Luminox CHRONOGRAPH ALARM User manual

GGM.L003 Ed. 09.12
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
MANUAL DE USO
CHRONOGRAPH ALARM
www.luminox.com

Push button
Drücker
Pulsador
Crown
Krone
Corona
Hour hand
Stundenzeiger
Manecilla de
las horas
Minute hand
Minutenzeiger
Manecilla de
los minutos
Second hand
Sekundenzeiger
Manecilla de los
segundos
min
31
12
60
s ec
30
6
min
31
12
60
s ec
30
6
Chrono: Seconds
Chrono: Sekunden
Cronógrafo:
Segundos
Alarm + reference time
Alarm + Referenzzeit
Hora de despertador +
hora de referencia
Chrono: Minutes and
hours
Chrono: Minuten
und Stunden
Cronógrafo: Minutos
y horas
Date
Datum
Fecha
min
31
12
60
s ec
30
6
min
31
12
60
s ec
30
6

III III
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
III
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
Adjusting the chronograph
hands to zero position
Example:
One or several chronograph hands are not
in their correct zero positions and have to be
adjusted (e.g. following a battery change).
Pull out the crown to position III (all 3
chronograph hands are in their correct
or incorrect zero position.The display
changes from alarm time to reference
time.)
Keep push-buttons A and B depressed
simultaneously for at least 2 seconds
(the center stop-second rotates by
360° corrective mode is activated).
Center stop-second
Push-button B
Minute counter
Hour counter
Push-button A
Adjusting the center stop-second
Single step A1 x short
Continuous Along
Adjusting the next hand B
Adjusting the minute counter hand
and the hour counter hand
(mechanically coupled)
Single step A1 x short
Continuous Along
A
B
A
III
III
Returning the crown to position I
Termination of the chronograph hands adjustment
(can be carried out at any time). The display changes
from reference to alarm time.

Chronograph: Basic function
(Start / Stop / Reset)
Example:
Start: Press push-button A.
Stop: to stop the timing, press
pushbutton A once more and read
the 3 chronograph counters:
4h / 20 min / 38 sec
Zero positioning:
Press push-button B.
(The 3 chronograph hands will be reset to
their zero positions).
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
Note
The alarm cannot be used as long as the
chronograph is in operation.
Push-button A
Push-button B
Minute counter
Hour counter
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
30
10
20
12
3
6
9
12
2
4
6
8
1
01
11
3
5
7
9
15
60
30
45
21
21
Chronograph:
Accumulated timing
Example:
Start: (start timing)
Stop: (e.g. 15min 5sec following )
Restart:(timing is resumed)
*Stop: (e.g. 10 min 5 sec following )
=25 min 10 sec
(The accumulated measured time is shown)
Reset:
The three chronograph hands are returned
to their zero positions.
Push-button A
Push-button B
Minute counter
Hour counter
Please note:
* Following , the accumulation of the
timing can be continued by pressing
push-button A
(Restart / Stop, Restart / Stop, …)

30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
Push-button B
Minute counter
Push-button A
Push-button B
Chronograph:
Intermediate or interval timing
Example:
Start:(start timing)
Display interval:
e.g. 10 minutes 10 seconds (timing
continues in the background)
Making up the measured time:
(the 3 chronograph hands are quickly
advanced to the ongoing measured time).
Stop: (Final time is displayed)
Reset:
The 3 chronograph hands are returned to
their zero position
Please note:
* Following , further intervals or inter-
mediates can be displayed by pressing
push-button B (display interval / make up
measured time, ...)
*
III
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
01
01
III
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
31
31
Date 5130.B
Date 5130.D
Setting the date (quick mode)
Pull out the crown to positionII (the watch
continues to run).
Turn the crown until the correct
date
01
appears.
Push the crown back into position I.
Please note:
The date of the following day must be set in
the calendar changing phase between 9 PM
and midnight.
Setting the date too quickly in quick mode
can result in the incorrect date being
displayed. Switching the date between
01 and 31 (position II) restores the synchro-
nization.

IIIIII
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
04
04
IIIIII
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
04
04
Small
minute hand
Reference time
Reference time
Setting the reference time
* Pull out the crown to position III
(second hand stops. The display changes
from alarm time to reference time.)
Activating the setting mode.
Press the push-button for at least
2 seconds. As soon as the small minute
hand jumps forward one minute, this
mode is active.
Short pressing (less than 1 second):
the reference time is moved forward by
the minute.
Medium pressing: (1–2 seconds):
the reference time is moved forward by
the hour.
Long pressing (longer than 2 seconds):
the reference time is moved forward until
the push-button is released.
Please note:
* In order to set the time to the
exact second, must be pulled
out when the second hand is in
position «60» ().III
Once the hour and minute hands
have been set, must be pushed
back into position Iat the exact
second.
IIIIII
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
04
04
What is the reference time?
The current time is displayed by means of
the hour and minute hand.
Parallel to the current time, the reference
time runs in the background: the alarm time
refers itself to this reference time. Therefore,
resetting the time also requires the identical
correction of the reference time.
If the reference time is not synchronized
with the current time, this results in the alarm
signal being emitted at a different
time to the set alarm time.
Alarm time
*Push the crown back into position I
(the display changes from reference time
to alarm time).
A signal indicates that the alarm is
switched off.

I
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
31
31
Alarm time Push-button
Note
The alarm cannot be used as long as
the chronograph is in operation.
Setting the alarm time
Activate the setting mode
Press the push-button for at least
2 seconds. As soon as the small minute
hand jumps forward one minute, this
mode is active.
Setting
Short pressing (less than 1 second):
the alarm time is moved forward by the
minute.
Long pressing (longer than 2 seconds):
the alarm time is moved forward until the
push-button is released.
Please note:
If the push-button is not activated for
10 seconds, the setting mode of the alarm
time deactivates itself. At the same time,
two beeps are emitted to indicate that the
alarm is switched on.
I
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
31
31
Alarm time Push-button
Switching the alarm on / off
The alarm is switched on / off by briefly
pressing the push-button:
2 beeps alarm switched on
1 beep alarm switched off
Please note:
The alarm can be set a maximum of 12 hours
before the desired alarm time.
Once the set alarm time has been reached,
a signal is emitted for 20 seconds.
This signal is repeated after two minutes.
Following brief pressing of the push-button,
the signal is immediately switched off.

Deutsch
III III
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
III
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
Zentrumstoppsekunde
Drücker B
Minutenzähler
Stundenzähler
Drücker A
Ausrichtung der Chronograph-
zeiger auf Nullposition
Beispiel:
Einer oder mehrere Chronographzeiger sind
nicht in ihren korrekten Nullpositionen und
müssen ausgerichtet werden (z.B. nach
Batteriewechsel)
Krone in Position III herausziehen.
(Alle 3 Chronographenzeiger stellen sich
in ihre korrekte bzw. nicht korrekte Null-
position. Anzeige wechselt von Alarmzeit
zur Referenzzeit.)
Drücker A und B gleichzeitig während
mindestens 2 Sekunden drücken.
(Der Zentrumstoppsekundenzeiger dreht
um 360° Korrekturmodus ist aktiviert)
Ausrichtung der Zentrumstoppsekunde
Einzelschritt: A1 x kurz
Kontinuierlich: Alang
Nächsten Zeiger ausrichten B
Ausrichtung des Minutenzählerzeigers
und des Stundenzählerzeigers
(sind mechanisch gekoppelt)
Einzelschritt: A1 x kurz
Kontinuierlich: Alang
A
B
A
III
III
Krone in Position Izurückdrücken
Abschluss der Chronographzeiger-Ausrichtung.
(dies ist jederzeit möglich. Anzeige wechselt von
Referenz- zur Alarmzeit.)

30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
Chronograph: Grundfunktion
(Start / Stopp / Nullstellung)
Beispiel:
Start: Drücker Adrücken
Stopp:Um die Zeitmessung abzubrechen,
Drücker A nochmals drücken und die
3 Chronographenzähler ablesen:
4h / 20 Min. / 38 Sek.
Nullstellung:
Drücker Bdrücken.
(Die 3 Chronographenzeiger werden in
ihre Nullstellungen zurückgestellt).
Drücker A
Drücker B
Minutenzähler
Stundenzähler
Hinweis
Solange der Chronograph in Betrieb ist,
kann der Alarm nicht bedient werden.
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
Chronograph:
Aufaddierte Zeitmessung
Beispiel:
Start:(Zeitmessung starten)
Stopp: (z.B. 15 Min. 5Sek. nach )
Restart:(Zeitmessung wieder freigeben)
*Stopp: (z.B. 10 Min. 5Sek nach )
= 25 Min. 10 Sek.
(Aufaddierte Messzeit wird angezeigt)
Nullstellung:
Die 3 Chronographenzeiger werden in
ihre Nullpositionen zurückgestellt.
Drücker A
Drücker B
Minutenzähler
Stundenzähler
Hinweise
* Nach kann die Aufaddierung der
Zeitmessung fortgesetzt werden. Dies über
Drücker A
(Restart / Stopp, Restart / Stopp, …)

30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
21
21
Drücker B
Minutenzähler
Drücker A
Drücker B
Chronograph:
Zwischenzeitmessung
Beispiel:
Start:(Messzeit starten)
Zwischenzeit anzeigen:
z.B. 10 Min. 10 Sek. (die Zeitmessung läuft
im Hintergrund weiter)
Messzeit aufholen:
(die 3 Chronographenzeiger werden
im Schnelllauf auf die weitergelaufene
Messzeit nachgeführt.)
Stopp:(Endzeit wird angezeigt)
Nullstellung:
Die 3 Chronographenzeiger werden in
ihre Nullpositionen zurückgestellt.
Hinweise
* Nach können weitere Zwischenzeiten
angezeigt werden. Dies über Drücker B (Zwi-
schenzeit anzeigen / Messzeit aufholen, ...)
*
III
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
01
01
Schnellkorrektur Datum
Krone in Position II herausziehen.
(Uhr läuft weiter)
Krone drehen bis das aktuelle
Datum (Beispiel ) erscheint.
01
Krone zurück in Position Idrücken.
III
30
10
20
12
3
6
9
12
2
4
6
8
10 1
11
3
5
7
9
15
60
30
45
31
31
Hinweise
In der Kalenderschaltphase von 21:00 bis
24:00 Uhr muss das Datum des folgenden
Tages eingestellt werden.
Extreme Beschleunigung in der Schnellkor-
rektur kann zu einer falschen Datumsanzeige
führen. Durch Schalten des Datums von 01
bis 31 (Krone Position II) wird die Synchroni-
sation wieder hergestellt.
Datum 5130.B
Datum 5130.D