Lutron Electronics RadioRA RA-REP User manual

English
P/N 044-014
Read all instructions completely before
installation.
Installation Instructions for
RF Signal Repeaters
Please Leave for Occupant
RF Signal Repeater
Model Number:
RA-REP, RB-REP
120/127VAC, 50/60Hz
Important Notes
1. Install in accordance with all national and local
electrical codes.
2. Operate in ambient temperatures between 0°C
(32°F) and 40°C (104°F). Note: Attics can
exceed 40°C (104°F).
3. Clean control with a soft damp cloth only .
Do not use any chemical cleaners.
4. All RadioRA®controls must be located within
30 feet of an RF Signal Repeater.
5. No more than 4 RF Signal Repeaters (1 Main,
3 Auxiliary) can be used in a system.
6. Typical straight line range from one Repeater
to another Repeater is 60 feet (18m). (See
diagram on page 2.)
7. Use only the AC adapter provided by Lutron
with your unit. Using an AC adapter not rated
at the following specifications could damage
the control and possibly overheat the AC
adapter.
• Input: AC 120/127V 50/60Hz
• Output: AC 9V/500mA Class 2
8. The range and performance of the RadioRA®
System is highly dependent on a variety of
complex factors such as:
• Distance between system components
• Geometry of the home
• Construction of walls separating system
components
• Electrical equipment located near system
components
9. Do not mix RadioRA®“A” and “B” frequency
products within the same system. Products
with different frequencies are not
compatible.
If you are unsure about how to layout your system,
or have any other questions, call the
Lutron
Technical Support Center
at [phone].
Possible Cause
• No power available to unit.
• Faulty power supply.
• Repeater not programmed.
(Refer to the Setup Guide
for programming
instructions)
Symptom
Repeater appears
not to be working.
Troubleshooting
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Made and printed in the U.S.A. 8/01 P/N 044-014 Rev. A
FCC Information
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by Lutron
Electronics Co. could void the user's authority to operate this equipment.
Installation Contents
System Layout
Where to place an RF Signal Repeater.
RF Signal Repeater Installation
Installing an RF Signal Repeater.
Operation
To activate and program an RF Signal Repeater, refer to
the enclosed RadioRA® Setup Guide.
MAIN
MODE
INSTALL
ADDRESS
SETUP
BEEP
FLASH
TESTING
AUXILIARY
MAIN
REMOTE
REPEATERMODE
INSTALL
ADDRESS
SETUP
BEEP
FLASH
TESTING
Limited Warranty
Lutron will, at its option, repair or replace any unit that is defective in
materials or manufacture within one year after purchase. For warranty
service, return unit to place of purchase or mail to Lutron at 7200 Suter Rd.,
Coopersburg, PA 18036-1299, postage pre-paid.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES,
AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS LIMITED TO
ONE YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER
THE COST OF INSTALLATION, REMOVAL OR REINSTALLATION, OR
DAMAGE RESULTING FROM MISUSE, ABUSE, OR IMPROPER OR
INCORRECT REPAIR, OR DAMAGE FROM IMPROPER WIRING OR
INSTALLATION. THIS WARRANTY DOES NOT COVER INCIDENTAL OR
CONSEQUENTIAL DAMAGES. LUTRON’S LIABILITY ON ANY CLAIM
FOR DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE
MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE
UNIT SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. Some states do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to
you. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply
to you.
This product may be covered under one or more of the following U.S.
patents: 4,835,343; 4,954,768; 5,248,919; 5,399,940; 5,637,930; 5,736,965;
5,798,581; 5,838,226; 5,848,054; 5,905,442; 5,982,103; DES 353,798; DES
378,814; DES 389,461; DES 389,805; DES 395,037; DES 404,013; DES
422,969; DES 428,855; DES 436,579, DES 439,220 and corresponding
foreign patents. U.S. and foreign patents pending. Lutron and RadioRA are
registered trademarks of Lutron Electronics Co., Inc..
© 2001 Lutron Electronics Co., Inc.
Technical Assistance
If you have questions concerning the installation or
operation of this product, call the Lutron Technical
Support Center. Please provide exact model number
when calling.
[phone] (U.S.A., Canada, and the Caribbean)
Other countries call [phone]
Fax [phone]
Visit our web site at www.lutron.com
®
Wireless Home Lighting Control

Optional Wall Mounting
The Repeater can be wall mounted using the supplied wall
bracket.
Attach wall bracket to wall using
the supplied screws and wall
anchors.
Wrap excess power supply cord
around the cord holder. Align
Repeater and snap onto wall
bracket.
UP
UP
RF Signal Repeater
Installation
Check off Steps as completed.
Step 1 Find a suitable location for the RF Signal Repeater.
Choose a discreet location that is centrally located to all
system controls. The Repeater must be located within 30
feet (9m) of all system controls or within 60 feet (18m) of
a previously installed Repeater.
Step 2 Attach the power supply cord to the Repeater (jack
located on rear of Repeater).
Step 3 Plug the other end of the power supply into a
120/127VAC, 50/60Hz wall receptacle.
MAIN
MODE
INSTALL
ADDRESS
SETUP
BEEP
FLASH
TESTING
AUXILIARY
System Layout
Each RF Signal Repeater will cover approximately a 2000 square foot
area.
This diagram shows a 3000 square foot home requiring two RF Signal
Repeaters.
All system controls must be within a 30 foot (9m) distance, in any
direction, of an RF Signal Repeater. Each repeater must be within 60
feet (18m) of another Repeater.
MAIN
REMOTE
REPEATERMODE
INSTALL
ADDRESS
SETUP
BEEP
FLASH
TESTING
30 ft. (9M)
Repeater
50 ft.
(15m)
30 ft. (9m
All system components
MUST be within this area.
MAIN
REMOTE
REPEATERMODE
INSTALL
ADDRESS
SETUP
BEEP
FLASH
TESTING
MAIN
REMOTE
REPEATERMODE
INSTALL
ADDRESS
SETUP
BEEP
FLASH
TESTING
60 ft. (18m)
maximum
All system controls
MUST be within this area.
30 ft. (9m)
Note: The Repeater's range is 30 feet in all directions.
MAIN
REMOTE
REPEATERMODE
INSTALL
ADDRESS
SETUP
BEEP
FLASH
TESTING
Multiple Repeaters
100 ft
(30m)
30 ft. (9m)
MAIN
REMOTE
REPEATERMODE
INSTALL
ADDRESS
SETUP
BEEP
FLASH
TESTING