LuxaFlex PowerView Motorisation User manual

PowerView™Motorisation
by LUXAFLEX®WINDOW FASHIONS
REMOTE CONTROL GUIDE

Your new PowerView™
Pebble® Remote and
Surface Remote combine
fashion with function for
precise control of your
LUXAFLEX®Window
Coverings. Artfully
designed, PowerView
remotes allow you to
control natural light
throughout your home
with the press of a button.
The following pages
provide all the details on
how to set up and operate
both remote styles.

Table of Contents
Key Components.................. 3
Getting Started ..................... 8
Programming....................... 11
Basic Operation..................20
Battery Replacement..........23
Troubleshooting..................27

Key Components
3

4
POWERVIEW™ PEBBLE® REMOTE
Ergonomically designed, the PowerView Pebble
hand-held remote is available in seven on-trend colours to
complement your home décor.

5
POWERVIEW SURFACE REMOTE
The sleek PowerView Surface is wall-mounted so you
know your remote is always right where you left it.
KEY COMPONENTS

REMOTE MODULE FRONT
6
RIGHT ARROW
Function varies
with shade type.
LEFT ARROW
Function varies
with shade type.
Favourite
Shade position
STOP
Press and
hold for
program
mode.
GROUP 1
GROUP 2
GROUP 3 GROUP 4
GROUP 5
GROUP 6
CLOSE
OPEN
KEY COMPONENTS

REMOTE MODULE (BACK COVER REMOVED)
7
BATTERY
COMPARTMENT
3V CR 2032
BATTERY
COMPARTMENT
3V CR 2032
RESET
BUTTON
KEY COMPONENTS

8
Getting Started

Important: The PowerView Remote will not operate a
window covering until the window covering has been added
to a GROUP.
Getting started
First, activate the remote by pulling both plastic tabs from the
back battery compartment.
Inserting the remote module into the PowerView Pebble®
(hand-held):
1. Centre the Hunter Douglas logo on the remote module
above the indentation on the bottom rim of the Pebble.
2. Align the ribs on the remote module with the grooves on
the Pebble.
3. Gently push the remote module into the Pebble until it
is snug.
9
GETTING STARTED
Ribs on remote
to be aligned
with the
grooves on
the Pebble.
Centre logo

10
GETTING STARTED
Mounting the PowerView Surface:
1. Choose a location to mount the Surface.
2. Orient the Surface mounting plate so that the
Hunter Douglas logo is horizontal and level.
Mark screw holes.
3. If you are mounting the Surface onto drywall, use a
6mm drill bit to drill pilot holes. Tap drywall anchors into
the pilot holes until the flange of the anchor is flush
with the drywall.
4. If you are mounting the Surface onto wood, use a
3mm drill bit to drill the screw holes.
5. Attach the Surface mounting plate using the screws
provided.
6. Align the Surface ring with its mounting plate and twist
the Surface ring clockwise to lock it in place.
Inserting the remote module in the Surface:
1. Align the ribs on the remote module with the grooves
on the Surface.
2. Gently push the remote module into the Surface until
it is snug.
Ribs on remote
to be aligned
with the
grooves on
the Pebble®.
Centre logo

Programming
11

IMPORTANT: Is this your first remote? If so, continue
reading for programming steps. If you have already installed
a PowerView Hub or additional remotes, refer to page 17 for
more information.
A GROUP can be a single window covering or multiple
window coverings. There are six unique assignable
GROUPS to use on each remote. A window covering may
be assigned to more than one GROUP.
NOTE: It is recommended that only similar window
coverings be included in a GROUP because of differences
in product features and operation. When a window
covering is added to a GROUP for the first time, it is also
added to the PowerView Shade Network that links window
coverings and devices together.
Join a window covering to a GROUP
1. Press and hold STOP for 4 seconds to put the
remote in program mode. The backlit buttons on the
remote will flash to indicate it is in program mode.
2. Press the desired GROUP number (1– 6) on the remote.
The backlit GROUP number will flash to show it is
selected.
3. Press and hold the manual control button on the
window covering.
4. While continuing to press the manual button, press
OPEN on the remote. The window covering will
move slightly to indicate it has been joined to the
GROUP. Release the manual control button.
5. Press and hold STOP for 4 seconds to exit program
mode. The lights will stop flashing.
12
PROGRAMMING

13
Remove a window covering from a GROUP
1. Press and hold STOP for 4 seconds to put the
remote in program mode. The backlit buttons on the
remote will flash to indicate it is in program mode.
2. Press the desired GROUP number (1– 6) on the remote.
The backlit GROUP number will flash to show
it is selected.
3. Press and hold the manual control button on the
window covering.
4. While continuing to press the manual button, press
CLOSE on the remote. The window covering will
move slightly to indicate it has been removed from
the GROUP. Release the manual control button.
5. Press and hold STOP for 4 seconds to exit program
mode. The lights will stop flashing.
PROGRAMMING

Set a FAVOURITE position
Each window covering has one FAVOURITE position,
which is set at 50% open by default. Setting a new
FAVOURITE position overwrites any previous setting.
1. Open or close the window covering to the desired
position.
2. Press and hold STOP for 4 seconds to put the
remote in program mode. The backlit buttons on the
remote will flash to indicate it is in program mode.
3. Press and hold the manual control button on the
window covering.
4. While continuing to press the manual control button,
press ♥FAVOURITE on the remote. The window
covering will move slightly to indicate it has set this
window covering position as your FAVOURITE. Release
the manual control button.
5. Press and hold STOP for 4 seconds to exit program
mode. The lights will stop flashing.
14
PROGRAMMING

Pairing additional remote(s) to the
PowerView Shade Network
Follow these steps to copy the PowerView Shade Network
I.D. from the original remote to additional remotes. All
remotes in a home should be added to the same PowerView
Shade Network. This allows for easy installation of additional
control options, such as the PowerView Hub and PowerView
Repeaters. Remotes paired to the same network will be able
to operate the specific window coverings they are assigned
to.
1. Remove the back cover from the new remote.
2. Press and hold the recessed Reset button for 6
seconds, until the GROUP buttons flash twice. The
backlit buttons on the remote will flash to indicate the
remote is in learning mode. Reinstall the back cover.
3. Press and hold STOP for 4 seconds on the original
remote to put the remote in program mode. The
backlit buttons on the remote will flash to indicate
it is in program mode.
4. Press and hold the STOP button on the new
remote while pressing and releasing STOP on
the original remote.
5. The backlit GROUP buttons on the new remote will
flash twice to indicate the Shade Network I.D. has
been copied.
6. Press and hold STOP for 4 seconds on the original
remote to exit program mode. The lights will stop
flashing.
15
PROGRAMMING

16
Pairing PowerView Repeaters to a remote
created PowerView Shade Network.
Repeaters extend the range of the radio frequency (RF)
signal emitted by the PowerView Pebble® Remote, the
PowerView Surface, or the PowerView Hub when used with
the PowerView App.
1. ASSEMBLE the Repeater Kit by INSERTING the USB end
of the PowerView Repeater into the USB port of the USB
Power Supply.
2. PLUG the Repeater Kit into an electrical outlet, with
the Repeater facing up.
NOTE: A green light will illuminate on the Repeater
indicating it is receiving power and ready to join a
network.
3. PRESS and HOLD STOP on the PowerView Pebble
Remote until indicator lights on the interior of the remote
blink to put the remote in programming mode.
Hold the remote within 3 feet of the Repeater to complete
Step 4.
4. PRESS STOP on the remote.
NOTE: The green light will turn off, indicating it has been
joined to the network.
5. PRESS and HOLD STOP on the remote until the
indicator lights stop blinking.
PROGRAMMING

17
Pairing remote(s) to a PowerView Hub
created PowerView Shade Network.
A Hub previously paired to an existing remote created
PowerView Shade Network or that had created its own
network during setup, can have additional Pebble® or Surface
remotes paired to it, even if the remotes are introduced after
the initial Hub setup.
1. REMOVE the back cover on the remote module.
2. Using a ballpoint pen, PRESS and HOLD the recessed
Reset button for 6 seconds.
NOTE: The Group Numbers (1-6) will flash twice on
the PRESS of the reset button followed by three times
at six seconds.
3. HOLD the Remote module within approximately
12 inches of the Hub.
Complete Steps 4 and 5 at the same time.
4. PRESS and HOLD the STOP button on the remote
module.
5. PRESS and hold the button on the back of the Hub
for approximately 3 seconds.
NOTE: The Group Numbers (1-6) will flash to indicate
that the remote module has been networked to the Hub.
P
PROGRAMMING

Creating a Duplicate Remote
A duplicate remote will operate the same set of window
coverings and GROUPS as the original remote.
1. Remove the back cover from the new remote.
2. Press and hold the recessed Reset button for 6 seconds,
until the GROUP buttons flash twice. Reinstall the back
cover.
3. Press and hold STOP for 4 seconds on the original
remote to put it in program mode. The backlit buttons on
the remote will flash to indicate it is in program mode.
4. While pressing and holding ALL on the new remote,
press and release STOP on the original remote.
5. The backlit GROUP buttons on the duplicate remote will
flash twice to indicate all of the information from the
original remote has been copied.
6. Press and hold STOP for 4 seconds on the original
remote to exit program mode.
Deactivating the remote(s) auto-wake
feature.
The auto-wake feature activates the backlights on the
remote, whenever the remote is handled. This feature is
useful for immediately seeing which shade group buttons
were activated last, but deactivating this feature will help to
conserve battery life.
1. PRESS and HOLD the Group 6 button on the remote for
approximately six seconds.
2. The Group numbers (1-6) will blink once to indicate the
auto-wake feature has been disabled.
18
PROGRAMMING

19
What’s the Difference?
Paired remote Cloned remote
Same PowerView Shade
Network I.D. as original remote.
Same PowerView Shade
Network I.D. as original
remote.
Can be programmed differently
from original remote.
An exact duplicate of
original remote.
Can control a different set of
window coverings and/or
different GROUPS.
Must control the same
set of window coverings
and/or GROUPS.
Resetting window covering programming
This reset erases all programming stored in the window
covering, including GROUP assignments, preventing any
input device from operating the window covering. Its primary
use is during installation to correct GROUP and Network
assignments. This reset does not affect travel limits.
1. Press and hold the manual control button for 12 seconds.
The window covering will move slightly once after 6
seconds, then again after 12 seconds. Release the button.
2. Refer to “Join a window covering to a GROUP” on
page 14 to program the window covering to a group.
PROGRAMMING