Lumotech L05011i User manual

L05011i <840179i-v3 22-12-2008>
LEDlight 1
-
20VA
L 0 5 0 1 1 i U N I D IM 1 - 1 0 V , p u l s e
Gebruiksaanwijzing / Manual
NL
De L05011i ‘UNIDIM’ levert 3 spanningen (10V,12V,24V) en 3 stromen (350mA,
700mA, 1050mA). Eenvoudig te kiezen via dipswitches.
De Dimingang kan gestuurd worden door een standaard regelaar van 1-10V
(range 0-100%) een potmeter van 100K (range 0-100%) of een puls schakelaar
(range 3-100%). Door een korte puls kunnen de LED’s echter wel uit- en
aangeschakeld worden
De voeding is viervoudig beveiligd: thermisch, tegen kortsluiting aan de
secundaire zijde, tegen overbelasting en onbelast gebruik.
BELANGRIJKE INFORMATIE
1. De ‘LEDlight’ mag alleen door erkende installateurs gemonteerd worden!
2. Vóór montage de netspanning uitschakelen, ook als aan het secundaire
circuit gewerkt wordt!
3. LET OP: Controleer of de aan te sluiten LED units op stroom of spanning
werken! Bij verkeerd aansluiten kunnen deze stuk gaan!
4. De ‘LEDlight’ is alleen geschikt voor binnen gebruik!
5. Belast de driver nooit hoger dan 20W bij 230V en 15W bij 110V. Bij
overbelasting gaan de LED’s knipperen tijdens dimmen!
6. De output en 1-10V ingang zijn SELV en mogen niet met 110-240V
bekabeling gecombineerd worden.
Werking
GB
The ‘UNIDIM’ generates 3 output voltages (10V,12V,24V) and 3 different current
settings (350mA, 700mA, 1050mA). Easy adjustable through dipswitch settings.
For the DIM-input can be used: a standard 1-10V controller (range 0-100%), a
100K potentiometer (range 0-100%), or a pulse switch (range 3-100%). A short
pulse switches the LEDs on or off.
The ‘LEDlight’ has fourfold protection: Thermal; short circuit; over voltage and
open circuit.
IMPORTANT INFORMATION
1. The ‘LEDlight’ must be installed by qualified electricians only!
2. Switch off the power supply before installation, also when making any
change in the secondary circuit.
3. WATCH OUT: Check if the LED units to be connected are current or voltage
type! If incorrectly connected, they can be damaged!
4. The ‘LEDlight’ is intended for indoor use only!
5. Never connect more load than 20W at 230V (15W at 110V). If you do, the
LEDs will flicker while dimming!
6. The outputs and 1-10V input are SELV and may never be combined with the
mains-cables.
Operation
Dipswitch Instelling / Dipswitch Settings
Aansluitschema / Wiring diagram
! Always disconnect the mains of the driver before plugging or unplugging the LED’s !
Connection scheme for output Connection scheme for DIM input
When using more Drivers on one Dimmer (Potmeter only)
Specificaties
/ Specifications
NL
GB
netspanning supply
110
-
240V 50 / 60 Hz
uitgangsspanning/ vermogen output voltage/ power
230V: 10V/10W; 12V/12W; 24V/20W
110V: 10V/10W; 12V/12W; 24V/15W
uitgangsstroom output current
350mA (max. 32 Volt)
1
–
9 LED x 1 Watt (U
f
3.2V max)
110V:
700mA (max. 32 Volt)
1
–
8 LED x 3 Watt
(U
f
3.4V max)
Max.
10
5
0mA (max. 20V)
1
–
4 LED x 4 Watt
(U
f
4.
0
V max)
15VA
Ta Ta
-
20ºC



+
50
ºC
Tc Tc
85ºC
keurmerken approvals
CE
normen standard
EN61347
-
2
-
13
, EN62384, EN55015, EN61000
-
3
-
2, EN61547 ‘SELV
-
equivalent’
aansluiting Connector
Pri. H05RN
-
F 1 mm
2
Sec. 0,5 mm
2
-
0,75 m
m
2
Dim Dim
1
-
10V
external, puls
e
switch or 100K log. potentiometer
kleur color
Grau, grijs, grey
gewicht weight
105 g
afmetingen size
111 x 52 x
24
mm
Dim
Dim
n
100k Log.
n
Dim
Dim
example 4 drivers;
pot should be
100k/4=25k 22k
n Max 50 units

Lumotech Holland B.V
Celsiusstraat 20, Heerhugowaard
Tel: [phone]
Fax: [phone]
www.lumotech.com
1 / 2 16-06-2009
D-SPEC-L05011i_v4.doc
Product Specification
L05011i LEDlight 1-20VA UNIDIM
Description
The L05011i LEDlight has three current and three voltage settings. Currents: 350, 700 and 1050mA. Voltages: 10, 12 and 24V.
The Driver is dimmable with a standard 1-10V device, a potentiometer or with a pulse switch.
Input / Output
System Input Voltage Nominal
110-240Vac
Driver Efficiency
85%
System Input Voltage Range
110-240Vac
Power Factor
0.9C
System Input Frequency
50/60Hz
Nominal Line current
System Input Power
24W
Output current
350mA or 700mA or 1050mA
Output Voltage ripple
0.5V
Operating Voltage
(current setting)
Depending on forward voltage of
the LED, but 33V max.
Operating Voltage
(voltage setting)
Output / Power / Current
10V / 10W / 1A
12V / 12W / 1A
24V / 20W /0,83A on 110V: 15W
Output power (current setting)
240V: 20 Watt (max.)
110V: 15 Watt (max.)
Approvals
CE, KEMA KEUR, ENEC-05
Immunity
EN 61547
EMI/RFI
EN 55015
(Conducted disturbance)
EN 61000-3-2 (Harmonics & crest limits)
Performance
EN 62384
Safety
EN 61347
-
2
-
13
Load
LED type
Current and Voltage (U
nom
230-240VAC)
Thermal protection
Yes, against overheating
Number of LED’s at 350mA
9 U
f
3.2V Max.
Output current overshoot
No
Number of LED’s at 700mA
8 U
f
3.4V Max.
Output Isolation
Yes SELV EQ.: Yes
Number of LED’s at 1000mA
4 U
f
4.0V Max.
Noise Level
Dimmer type
1
-
10V
, potentiometer
or pulse switch (SELV EQ.)
Circuit Lifetime
Load Operating Frequency
PWM 230Hz
Ambient Temperature range (Ta)
0 +50ºC
Open Circuit Voltage
33Vdc
Max. Case temperature (Tc)
<85ºC
Short circuit protection
Yes
Storage Temperature range
-20 +50ºC
Open circuit protection
Yes
Failure Rate
Nihil
Overvoltage protection
Yes
RohS compliant
Yes
Load voltage Setting Time
(>90%)
1 sec.
Packaging
Potting
No
weight
105 gram
Leads Pri.
H05RN-F 1mm
2
Case color
grey, blue
Leads Sec.
0.1mm
2
– 0.5mm
2
Maximum case height
24mm
Lead Connection Method
Clamp
Maximum case width
52mm
Mounting Method
Screw
Maximum case length
111mm

Lumotech Holland B.V
Celsiusstraat 20, Heerhugowaard
Tel: [phone]
Fax: [phone]
www.lumotech.com
2 / 2 16-06-2009
D-SPEC-L05011i_v4.doc
Product Specification
L05011i LEDlight 1-20VA UNIDIM