LSIS eXP Series, eXP20-TTA User manual

Right choice for ultimate yield!
LSIS strives to maximize customer’s profit in gratitude of choosing us for your partner.
Human Machine
Interface
XGT PANEL
eXP Series
User
’s Manual
eXP20
-TTA
eXP30
-TTA
eXP30
-TTB
eXP30
-TTE
e
XP40-TTA
eXP40
-TTB
e
XP40-TTE
eXP60
-TTA
eXP60
-TTB

Read this manual carefully before
installing,
wiring, operating, servicing
or inspecting this equipment.

Keep this manual within easy reach
for quick reference.

Safety Precautions
1
Before using the product…
To use the product safety and effectively, please read this instruction manual thoroughly before use.
►Please keep to the safety precaution, for it to prevent accidents and potential danger from
occurring.
►Safety precaution is classified into ‘Warming’and ‘Caution’and their meanings are as follows.
Warning Violating the instruction may result in serious personal injury or death.
Caution Violating the instruction may result in slight personal injury or product
damage.
►The indicated illustrations on the product and in the manual have the fallowing meanings.
Be cautions, for danger may be present.
Be cautions,for there is a possibility of an electric shock.
►After reading the instruction manual, keep it handy for quick reference.

Safety Precautions
2
Design Precautions
Design Precautions
Installation Precautions
►
Install a safety circuit external to the HMI to protect the whole control system in case of
external power supply trouble.
Serious trouble may occur to the entire system due to erroneous output/operation of the HMI.
Warning
►In/output signal or communication cable should be at least 100mm apart from High-
voltage/power wires.
Otherwise, it may cause erroneous output/operation.
►Use the HMI in an environment that meets the general specification contained in this
manual or datasheet.
Otherwise, it could result in electric shock, fire, erroneous operation or deterioration.
►In case of much vibration in the installed environment, be sure to insulate the HMI from
direct vibration.
Otherwise, it could result in electric shock, fire, erroneous operation.
►Be sure not to let foreign substances such as conductive debris inside the product.
Otherwise, it could result in electric shock, fire, erroneous operation.
Caution
Caution

Safety Precautions
3
Wiring Precautions
►Be sure to turn off the HMI and external power before wiring.
Otherwise, it may result in an electric shock or damage to the product.
►Wire correctly by checking each of the product’s rated voltage and terminal layout.
Otherwise, it mayresult in fire, electric shock or erroneous operation.
►Tighten terminal screws with specified torque when wiring.
If terminal screws are loose, it may result in short circuits, fire or erroneous operation.
►Use the exclusive HMI 3-type grounding for the FG terminal.
If not grounded, it may result in erroneous operation.
►Be sure not to let any foreign substances such as wiring debris inside the module.
Such debris may cause fire, damage or erroneous operation.
Warning
Caution

Safety Precautions
4
Startup and Maintenance Precautions
Disposal Precaution
►Do not touch the terminals while power is on.
Otherwise, it may cause electric shock or erroneous operation.
►Turn off the HMI and external power when cleaning or tightening the terminal.
Otherwise, it may cause electric shock or erroneous operation.
►Do not charge, disassemble, heat, short circuit, solder, etc. other battery.
Mishandling the battery may cause overheating, crack, fire and may result in injury or fire.
►Do not disassemble PCB from the product case or modify the product.
Otherwise, it may result in fire, electric shock or erroneous operation.
►Use cellular phone or walky-talky at least 30cm away from the HMI.
Otherwise, it may result in erroneous operation.
►When disposing of this product or battery, treat it as industrial waste.
Otherwise, it may cause poisonous pollution or explosion.
Warning
Caution
Caution

Revision History
5
Revision History
Version Date Contents Revised location
V1.0
‘16.05
First Edition
-
V1.1
’16.07
Additional model (eXP20-TTA)
1-2,2-1~2,3-3,10-3~6,App2-1
V1.2
’17.08
Additional model (eXP30-TTA/TTE)
2-3~4,3-2,11-3~5,App2-2
V1.3
’18.05
eXP30-TTAgeneral standard revision
3-1

※The number of User’s manual is indicated the right side of the back cover.
ⓒLSIS Co., Ltd 2016 All Rights Reserved.

Contents
6
Chapter 1 General Introduction ...................................................................... 1-1~1-6
1.1 How to use the Instruction Manual........................................................................................................1-1
1.2 Feature..................................................................................................................................................1-2
1.3 Terminology...........................................................................................................................................1-6
Chapter 2 System Configuration ....................................................................... 2-1~2-6
2.1 Part Names ...........................................................................................................................................2-1
2.2 System Configuration............................................................................................................................2-5
Chapter 3 Standard Specification....................................................................3-1~3-4
3.1 General Standards................................................................................................................................3-1
3.2 Function Standards...............................................................................................................................3-3
Chapter 4 System Configuration ...................................................................4-1~4-13
4.1 Backlight Setting ...................................................................................................................................4-2
4.2 Touch Calibration..................................................................................................................................4-3
4.3 Date Time Setting .................................................................................................................................4-4
4.4 Environment Setting..............................................................................................................................4-5
4.5 Ethernet Setting ..................................................................................................................................4-11
4.6 XP-Remote Setting .............................................................................................................................4-12
4.7 Buzzer Setting.....................................................................................................................................4-13
Chapter 5 Diagnostics ......................................................................................5-1~5-8
5.1 Screen Diagnosis..................................................................................................................................5-2
5.2 Touch Diagnosis ...................................................................................................................................5-3
5.3 Backup Memory Diagnosis ...................................................................................................................5-4
5.4 Flash Memory Diagnosis.......................................................................................................................5-5
5.5 USB Memory Diagnosis........................................................................................................................5-6
5.6 Serial Communication Diagnosis..........................................................................................................5-7

Contents
7
Chapter 6 Viewing Information of PLC Connection Status ..........................6-1~6-8
6.1 PLC Communication Configuration Settings.........................................................................................6-2
6.2 Connection Information.........................................................................................................................6-3
6.3 PLC Information ....................................................................................................................................6-4
6.4 History of PLC Error ............................................................................................................................6-4
6.5 History of PLC Mode Conversion ........................................................................................................6-5
6.6 History of PLC Power ..........................................................................................................................6-5
6.7 History of PLC System ........................................................................................................................6-6
6.8 N:1 Settings .........................................................................................................................................6-7
6.9 Program Monitor ..................................................................................................................................6-8
Chapter 7 Storage Function.............................................................................7-1~7-4
7.1 General Introduction ............................................................................................................................7-1
7.2 Downloading Project through the Storage Equipment..........................................................................7-2
7.3Uploading Project through the Storage Equipment...............................................................................7-3
7.4Updating the Device through Storage Equipment.................................................................................7-4
Chapter 8 XGT Panel S/W Update........................................................................... 8-1
8.1 General Introduction ............................................................................................................................8-1
Chapter 9 File Backup through External Storage Equipment.......................9-1~9-7
9.1 Path Structure in case of File Backup...................................................................................................9-1
9.2 Operation setting when there is no space for backup...........................................................................9-5
9.3 Structure of path of video file and video capture files...........................................................................9-6

Contents
8
Chapter 10 Installation and Wiring............................................................10-1~10-10
10.1 Installation.........................................................................................................................................10-1
10.1.1 Installation environment...........................................................................................................10-1
10.1.2 Notice in handling....................................................................................................................10-3
10.1.3 Notice in installing the panel....................................................................................................10-3
10.2 Wiring................................................................................................................................................10-7
10.2.1 Power wiring............................................................................................................................10-7
10.2.2 Ground wiring ........................................................................................................................10-10
Chapter 11 Maintenance...............................................................................11-1~11-3
11.1 Maintenance......................................................................................................................................11-1
11.2 Daily Maintenance.............................................................................................................................11-1
11.3 Periodical Maintenance.....................................................................................................................11-2
Chapter. 12 EMC Standard Certification ....................................................12-1~12-2
12.1 Requirement for EMC Standard Certification ..................................................................................12-1
12.1.1 CE standard certification ........................................................................................................12-1
12.1.2 KC standard certification ........................................................................................................12-2
12.2 Requirement for Low Voltage Command Suitability .........................................................................12-2
12.2.1 Standard certification for XGT Panel.......................................................................................12-2
12.2.2 Selection of XGT Panel .........................................................................................................12-2
Appendix 1 Troubleshooting............................................................App1-1~App1-24
1. Type of Problem.............................................................................................................................. App 1-1
2. Problem when Starting.................................................................................................................... App 1-2
3. Problem after the Monitor on........................................................................................................... App 1-4
4. Display Problem of Figure and Object ............................................................................................ App 1-6
5. Communication Problem................................................................................................................. App 1-9
6. USB Removal of Memory Card..................................................................................................... App 1-10
7. Error Message during Execution of Program................................................................................ App 1-11
Appendix 2 Dimension ....................................................................App 2-1~ App 2-3
Appendix 3 Warranty and Environmental Policy........................................... App 3-1

Chapter 1 General Introduction
1-1
Chapter 1 General Introduction
1.1 How to use the Instruction Manual
This instruction manual provides information such as specification, how to use, etc., of the product needed to operate eXP
series of XGT Panel.
The user manual’s configuration is as follows.
Sequence Category Contents
Chapter1 General Introduction It describes this manual’s configuration, product’s feature and term.
Chapter2 System Configuration It describes feature and system configuration of each XGT Panel.
Chapter3 Standard Specification It describes XGT Panel’s general and function specification.
Chapter4 System Configuration It describes XGT Panel’s system configuration.
Chapter5 Diagnostics It describes XGT Panel’s self-diagnosis.
Chapter6 Viewing information of
PLC Connection Status
It describes the way on connection status information of PLC which is
connected with XGT Panel.
Chapter7
Transmission of Project
from USB Storage
Device
It describes the way to execute the project by using USB storage
device.
Chapter8 XGT Panel S/W Update It describes the way to update engine at XGT Panel.
Chapter9 Backup files by using
Storage Devices
It describes the way to backup recipe, logging and etc. files by using
storage devices.
Chapter10 Installation and Wiring It describes an installation, wiring and caution for reliability of PLC
system.
Chapter11 Maintenance
It describes inspection category and method for long normal operation
of PLC system.
Chapter12 EMC Standard It describes system configuration for EMC standard.
Appendix 1 Troubleshooting It describes a variety of error contents and measure.
Appendix 2 Dimension It describes the dimension of XGT Panel.
Appendix 3 Warranty and
Environment Policy
-
Remark
This manual doesn’t describe connection with XP-Builder and PLC. For their own function, Please refer to the related
manuals.

Chapter 1 General Introduction
1-2
1.2 Feature
XGT Panel series has the following features.
(1) Various types of external interface
(a) Supporting various device of USB, Ethernet, it maximizes the customer’s usability.
Various communication connectors are placed at the lower side so that it can be connected in a variety
of types with the control device such as PLC, inverter, etc. Through RS-485, RS-232C, RS-422/485,
Ethernet (10Base-T /100Base-TX) communication, it can be connected with control device.
Status LED
- When power on,
USB DEVICE(eXP30/40/60)
- Project download through
XP-Builder
Battery Cover
- Reset Switch
- Battery,
- Setting Switch,
RS-422/485(eXP40/60)
- Control device that can be communicated such as PLC
USB HOST
- Data Backup
(alarm, logging, recipe, etc.)
- Project data storage
(image, upload project, etc.)
- Mouse, Keyboard,
RS-485(eXP40/60)
RS-422/485(eXP20/30)
- Control device that can be
communicated such as PLC
Ethernet
- Project downloads through XP-Builder
- Control device that can be communicated
such as PLC
-
Connected with fieldbus and open
network
Power Terminal
- Composed of power
input and PE terminal
RS-232C
- Control device that can
be communicated such as
PLC

Chapter 1 General Introduction
1-3
(2) Based on Windows CE
(a) Adoption of Microsoft Company’s Windows CE
•Windows CE 6.0
(b) Advantage
•It provides stable software capacity by using Microsoft Company’s platform.
•It can process diverse function simultaneously.
•It provides diverse interface including Ethernet, USB.
•The user interface including mouse and keyboard can be connected.
•It has high flexibility like computer software.
•Fast reaction is available when adding new equipment.
•Wide data sharing and management with upper system is available (Later).
(3) Improvement of project transmission time
(a) It provides Ethernet which is faster than RS-232C.
(b) It provides the transmission function from USB storage device.
(4) High quality screen
(a) It provides the high quality screen and clearness by high quality LCD.
•It adopts TFT LCD which supports the 65,536 Color.
(b) It provides diverse graphic type.
•It is available to express precisely and actually.
•It provides the simple moving function with GIF support.

Chapter 1 General Introduction
1-4
(5) Analog touch Panel
(a) It adopts analog (resistive) Touch Panel.
•Visibility is improved without the grids.
(b) It provides high touch resolution.
•It can control Touch Panel precisely.
(6) Multilingual and diverse font
(a) It supports the multilingual function.
•It transmits the Windows/User font used in computer to XGT Panel.
•Additional language development is not necessary.
•Multilingual language is an advantage of Windows CE.
(b) It can express twelve kinds of language simultaneously.
•It can express 12 kinds of language simultaneously.
•Language switching is available by using special switch during operation.
(c) It can provide the various fonts.
•Various expressions are available by using the Windows/User font.
•Font size and type can be adjusted freely.

Chapter 1 General Introduction
1-5
(7) Advanced function
(a) Alarm function.
•The History alarm can be classified alarm group and alarm list and selected alarm can be expressed
by alarm search.
•The Flow alarm indicates current or the latest alarm at the bottom of screen.
•The System alarm indicates the important problems from operation.
(b) Logging function
•It provides conditional logging according to device condition and continuous periodic logging which
operates periodically according to time and device status.
•It provides 256Kbyte areas for backup.
•Backup into USB storage device is available.
•Backup data’s type is stored in Excel, it is easy to use.
(c) Recipe function.
•It provides READ/WRITE function.
•It provides 128Kbyte areas for backups.
[General recipe: it set up 10,000 double words for each of one of them.]
•Backup into the USB storage device is available.
•Backup data’s type is stored in Excel, it is easy to use.
(d) Scheduler function.
•It can be set up to Max. 32.
(e) Print function.
•It provides a Screen/Alarm print function.
•It can be printed by USB printer.
(f) Script function.
•It provides more flexible function by user Script.
•It can be diversely applied to such as including Global/Object/Screen indication and so on.
(8) Stable product suitable for international standards
(a) CE, KC standard acquisition
(b) UL(cUL) standard acquisition
(c) NEMA standard acquisition (UL Type 4X)
- Only for eXP20-TTA/DC,CERTI

Chapter 1 General Introduction
1-6
1.3 Terminology
It describes terms used in this manual.
Term Definition Remarks
Module
A standard element that has a specified function which configures the
system.
Devices such as I/O board, which inserted onto the mother board or
base unit..
Ex) CPU module,
Power Module,
I/O module
Unit A single module or group of modules that perform an independent
operation as a part of PLC system. Ex) Basic unit, Extension unit
PLC system
System consisted of PLC and peripheral device which can be
controlled by user program.
-
XP-Builder
Software used to write and edit the project.
-
XP-Manager
It is the software for edition, download, monitoring to realize data
communication between XGT Panels through XP Link with online
control function.
XP-Remote
Software used to remote monitor and control the XGT Panel
Cnet module
Computer Link
-
FEnet module
Fast Ethernet Network
-
RTC
Abbreviation of ‘Real Time Clock’.
It is used to call general IC that contains clock function.
-
1.4 Standard of product name
It describes terms used in this product names.
Term Sign Contents Remark
(A) LCD Size
20
10.9cm (4.3
”
)
30
14.2cm (5.6
”
)
40
17.8cm (7
”
)
60
25.9cm (10.2
”
)
(B) LCD type
T
TFT Color
(D) Product type
A
Advance
Normal
B
Pro plus
Premium
(E) Power type
AC
AC SMPS
AC100-240V
DC
DC SMPS
DC24V
eXP
(A) (B) (C)(D) (E)

Chapter 2 System Configuration
2-1
Chapter 2 System Configuration
Characteristic of each eXP series and its system configuration are as follow;
2.1 Part Names
1. eXP20-TTA/DC, eXP20-TTA/DC,CERTI
①
③
②
④⑤
⑥
⑦⑧
Items Part Names
Descriptions
①Front Part
1) Analog Touch Panel: Input by user’s touch
2) LCD: Screen indication
②Power LED
Indicating the state of device (On: BLUE)
※High Luminance Blue LED
③
Panel Mounting
Panel
Fixing XGT Panel on the panel using bracket

Chapter 2 System Configuration
2-2
Items Part Names
Descriptions
④Power Terminal Composed of Power Input(DC24V) and PE Terminal
⑤USB Interface
1) USB Memory Connection: Backup of data such as alarm/logging/recipe
and
storage of screen data
2) USB Memory Connection: Send/Receive project data, Send XP-Runtime
3) User’s Interface Connection: Using mouse/keyboard
4) Printer connection: Printing function
⑥
Battery Cover
Reset Switch
Backup Battery
Setting Switch
<Setting Switch>
No.1 A Side. Backup Battery On
B Side. Backup Battery Off
No.2 / 3 A Side. RS-422/485 Terminating Resistance On
B Side. RS-422/485 Terminating Resistance Off
No. 4 A Side. O/S Download Mode
B Side. Operating Mode
⑦Ethernet Terminal
Ethernet: 10Base-T/ 100Base-TX
1) Send Project Data
2) Receive backup data and project file
3) Send XP-Runtime
4) PLC/Control Device Communication
⑧RS-232C, RS-
422/485 Connector
RS-232C (COM2): PLC/ Control Device Communication
RS-422/485 (COM3): PLC/ Control Device Communication
※
COM1 is not used.

Chapter 2 System Configuration
2-3
2. eXP30-TTA(B)/DC, eXP30-TTE/DC
①
③
②
⑤ ⑥
⑦
⑧
④
⑨
Items Part Names
Descriptions
①Front Part
1) Analog Touch Panel: Input by user’s touch
2) LCD: Screen indication
②Power LED
Indicating the state of device (On: BLUE)
※High Luminance Blue LED
③USB Device 1) Logging/Recipe/Screen Data Backup 2) Send project data and XP-Run time
3) Receive back data and project file
④Panel Mounting
Panel
Fixing XGT Panel on the panel using bracket
⑤Power Terminal Composed of Power Input(DC24V) and PE Terminal