LTT SLC-M+ Series User manual
Laser Tools & Technics Corp.
User
Manual
Version 1.1 e
SLC-M+ Series
Copyright in this manual is owned y LTT, Inc. 2014
Introduction
Technical Support
Thank you for purchasing the
manufacturing defects for one year from the date of purchase. Our technical support
group is glad to work with you in answering your questions. If you cannot find the
solution to your particular application,
technical assistance, please use the ways as following:
Tel: 886-3-
5727772 (Mon.
Fax: 886-3-
5728898
Email: service@lttcorp.com
We : www.lttcorp.com
Address: No. 121, Lane 99, Pu
Disclaimer
The information provided in this document is believed to be reliable. However, no
responsibility is assumed for any possible inaccuracies or omissions. pecifications
are subject to change without
trademarks of Microsoft. Other trademarks are the property of their respective
owners.
LTT
reserves the right to make changes without further notice to any products herein
to improve reliability, function, or design.
of the application or use of any product or circuit described herein; neither does
convey any license under its patent rights, nor the rights of others.
Special Sym ols
Failure to follow instructions may lead to product damage, or error.
Failure to follow instructions may lead to injury by
Failure to follow
1
Introduction
Thank you for purchasing the
LC-M+
series. This product is warranted to be free of
manufacturing defects for one year from the date of purchase. Our technical support
group is glad to work with you in answering your questions. If you cannot find the
solution to your particular application,
or, if for any reason you need additional
technical assistance, please use the ways as following:
5727772 (Mon.
-Fri., 8:30 -
18:00, Taiwan)
5728898
Email: service@lttcorp.com
We : www.lttcorp.com
Address: No. 121, Lane 99, Pu
-
Ding Road, Hsin Chu City, Taiwan, R.O.C.
The information provided in this document is believed to be reliable. However, no
responsibility is assumed for any possible inaccuracies or omissions. pecifications
are subject to change without
notice. The Windows 2000/XP/Vista
trademarks of Microsoft. Other trademarks are the property of their respective
reserves the right to make changes without further notice to any products herein
to improve reliability, function, or design.
LTT does not assume any liability arising out
of the application or use of any product or circuit described herein; neither does
convey any license under its patent rights, nor the rights of others.
Failure to follow instructions may lead to product damage, or error.
Failure to follow instructions may lead to injury by
electric shock
Failure to follow
instructions may lead to injury by
invisible
series. This product is warranted to be free of
manufacturing defects for one year from the date of purchase. Our technical support
group is glad to work with you in answering your questions. If you cannot find the
or, if for any reason you need additional
18:00, Taiwan)
Ding Road, Hsin Chu City, Taiwan, R.O.C.
The information provided in this document is believed to be reliable. However, no
responsibility is assumed for any possible inaccuracies or omissions. pecifications
notice. The Windows 2000/XP/Vista
/7/8
are registered
trademarks of Microsoft. Other trademarks are the property of their respective
reserves the right to make changes without further notice to any products herein
LTT does not assume any liability arising out
of the application or use of any product or circuit described herein; neither does
it
convey any license under its patent rights, nor the rights of others.
Failure to follow instructions may lead to product damage, or error.
electric shock
.
invisible
radiation.
2
Contents
Introduction ............................................................................................... 1
Technical upport ..................................................................................... 1
Disclaimer ................................................................................................ 1
pecial ymbols ....................................................................................... 1
Chapter 1 Safety ....................................................................................... 4
1.1 afety Regulation .............................................................................. 4
1.2 Name Plate and Warning Labels .......................................................... 6
1.3 afety Protection Device ..................................................................... 8
Chapter 2 Installation ............................................................................. 10
2.1 Unpack and Locate Machine .............................................................. 10
2.2 Package Contents List ...................................................................... 11
2.3 Part Names and Functions ................................................................ 12
2.4 Hardware Installation ....................................................................... 19
2.5 Driver Installation ............................................................................ 21
2.5.1 Install Driver .......................................................................... 21
2.5.2 Uninstall Driver ....................................................................... 27
2.5.3 Change U B Cable to Another Port ............................................ 30
2.6 CorelDRAW etup ............................................................................ 32
2.7 AutoCad etup ................................................................................ 34
2.8 LTT Product Tools ............................................................................. 42
2.8.1 Install Procedure ..................................................................... 42
2.8.2 Uninstall Procedure ................................................................. 46
2.9 In- ight Explorer Installation ............................................................ 47
2.9.1 Install Procedure ..................................................................... 47
2.9.2 Uninstall Procedure ................................................................. 50
2.10 AutoCCD Installation ...................................................................... 51
2.10.1 Install Procedure ................................................................... 51
2.10.2 Uninstall Procedure ................................................................ 54
Chapter 3 Operation ............................................................................... 56
3.1 Operator Position ............................................................................. 56
3.2 Basic Operation Flow without CCD ..................................................... 57
3.3 Machine Operation without CCD ........................................................ 58
3.3.1 Control Panel .......................................................................... 58
3.3.2 Operating Menu ...................................................................... 61
3.4 Print Driver Operation ...................................................................... 68
3.4.1 Laser Tab ............................................................................... 68
3.4.2 Job Tab .................................................................................. 71
3.4.3 Page Tab ................................................................................ 73
3
3.4.4 Power cale ............................................................................ 75
3.5 LTT Product Tools Operation .............................................................. 76
3.5.1 ystem Upgrade ..................................................................... 76
3.5.2 Ethernet ettings Upgrade ........................... 77 錯誤
錯誤錯誤
錯誤! 尚未定義書籤
尚未定義書籤尚未定義書籤
尚未定義書籤。
。。
。
3.6 Basic Operation Flow with CCD .......................................................... 79
3.6.1 Calibration flow ....................................................................... 79
3.6.2 Operation Flow with CCD .......................................................... 81
3.7 AutoCCD Operation .......................................................................... 82
3.7.1 Controls ................................................................................... 82
3.7.1.1 Find the CCD IP address .................................................... 84
3.7.1.2 etup CCD IP address ....................................................... 85
3.7.2 CCD Monitor ............................................................................. 86
3.7.3 CCD Task Control ...................................................................... 87
3.7.3.1 Function description .......................................................... 87
3.7.3.2 etting Definition .............................................................. 89
3.7.4 CCD etting ............................................................................. 92
3.7.4.1 CCD shift and CCD Field Of View ......................................... 93
3.7.4.2 Position Test ..................................................................... 94
3.7.5 Communication etting .............................................................. 95
3.7.6 Tips of AutoCCD ........................................................................ 96
3.8 CCD Jobs Description ....................................................................... 97
3.8.1 ingle Pattern Job ..................................................................... 97
3.8.2 Two Pattern Job ........................................................................ 98
3.8.3 Circle Pattern Job .................................................................... 100
3.8.4 Calibration Job ........................................................................ 101
3.8.5 et the Default Job ................................................................. 102
3.8.6 Job Copy, ave and Delete ....................................................... 103
Chapter 4 Maintenance ......................................................................... 105
4.1 Daily Cleaning ............................................................................... 105
4.2 Weekly Cleaning ............................................................................ 107
Chapter 5 Trou le Shooting .................................................................. 109
Appendices ............................................................................................. 110
Appendix 1 pecifications ..................................................................... 110
Appendix 2 Dimensions ........................................................................ 111
Appendix 3 uggested Power and peed ettings ................................... 111
Chapter 1 Safety
Chapter 1 Safety
1.1 Safety
Regulation
The LC-M+
series uses a CO
product by
CDRH (the Center for Devices and Radiological Health)
Wavelength : 9.3~10.6µm
Maximum output power :
Visi ility : Invisi le
When operating the
with the safety regulations as following:
Do not attempt to modify or disassemble any component of the machine without
LTT
technical support
Do not open the doors of chassis and
components
Connect the machine to a grounded outlet. Verify that the voltage of the outlet
is correct for the machine.
Do not disable the interlocks which are on top and front doors.
Be careful about the path of t
eye or skin injury may result.
4
Chapter 1 Safety
Regulation
series uses a CO
2
Laser as a light source. It is classified as a class
CDRH (the Center for Devices and Radiological Health)
Wavelength : 9.3~10.6µm
Maximum output power :
17 ~ 100W
Visi ility : Invisi le
When operating the
SLC-M+
series, e sure to always comply
with the safety regulations as following:
Do not attempt to modify or disassemble any component of the machine without
technical support
.
Do not open the doors of chassis and
access the laser tube or electronic
components
, especially while the machine power is on.
Connect the machine to a grounded outlet. Verify that the voltage of the outlet
is correct for the machine.
Do not disable the interlocks which are on top and front doors.
Be careful about the path of t
he invisible laser beam shown in figure.
eye or skin injury may result.
Laser as a light source. It is classified as a class
-
IIIR
CDRH (the Center for Devices and Radiological Health)
.
series, e sure to always comply
Do not attempt to modify or disassemble any component of the machine without
access the laser tube or electronic
, especially while the machine power is on.
Connect the machine to a grounded outlet. Verify that the voltage of the outlet
Do not disable the interlocks which are on top and front doors.
he invisible laser beam shown in figure.
Otherwise,
Chapter 1 Safety
5
Do not watch the laser beam directly during operation. Bright light caused by
the lasing process can damage the eye.
The side and rear doors are fixed by screws for safety. If you open these doors,
the LC-M+ will become a Class 4 laser
device. For your safe, please wear
protective goggles.
The laser beam may cause fire. Never leave machine along without other
operator watching during the laser cutting process.
Keep a fire extinguisher near
the machine at any time.
Blowing materials with air flow from nozzle while cutting or engraving can avo
id
fire occurring and also obtain good quality.
Verify that materials used in the cutting are proper for lasing. Never cut
substrates that contain PVC or Teflon.
Good efficiency of exhaust system makes you avoid breathing dust, debris or
poison gas.
Please comply with maintenance schedule as chapter 4 to keep LC-M+
working
well.
Before you execute auto focusing function, please make sure that there will be
no crashing between motion system and other objects. For safety, it is NOT
recommended to use auto focusing function on inequality materials.
Chapter 1 Safety
6
1.2 Name Plate and Warning La els
The labels as following are affixed to the LC-M+
. These labels must never be
removed. If they are damaged or tampered for any reason, please request for
LTT
immediately to replace them.
1
2
3
4
L a s er To o l s & Te c h n i c s C o r p o r at i o n
Model No: SLC-M+ Serial No: 20150001
Specification: Vi60 220~240V 30A
Manufacture Date: 2015 .01
N o . 1 2 1 , L a n e 9 9 , P U
-
D I N G R O A D ,
H S I N C H U
C I TY, TA I W AN , R . O . C .
T E L : 8 8 6
-
3
-
5727772
FA X : 8 8 6
-
3
-
5728898
Chapter 1 Safety
7
5
Chapter 1 Safety
8
1.3 Safety Protection Device
Interlock
The laser beam will not be emitted if you open the front
door. The LED indicator of
“
DOOR” on control panel will be off.
Front door close
Front door opens
Laser Switch
Laser switch on control panel can shut down the power of laser system immediately
,
and it has no effect on motion system. Compared with interlock, Turning off laser
switch can save power. When you turn on laser switch, the LED indicator of
“
LASER
” on control panel will be on (it needs to take more than 5 seconds to warm
up laser tube while you turn it on).
ON
OFF
Chapter 1 Safety
9
Emergency Stop Switch
Pressing the red
pushbutton can shut down the main power of system immediately
when emergency condition occurs. And turning right the red
pushbutton can recover
the power (Before recovering power, please clear the trouble in the machine first).
ON
OFF
Chapter 2 Installation
10
Chapter 2 Installation
2.1 Unpack and Locate Machine
This section explains how to unpack and locate machine.
1. Locate the machine
and keep the recommended space for
maintenance.
Unit: mm
2. Lock the wheels to locate the machine.
Chapter 2 Installation
11
2.2 Package Contents List
This section explains the package contents of the LC. The package
includes the
following components. Before using the unit, check that all components have been
included in the package.
1 Box 5 LaserCAM Driver CD-Rom
2 Cotton Swa 6 USB Ca le Driver CD-Rom
3 Alcohol Dropper 7 Power Ca le
4 Allen Wrench
7
6
4
3
2
1
5
Chapter 2 Installation
12
2.3 Part Names and Functions
This section explains the main part names and functions of the LC-M+.
1. Front Door
This door has interlock sensors for safety. If you open this door, the laser will be not
emitted.
2. Front Door of chassis
Mostly opening this door is for maintaining. Do NOT
open this door if it’s not
necessary, especially the machine power is on.
3. Side Door (Left/Right) of chassis
Mostly opening this door is for maintaining. Do NOT
open this door if it’s not
necessary, especially the machine power is on.
1
2
3
3
Chapter 2 Installation
13
4. Exhaust Port
These two ports can exhaust the smoke
which is caused by cutting. These ports have
to be connected to blower through pipes.
5. Rear Door (Left) of chassis
Mostly opening this door is for maintaining. Do NOT
open this door if it’s not
necessary, especially the machine power is on.
6. Rear Door (Right) of chassis
Mostly opening this door is for maintaining. Do NOT
open this door if it’s not
necessary, especially the machine power is on .
7. Air Filter
These parts can dissipate the heat in the chassis which is caused by laser generator.
6
7
5
4
Chapter 2 Installation
14
8. Window Lens
This part can protect 1
st
~3
rd
mirror against dusts or
debris. It should be cleaned this
lens daily. ( ee chapter 4)
9. 4
th
Mirror
This part reflects laser beam to carriage.
Also, it should be cleaned this lens daily.
( ee chapter 4)
10. Ta le
This part can carry materials for cutting.
11. Carriage
This part includes 5
th
mirror, focal lens, nozzle, and auto focusing set. You can move
it left, right, forth and back by the keys on control panel. ( ee section 3.3.1)
8
9
10
11
Chapter 2 Installation
15
12. Final Mirror
This part reflect laser beam to focal lens.
Also, it should be cleaned daily. ( ee
chapter 4)
13. Focal Lens
This part can focus the laser beam on materials for cutiing.
Also, it should be cleaned
this lens daily. ( ee chapter 4)
14. Auto Focal System
This part can adjust focal height automatically by touching material.
15. Air Assist Adjustment
This part can adjust air flow which is out of the nozzle.
16. Nozzle
This part can provide a air assist to protect focal lens against dust or debris.
17. Real-time Exhaust
This part can
remove dust
immediately
12
13
15
14
16
17
Chapter 2 Installation
16
18. Emergency Stop
Please see section 1.3
19. Power Switch
This switch can turn on/off the main power of this machine.
20. Laser Power Switch
Please see section 1.3This switch can turn on/off the main power of this machine.
21. Ta le Suction On
Press this switch then the air of work table can be sucked.
22. Ta le Suction Off
Press this switch can turn off the air suck.
23. Run
Press this switch can start to run the work.
24. Reset
Press this switch can reset work.
25. Lcd Display
LCD display shows the operating menu and information from system. If you want to
obtain more detail about operating menu, please see section 3.3.1.
26. Control Panel
Control panel can
operate machine. If you want to obtain more detail about operating
18
24
23
22
21
20
19
25
26
Chapter 2 Installation
17
menu, please see section 3.3.1.
27.
Function Switch
This part provides user to switch the premissions by key switch.
Normal : Cutting without CCD function.
CCD : Cutting with CCD function.
Admin : Administration user with all function and close the interlock function.
*under the [Admin] permission, the machine will become a Class 4 laser
device. For
your safe, please wear protective goggles. (see section 1.1).
28. PC Power Switch
This switch controls the power of the built-in computer
, turn on the computer before
use the machine.
29. LED Light Switch
This switch controls the light inside the machine.
30. CCD Light regulator
This part control the CCD light, adjust it depending on using demand .
31. CCD Light Switch
This switch controls the CCD Light, turn it on before use the CCD function.
32. USB Port
This part can provide the U B ports to the built-in computer.
27
29
28
30
31
32
Chapter 2 Installation
18
33. Air Inlet Port
This part is the total air inlet for this machine.
34. Air Filter
This part filtered water vapor in the air is the total air inlet for this machine.
35. Oil mist separator
This part provide extra filtered for water vapor in the air. This part is the total air
inlet
for this machine.
36. Serials Port
This part is used for the expansion of I/O module.
37. RJ-45 Ethernet Port
LD-M+ provides built-in computer instead of external computer, it provides
computer Internet or LAN through this port.
38. Power Inlet
This part can provide main power through cable from wall power supply.
33
35
37
38
36
34
Chapter 2 Installation
2.4 Hardware Installation
This section explains the installation steps with other hardware.
1. Check environment
Power supply
Power supply : 220 VAC
Environment
Temperature:
15
Relative humidity : 35 ~ 85 %
Other : Avoid to dust, dirt, oil, mist, strong vibration, or sudden temperature changes
2. Connect AC power ca le
3. C
onnected
19
2.4 Hardware Installation
This section explains the installation steps with other hardware.
1. Check environment
Power supply
Power supply : 220 VAC
, ingle Phase
Environment
15
~ 30
℃
,
Relative humidity : 35 ~ 85 %
Other : Avoid to dust, dirt, oil, mist, strong vibration, or sudden temperature changes
2. Connect AC power ca le
onnected
the pipes from lower
to machine
This section explains the installation steps with other hardware.
Other : Avoid to dust, dirt, oil, mist, strong vibration, or sudden temperature changes
to machine
.
Table of contents
Other LTT Printer manuals
