LUIMOTO DL2 User manual

Thank you for purchasing Luimoto’s premiere product “TANK LEAF.”
The highest quality Tank Grips in terms of both look and feel in the market today!
TOOLS REQUIRED:
1. Isopropyl Alcohol
2. Soft Lint Free Cloth
3. Regular Tape or Double Sided Tape
4. Pen
5. Tape Measurer
6. Scissor6. Scissor
7. Printer
Typical Install duration: 1hr
Take your time, follow this guide, and be patient!
START
Step 1:
Print out this manual and read all the pages. Ensure it is printed at 100% ratio and not resized in anyway.
Step 2:Step 2:
In the following pages, take your scissor, cut along the outlines of the spacer squares and/or paper templates. (If applicable)
Step 3: VERY IMPORTANT
Spray Isopropyl alcohol onto a soft lint free cloth and clean all mounting surfaces on your motorcycle.
Ensure the mounting surfaces are dry, free of debris for proper adhesion.
WATCH OUR INSTALLATION VIDEO!
WWW.LUIMOTO.COM/VIDEOS
PRACTICE MOUNTING & TIPS!
Our guides are simply for your reference. Everyone may have a different mounting position or preference.
Before removing the 3M double sided tape, Practice positioning the Tank Leaf products on your bike. Ensure you get it at the right position.
You may use some regular tape to test your tank leaf positioning. Use your tape, pen, tape measurer, spacer squares and templates to help guide you
to ensure accurate positioning on your motorcycle.

CUT ME! SPACER SQUARES
PRE-BENDING
In some cases, Tank leaf might be positioned over a curve. It would help to pre-bend the product by hand for ease of installation.
SPACER SQUARES
These squares allow you to position the Tank Leaf in the recommended area accurately.
Cut them out, and tape them on the edges or lines of the bodywork if required by this instruction manual.
MOUNTING:
Carefully peel oCarefully peel off the backing paper from the 3M double sided tape, line up the Tank Leaf to the edges of the
spacer squares, and press down. Put firm pressure from the center and then out with your hands.
Press firmly and continuously all around for 30 to 50 seconds. Repeat steps for the other side.
Example of Right Side
TOP
RIGHT SIDE
MOUNTING ON: GAS TANK
TANK LEAF TYPE: KNEE GRIPS

TOP
BOTTOM
MOUNTING ON: GAS TANK
TANK LEAF TYPE: TANK PROTECTOR
IF YOU HAVE AN EXISTING TANK PROTECTOR TO REMOVE
IF YOU HAVE AN EXISTING TANK PROTECTOR, HEAT IT UP WITH A BLOW DRYER, AND USING YOUR FINGERS, PRY IT OFF.
SPRAY SURFACE WITH 3M RESIDUE REMOVER. FOLLOW THE MANUFACTURERS INSTRUCTIONS.
WHEN SATISFIED, FOLLOW UP WITH ANOTHER CLEAN UP WITH ISOPROPYL ALCOHOL TO REMOVE ANY
REMAINING OIL AND RESIDUE. FAILURE TO DO SO, THE NEW TANK PROTECTOR WILL NOT STICK ON PROPERLY.
MEASURING THE CENTER POINT
Take two pieces of tape and place it roughly where the bottom and top center
points are. Take your tape measurer and using the lines of your bike, find out
the center location for the top and bottom for your tank protector. Using a pen,
draw a center line on the bottom tape and the top tape.
PRE-POSITION
Pre-position your tank protector centered on your newly drawn center lines, Pre-position your tank protector centered on your newly drawn center lines,
does it look centered? If so, place a tape around 2” long on each side of the
tank protector for extra reference points.
PRE-BENDING
In some cases, the tank protector might be positioned over a curve. It would
help to pre-bend the product by hand for ease of installation.
MOUNTING
Carefully peel oCarefully peel off the backing paper from the grey 3M double sided tape and
press the Tank Protector down accurately and firmly in between the templates
and any additional reference points. Press continuously everywhere for 30 to
50 seconds.
reference
tape
Reference Photo Only
Not to scale
*TIP: Do not mount tank protector on any extreme creases and bends

TANK LEAF REMOVAL | Video: http://www.luimoto.com/tankleaf-removal
Do not use any sort of heat method as it will weaken the Tank Leaf internal structure. With a cold bike,
start from an edge and pull the product off with firm steady force using only your finger tips.
To remove the adhesive tape left on the gas tank, do not pull it up towards you as it will break and take a long time to remove.
With your fingers, simply pry up any corner, and pull it either up, down, left, or right alongside the motorcycle and repeat.
DOUBLE SIDED TAPE REPLACEMENT
YYou may purchase replacement 3M VHB double sided tape if needed.
Contact us at [e-mail] with your model name, year, and which replacement tape side you require.
Product Disclaimer
Motorcycling is an inherently dangerous activity, which may result in personal injury and/or death. Luimoto's products are designed to offer a great cosmetic upgrade to your motorcycle. Modifying parts on your motorcycle may be against the law in
your area. Please check your provincial/state law before using the product. Riders should always wear appropriate protective equipment when riding. Each individual rider should be familiar with the sport of motorcycling, recognize the wide range of
foreseeable hazards and decide whether to assume the risks inherent in such activitforeseeable hazards and decide whether to assume the risks inherent in such activity. MOTORCYCLE RIDERS MUST BE FAMILIAR WITH THE CAPABILITIES AND LIMITATIONS OF THE MOTORCYCLE AND THE EQUIPMENT THEY ARE USING.
Luimoto disclaims any responsibility for injuries incurred while using any of its products. In other words, use at your own risk.
WE HOPE YOU SINCERELY ENJOY YOUR TANK LEAF!
DON’T FORGET TO SHARE YOUR EXPERIENCE WITH US AND SEND US PHOTOS!
FOLLOW US
Post your experience, check out cool bikes and updates!
@luimoto
luimotoproducts
https://www.facebook.com/luimotoproducts/ https://www.instagram.com/luimoto/