lumishore SUPRA SY225 User manual

SUPRA Mains Driver Integrated System
BEFORE YOU START
SUPPLIED PARTS
www.Lumishore.com
45-0079-Rev 5
Lumishore UK Unit 2, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |[phone] | [e-mail]
SUPRA Driver Installation and Operating Instructions
(Note: SUPRA Driver for use with SY 225, SY 250, SY 300,
SY310 and TRX 802 Lights)
• High Intensity LED light – Do not stare into the LED module at close proximity.
• Always ensure that the vessel’s power source is disconnected or isolated prior to installation
• A qualied professional should carry out both the electrical and mechanical installation. If in doubt please contact LUMISHORE.
refer to product support section
• The Driver supplies voltage and current to the Underwater lights. Under no circumstances should the light cable be cut and
connected directly to voltage
• Always use a suitable fuse or circuit breaker to protect the complete system. Each light to be individually fused.
• The light should be installed 6” - 10” (150-250mm) below the minimum load waterline.
• For best results install the lights between 2.5ft (0.8m) and 6.5ft (2m) apart.
• Never try to install or remove light with the vessel in the water.
• Lights should not be exposed to any temperatures in excess of 150°F (65°C). For example, next to hot engine components or
where exhaust emissions could be expelled onto the light while underwater
1
Congratulations! You have purchased a LUMISHORE advanced technology underwater light. Every care has been taken
to ensure your LUMISHORE lights and drivers arrives in perfect condition, so please enjoy the ultimate experience in
underwater lighting.
LUMISHORE high intensity underwater lights are designed for those owners who prefer the integrity of a Weld-in instal-
lation in a light that employs the most powerful, ecient and cost eective underwater LED lighting on the market
today. The LUMISHORE Weld-in lighting system is suitable for many sizes and types of watercraft, including Sports
Boats, Cruisers, Yachts and Super Yachts. LUMISHORE Weld-in LED lights come with a compact electronic driver module
to ensure trouble free operation for years to come.
Please read the following pages before attempting installation to ensure complete understanding of the
LUMISHORE LED lights.
Product
No
SY250
39-0167
SY 300 / 310
39-0168
SY225
39-0292
TRX 802
39-0170
SUPRA Mains Driver Part Numbers

Planning the Installation & Wiring Diagram
www.Lumishore.com
Lumishore UK Unit 2, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |[phone] | [e-mail] 2
TYPICAL INSTALLATION
90 - 240 V
AC Mains
Light and
Light
cable
Mains
Driver
Function
Input (e.g.
switch,
dimmer,
etc)
The Supra Mains driver can be congured to give any combination of the following modes of operation (See
page 4 in this manual for instructions on how to connect the drivers to give the required functions).
Note : These instructions cover SUPRA White/Blue & SUPRA Cold White/Warm White depending on which are
being installed;
• Solid White / Cold White
• Solid Blue / Warm White
• Solid White / Cold White or Solid Blue / Warm White (Selectable via a switch)
• Strobe (via external input to the driver)
• Dimming (via external input to the driver)
For details on the light installation please refer to the light installation instructions.

Planning the Installation & Wiring Diagram
INSTALLING THE MAINS DRIVER
When Installing the drivers these instructions shall be followed:
• The driver should be mounted in an accessible area within reach of the light cable length supplied. Take
care to plan the cable route to the light
• The driver should be mounted to a at, insulating surface using the two mounting holes at either end
• The input voltage cable used should be a suitable marine approved mains cable
For details on the light installation please refer to the light installation instructions.
Input Voltage Range: 90-240VAC (50/60Hz)
Maximum Input Current: 2.1Amp
Input Wiring:
Brown Wire : LIVE
Blue Wire : NEUTRAL
Green/Yellow: EARTH
Function
Port
Light Port
www.Lumishore.com
Lumishore UK Unit 2, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |[phone] | [e-mail] 3
230mm
245mm
221mm
68mm
34mm 39mm

www.Lumishore.com
Lumishore UK Unit 2, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |[phone] | [e-mail]
Modes of Operation
4
OVERVIEW
The Supra Mains driver can be congured to give any combination of the following modes of operation:
• Solid White
• Solid Blue
• Solid White or Blue (Selectable via a switch)
• Strobe (via external input to the driver)
• Dimming (via external input to the driver)
HOW TO CONFIGURE THE DRIVER FOR WHITE ONLY or BLUE ONLY
The driver has two connections - one is for the light, and the other is
for the function port.
As supplied, the driver is set to come on in WHITE ONLY mode
(Jumper wires supplied connected to the function port). To enable
Blue only the jumpers need to be moved as shown below.
NOTE: If NO jumpers are connected the light will NOT come on.
NOTE: A cap is supplied with each driver for the function port. This
cap should always be tted unless replaced by a connector.
Function
Port
Light Port
2
1
7
6
5
4
8
3
WHITE / COLD WHITE ONLY
2 and 8
5 and 6
2
1
7
6
5
4
8
3
BLUE / WARM WHITE ONLY
3 and 8
5 and 6
Move Jumper Positions...
HOW TO FIT A SWITCH FOR WHITE / COLD WHITE AND BLUE / WARM WHITE SELECTION
Using the optional Switch Assembly (39-0146), and the supplied Y-Splitter Cable (24-0208), The Supra Mains driver can be congured
to work with an external switch to select between White / Cold White - O - Blue / Warm White. Field installable connectors are also
available to allow cable runs to be made to the correct length onsite. Contact Lumishore to discuss your requirements.
The switch requires an external power supply to be tted. Use a 12Volt DC power supply or the vessels 12Volt Battery. Allow a power
of 0.5 Watts per light.
Remove the Jumper wires and connect the supplied Y- Split cable into the function port, connect the switch assembly into the rst Y
split cable and then daisy chain the others together. Extension cables are available if required.
The diagram on the following page shows how the system connects together.
The switch assembly also allows for connection to a 3rd party 1-10volt dimming control and 3rd party Strobe input signal.

www.Lumishore.com
Lumishore UK Unit 2, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |[phone] | [e-mail]
Modes of Operation
5
I N P UT: 90-305VAC 2 .1A47/63Hz
AC L (B R O W N )
AC N ( B LU E )
( G R EEN /YE L LO W)
LED STATUS
x3: LIGHT TEMP
x5: NO LIGHT
BLINK: ATRBOK
Label PN:21-0214-REV-A Model No.HLG-185H-42B
AC-DC INTELLIGENT COMBI DRIVER
S E LV IP6 7
TÜV
Rhein la nd
Produc t Safety
BAUA R T
GEP R Ü F T TYPE APP R OV E D
:90°C :60°C
t t
c a
LIGHT CNCT
DIM CNCT
LUMISHORE PRODUCT CODE: CONFIGURED FOR:
MADE IN CHINA
90w
XX-XXXX
I N P UT: 90-305VAC 2 .1A47/63Hz
AC L (B R O W N )
AC N ( B LU E )
( G R EEN /YE L LO W)
LED STATUS
x3: LIGHT TEMP
x5: NO LIGHT
BLINK: ATRBOK
Label PN:21-0214-REV-A Model No.HLG-185H-42B
AC-DC INTELLIGENT COMBI DRIVER
S E LV IP6 7
TÜV
Rhein la nd
Produc t Safety
BAUA R T
GEP R Ü F T TYPE APP R OV E D
:90°C :60°C
t t
c a
LIGHT CNCT
DIM CNCT
LUMISHORE PRODUCT CODE: CONFIGURED FOR:
MADE IN CHINA
90w
XX-XXXX
I N P UT: 90-305VAC 2 .1A47/63Hz
AC L (B R O W N )
AC N ( B LU E )
( G R EEN /YE L LO W)
LED STATUS
x3: LIGHT TEMP
x5: NO LIGHT
BLINK: ATRBOK
Label PN:21-0214-REV-A Model No.HLG-185H-42B
AC-DC INTELLIGENT COMBI DRIVER
S E LV IP6 7
TÜV
Rhein la nd
Produc t Safety
BAUA R T
GEP R Ü F T TYPE APP R OV E D
:90°C :60°C
t t
c a
LIGHT CNCT
DIM CNCT
LUMISHORE PRODUCT CODE: CONFIGURED FOR:
MADE IN CHINA
90w
XX-XXXX
I N P UT: 90-305VAC 2 .1A47/63Hz
AC L (B R O W N )
AC N ( B LU E )
( G R EEN /YE L LO W)
LED STATUS
x3: LIGHT TEMP
x5: NO LIGHT
BLINK: ATRBOK
Label PN:21-0214-REV-A Model No.HLG-185H-42B
AC-DC INTELLIGENT COMBI DRIVER
S E LV IP6 7
TÜV
Rhein la nd
Produc t Safety
BAUA R T
GEP R Ü F T TYPE APP R OV E D
:90°C :60°C
t t
c a
LIGHT CNCT
DIM CNCT
LUMISHORE PRODUCT CODE: CONFIGURED FOR:
MADE IN CHINA
90w
XX-XXXX
AC INPUT 90 - 240v
Brown = Live, Blue = Neutral & Green/Yellow = Ground
TO LIGHTTO LIGHTTO LIGHTTO LIGHT
8-Way Male
Connector 8-Way Female
Connector
Battery
or PSU
+12v
Battery
or PSU
GND
NB: If Strobe Input is Not used
Strobe Input Cable Must also be connected to
BLK GRN YEL
RED +V
+12V
-V
BLU
WHT
RED
1 - 10v
Dimming
Input
10m SUPRA AC/DC Switch
Assembly. PN : 39-0146
Length
1m
5m
Part Number
24-0209
24-0210
Extension Cables (Optional)
Contact Lumishore for extension cable field
installable connector options
SUPRA AC/DC Y Splitter
Cable. PN : 24-0208
12V Strobe
input

www.Lumishore.com
Lumishore UK Unit 2, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |[phone] | [e-mail]
Modes of Operation
6
How to Add 3rd party 1-10V for dimming control
1 to 10 V DC Dimmer Module
Suitable for LED Driver
How to connect a STROBE FUNCTION
The lights can be strobed using a 12V Switching Signal Generator. When the signal generator is switched ON the lights will come
ON, when the signal is switched OFF, the lights will switch OFF.
Remove the strobe input cable from the switch assembly and connect to a 12Volt Strobe / signal generator. Note when strobe
function is not in use the strobe input should be kept to +12volts
12 V DC
Signal Generator
Note: In this mode, when the lights are initially switched ON they will light up and wait for a signal. Once they receive this signal they will respond (NO signal =
OFF, Signal = ON). This will remain the case until the lights are switched o and on again using the switch.
1 - 10v
Dimming
Input
The Lights can be dimmed using a 3rd party 1-10volt dimming module. Connect the 1-10volts between the green and yellow wires
of the Switch assembly. Note: The dimming module must be a Current Sink Module with a capacity >10mA per light - do not use a
current source module or adjustable power supply!
Battery
or PSU
+12v
Battery
or PSU
GND
NB: If Strobe Input is Not used
Strobe Input Cable Must also be connected to
BLK GRN YEL
RED +V
+12V
-V
BLU
WHT
RED 12V Strobe
input
Battery
or PSU
+12v
Battery
or PSU
GND
NB: Remove Strobe Input from Switch Assembly
BLK GRN YEL
RED
+V-V
BLU
WHT
RED
1 - 10v
Dimming
Input
12V Strobe
input

www.Lumishore.com
Lumishore UK Unit 2, Technium 1, Kings Road, Swansea, SA1 8PH, UK | [phone] | [e-mail]
Lumishore USA 7137 24TH Court East Sarasota, Florida 34243 |[phone] | [e-mail] 7
Product Support
LED Status
No LED light on driver
Solid LED
Flashing 5 times
Meaning
No power to driver
Power On
Driver cannot detect light
Action to take / Things to check
Check fuse / breaker
Check connections
Check voltage at input to driver connections
Driver is receiving voltage and operating properly
Check the switch is operating correctly
Check power connection to light
Check the connection on the back of the light (if present)
If a light does not switch on, or function normally it should be disconnected from the power source
LUMISHORE Ltd warrants the lighting system to be free from defects in workmanship for a period of three
years, starting from the date of original purchase. Should your lighting system have a problem during this
period, please contact your dealer as soon as you become aware of the defect.
Misuse, abuse, improper installation, neglect, improper shipping, damage caused by disasters (e.g. re,
ood and lightning), installation by unqualied personnel, unauthorized repair or modication will void
this warranty. For the avoidance of confusion and doubt, non compliance with all installation, maintenance
and operating instructions in this document constitute non conformance with warranty terms.
Full warranty details are available at www.lumishore.com.
TESTING THE LIGHTS
The underwater lighting system should always be tested before the boat goes back in the water. Check that
each light comes on, and all lights change in sequence as per the system operation section above. See the
problem solving guide for advice on resolving any issues.
WARRANTY
TROUBLESHOOTING
In the event of one or more of the lights not lighting up then check the LED status on the driver. The LED
will either be continually ON (healthy), OFF (no power to driver) or ashing. Please refer to the table
below for what the number of ashes means and what action to take..
In the event of an issue then:
1. Check the operation of the light and driver with only that light and driver powered
2. If the light is still not operational then swap the driver with the ashing LED with a driver which is
known to be working and re-test the light
3. Test the driver with a known good light
4. This will determine if the issue is with the light or the driver
5. Record the serial numbers of both the light and the driver and contact your local dealer