This is the safety alert symbol.It is used to alert you to potential personal injuryhazards. Obey all safety messages
that follow this symbolto avoid possibledeath or injury.
Throughout this manual and on machinedecals, you will find the signal words DANGER, WARNING,and CAUTION
followed by special instructions. These precautions are intended for the personal safety of you and those working
with you.
Read and understand all the safety messages in this manual before you operate or service the machine.
DANGER indicatesa hazardous situationwhich, if not avoided, will result in death or serious injury.
The color associatedwith DANGER is RED.
WARNINGindicatesa hazardous situationwhich, if not avoided, could result in death or serious injury.
The color associated with WARNINGis ORANGE.
CAUTION, used with the safety alert symbol,indicates a hazardous situationwhich, if not avoided, could result
in minoror moderateinjury. The color associated with CAUTION is YELLOW.
FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD
RESULT
IN DEATH OR SERIOUS INJURY.
Machine safety
NOTICE: Notice indicates a situation which, if not avoided, could result in machine or property damage. The color
associated with Notice is BLUE.
Throughout this manualyou will find the signalword Notice followedby special instructionsto prevent machineor
property damage.The word Notice is used to address practices not related to personal safety.
Information
NOTE: Note indicates additional information which clarifies steps, procedures, or other information in this manual.
Throughoutthis manualyou will findthe word Note followed by additionalinformationabout a step, procedure, or
other informationin the manual.The word Note is not intended to address personal safety or property damage.
3ENG

Leading Solution LS TRACTOR
2–TOOL LIST
4
12
3
2–TOOL LIST
Tool list
No Tool name
1Plier
217mm spanner
3Ruler
ENG

Leading Solution LS TRACTOR
3 - GENERALINFORMATION
3- GENERAL INFORMATION
Basic instructions
PLEASE READ THE COMPLETE INSTRUCTIONS BEFORE STARTING ASSEMBLY!
References to right and left are determined bystanding at therear of the machineandfacing thedirectionof travel.
NOTE: When referring to the instructions for callout references, the numeric (example: (1)) refers to item (1) in the
kit contents bill of materials. The letter (example: (A)) refers to the component on the unit, not a component in the kit
contents bill of materials.
NOTE: Using the hardware torque chart, torque all hardware to the specified torque unless otherwisespecified
within
the instructions.
NOTE: Using the hydraulic fitting torque chart, torque all fittings to the specified torque unless otherwise specified
within the instructions.
NOTICE: Do not tighten the hardwareuntil instructed to in the assemblyinstructions.
NOTICE: Be sure to use the hardware specified when using tapped holes as trying to install a metric bolt in an inch
thread or an inch bolt in a metric thread will damage the threads.
NOTE: Install flat washersover all slotted holes unless truss-heador carriage bolts are used. Install a lock washer
on all bolts unless a jam nut or self-locking nut is specified.
NOTE: Install special hardened washers where specified.
5ENG

Leading Solution LS TRACTOR
3 - GENERAL INFORMATION
Safety rules - Personal Safety
Carefully study these precautions, and those included in the external attachment
operators manual, and insist that they be followed by those working with and for you.
1.Thoroughly read and understand this manual and the attachment operators manual before operating this or any
other equipment.
2.Be sure everyone is clear of the machine before starting. Blow the horn, if equipped, three times before starting
engine.
3.Only the operator should be on the machine when in operation. Never allow anyone to climb on to the machine
while it is in motion. If the machine is equipped with an Instructors Seat, this must only be used for training purposes.
Passengers must not be allowed to use the Instructors Seat.
4.Keep all shields in place. Never work around the machineor any of the attachmentswhile wearing loose clothing
that mightcatch on movingparts.
5. Observethe followingprecautions whenever lubricatingthe machineor making adjustments.
•Disengage all clutchinglevers or switches.
•Lower the attachment,if equipped, to the ground or raise the attachmentcompletelyand engage the cylinder
safety locks . Completingthese actions will prevent the attachmentfrom lowering unexpectedly.
•Engage the parking brake.
•Shut off the engine and removethe key.
6. Alwayskeep the machinein gear while going downhill.
7. The machineshould always be equipped with sufficientfront or rear axle weight for safe operation.
8.Under some field conditions,more weight may be required at the front or rear axle for adequate stability.This is
especially importantwhen operating in hilly conditions or/when using heavy attachments.
9.Always lower the attachment,shut off the engine, set the parking brake, engage the transmissiongears and
remove the key before leaving the operators platform.
10.If the attachment or machineshould become obstructedor plugged; set the parking brake, shut off the engine
and remove the key, engage the transmission gears, wait for all machine or attachment motion to come to a stop,
before leaving the operators platformto removing the obstruction or plug.
11.Never disconnect or make any adjustmentsto the hydraulic system unless the machineand/or the attachmentis
lowered to the ground or the safety lock(s) is in the engaged position.
12. Use of the flashing lights is highly recommended when operating on a public road.
13.When transporting on a road or highway, use accessory lights and devices for adequate warning to the
operators of other vehicles. In this regard, check local government regulations. Various safety lights and
devices are available from your LS Tractor dealer.
14. Practicesafety 365 days a year.
15. Keep all your equipment in safe operating condition.
16. Keep all guardsand safety devices in place.
17.Always set the parking brake, shut off the engine and remove the key, engage the transmissiongears, wait for
all machine or attachmentmotionto cometo a stop, before leaving the operators platform to service the
machineand attachment.
18. Remember: A careful operator is the best insurance against an accident.
19. Extreme care should be taken in keeping hands and clothing away from movingparts.
6
ENG

Leading Solution LS TRACTOR
4 - ADJUSTMENT
4 - ADJUSTMENT
4-1. TIE-ROD CIRCLIP ADJUSTMENT
WARNING
Maintenance hazard!
Before performing any maintenance or inspection:
-position machine on a firm, level surface
-turn off the engine
-remove the ignition key
-secure the machine (wheels chocked)
-disconnect the wiring
(unless instructed otherwise)
Failure to comply could result in death or serious injury.
7ENG
(1)
Front view
Top view
1. Check the direction of the clamp.
2. Turn the clip so that the direction of the
clamp matches the top of the
tie-rod end.
3. To do the same job on right tie-rod.

Leading Solution LS TRACTOR
4 - ADJUSTMENT
4-2. STOPPER BOLT ADJUSTMENT (38mm -> 41mm)
WARNING
Maintenance hazard!
Before performing any maintenance or inspection:
-position machine on a firm, level surface
-turn off the engine
-remove the ignition key
-secure the machine (wheels chocked)
-disconnect the wiring
(unless instructed otherwise)
Failure to comply could result in death or serious injury.
1. Measure the length of the stopper bolt.
38mm (1.50 inch)
8
2. Loosen the M12 locking nut.
3. Loosen the stopper bolt so that the length of the
stopper bolt is 41mm. (1.61inch)
38mm
41mm
ENG

Leading Solution LS TRACTOR
5 - ASSEMBLY
9ENG
41mm
4. Tighten the M12 locking nut.
5. Check again that the length of the stopper bolt is
41 mm. (1.61inch)
6. To do the Same job on right stopper bolt.

Leading Solution LS TRACTOR
PRINTED IN KOREA.
AUG. 2018
All rights reserved. No part of the text or illustrations of this publication may be reprodu
ced.
LSMtron policy is one of continuous improvement and the right to change prices, specification or
equipment at
any time without notices is reserved.
All data given in this publication is subject to production variations. Dimensions and weight are approximate
only and the illustrations do not necessarily show products in standard
condition.
For exact information about any particular product, please consult your LS Tractor USA Dealer.
10
Issue date AUG. 2018
Rev. 01 (ENG)