Lumilum LUM-RGBUX8 User manual

Model: LUM-RGBUX8
INSTRUCTION MANUAL
*Optional

5Vdc, 0.5A~1A (with the included transformer)
RF 2.4GHz, DMX512
RGBW, 4 Zones Control
-30° ~55°
L132×W192×H50(mm)
230g
370g
Input Voltage:
Output Signal:
Control Mode:
Working Temp.:
Package Size:
Weight(N.W.):
Weight(G.W.):
Product Size:
Terminals UX8 RGB Touch Panel
Black Wire
Green Wire
White Wire
From the Female XLR
Back of Wall Panel
DMX Controller
LUM-B34XTS-DMX
Alternative Decoders
High Voltage (120V) Low Voltage (24V)
Alternative Decoders
RGB DMX
Hardwired Receiver
LUM-DMX212
RGB DMX Hardwired
Receiver (Water proof)
LUM-DMXWP2
For Model (LUM-B34XTS-DMX) and (LUM-B34XTS-WP2) a
Female Mini XLR to loose wire connector is required
(LUM-B34XTS-FXL) to connect to color wheel panel
Female Mini XLR to Loose
Model: LUM-B34XTS-FXL
Measures 50" in length

2 Use a straight screwdriver to pry the position shown:
1. Install the
Switch J-b ox into the wall. Typical boxes as below:
4 Connect in a right way and put the power adapter into the back box.
Installation Instructions
3. screw the baseplate and the back box in the wall firmly.
Transformer (Included)

5 Embed the upper touch panel into the base plate and then tap the
bottom to press into the slots.
Key Functions:
Touch Circle
Speed/Brightness +/-
White Key
Mode Key
Press: Turn on/
Long press:Dimming
Short press:play
Long press: save
Short press: on/select
Long press:
The Changing Mode (Press to Select ):
1. Static Red 2. Static Green 3. Static Blue 4. Static Yellow
5. Static Purple 6 . Static Cyan 7. Static White 8. RGB Jumping
9. 7 Colors Jumping 10 . RGB Smooth Transition
11. 7 Colors Smooth Transition
12. Static Black
Scene-mode keys
Zone Selection Keys

Application Composition
DMX512 Signal Output :
DMX Output Wiring
Low Voltage 24V Lumilum RGB Strip
001
005
009
DMX Output Wiring
Line Voltage 120V RGB Strip (B34XTS Series)
LUM-B34XTS-DMX
A C 1 0 0 ~2 4 0 V I n p u t
DMX GENERIC
CONTROL
PANEL
OR
RF TO DMX
MODULE
D +
D -
GN D
A C 1 0 0 ~2 4 0 V I n p u t
A C 1 0 0 ~2 4 0 V I n p u t
DMX CONTROLLER
Model: LUM-B34XTS-DMX
Black: V+ Red: Red Light Green: GreenLight White: Blue Light LED Output: 100-240 VDC / 500W
Operating Temp. -20°C - +50°C -4°F - +122°F Line VoltageInput: 100-240 VAC
XLR Mini FemaleOutput Connector
XLR Mini Male Input Connector 1: COMMON 2: DMX- 3: DMX+
DMX INPUT DMX OUTPUT
White: D+
Green: D-
Black: GND
ToConvert 3 Pin Mini XLR to 3Pin DMX use converter cable Model#:LUM-B34XTS-XLR
Endof Cable
1: COMMON 2: DMX- 3: DMX+ NOTE:FOR DMX INPUT CABLE
DMX CONTROLLER
Model: LUM-B34XTS-DMX
Black: V+ Red: Red Light Green: GreenLight White: Blue Light LED Output: 100-240 VDC / 500W
Operating Temp. -20°C - +50°C -4°F - +122°F Line VoltageInput: 100-240 VAC
XLR Mini FemaleOutput Connector
XLR Mini Male Input Connector 1: COMMON 2: DMX- 3: DMX+
DMX INPUT DMX OUTPUT
White: D+
Green: D-
Black: GND
ToConvert 3 Pin Mini XLR to 3Pin DMX use converter cable Model#:LUM-B34XTS-XLR
Endof Cable
1: COMMON 2: DMX- 3: DMX+ NOTE:FOR DMX INPUT CABLE
DMX CONTROLLER
Model: LUM-B34XTS-DMX
Black: V+ Red: Red Light Green: GreenLight White: Blue Light LED Output: 100-240 VDC / 500W
Operating Temp. -20°C - +50°C -4°F - +122°F Line VoltageInput: 100-240 VAC
XLR Mini FemaleOutput Connector
XLR Mini Male Input Connector 1: COMMON 2: DMX- 3: DMX+
DMX INPUT DMX OUTPUT
White: D+
Green: D-
Black: GND
ToConvert 3 Pin Mini XLR to 3Pin DMX use converter cable Model#:LUM-B34XTS-XLR
Endof Cable
1: COMMON 2: DMX- 3: DMX+ NOTE:FOR DMX INPUT CABLE
Up to 164ft. of 100-240V RGB LED STRIP
Up to 164ft. of 100-240V RGB LED STRIP
Up to 164ft. of 100-240V RGB LED STRIP
LUM-DMX212
LUM-DMX212
LUM-DMX212
LUM-DMX212
013
LUM-RGBUX8
LUM-RGBUX8
LUM-RGBUX8
LUM-RGBUX8
LUM-RGBUX8-RC
LUM-RGBUX8-WF
LUM-RGBUX8-WF LUM-RGBUX8-RC

DMX System Wiring
PS: No WiFi router needed when WiFi LUM-RGBUX8-WF is setup as network
*
1. Configure
smart phone to control the DMX device via WiFi LUM-RGBUX8-WF.
2. Configure V8 (LUM-RGBUX8-RC) which enables LUM-RGBUX8-RC
to control DMX device.
WiFi LUM-RGBUX8-WF with LUM-RGBUX8, which enables the
Match Code Sequence
Match / Clear Code for WiFi , UX8, V8
Match Code:
Clear Code:
Press within 5s, if
the indicator lights on panel stop
flickering, match successfully.
any key on V8
Press panel B within 5s,
if the indicator lights on panel A
stop flickering, match successfully.
any key on
Press
within 5s,
(The smart phone has already
any zone key on smart phone,
then touch the color bar
if the indicator lights on panel stop
match successfully.
matched with (LUM-RGBUX8-WF)
Press key on panel
for 3s, all the indicator
light flicker.
Press keys simultaneously on LUM-RGBUX8
for more than 6s, if all the indicator lights flicker
3 times,deactivate the matching successfully.
With V8 (LUM-RGBUX8-RC)
With (LUM-RGBUX8)
With WiFi
1
2
2
2
Lumilum
B34XTS App
LUM-RGBUX8-RC
LUM-RGBUX8
LUM-DMX212
24V STRIP
LUM-B34XTS-DMX
120V STRIP
with phones directly.
LUM-RGBUX8-WF
WiFi
(LUM-RGBUX8-WF)
flickering
RF Wireless Syncing