Luxair LA-60-1100 STD User manual

To avoid the risk of accidents
or damage to this appliance
It is essential to read these
Instructions before it is installed ©® copyright luxair UK Ltd 2007
and
used for the first time.
Operating and installation instructions
All models:
Directions For Use

2
Contents
Caring for the environment____________________________3
Warning and safty___________________________________4
Warning and safty___________________________________5
Warning and safty___________________________________6
Warning and safty___________________________________7
Warning and safty___________________________________8
Removing transit screws______________________________9
Ducting reqirements_________________________________10
Cutting down chimney sections________________________11
Minimum and maximum height requirements_____________12
Non vented hoods___________________________________13
Checking your goods________________________________ 14
Checking your goods________________________________ 15
Installation for STD, RND, OC hoods___________________ 16
Installation for STD, RND, OC hoods___________________ 17
Installation for STD, RND, OC hoods___________________ 18
Installation for STD, RND, OC hoods___________________ 19
Installation for STD, RND, OC hoods___________________ 20
Installation for STD, RND, OC hoods___________________ 21
Installation for CVG, ST, hoods________________________ 22
Installation for CVG, ST, hoods________________________ 23
Installation for CVG, ST, hoods________________________ 24
Operating instructions all models_______________________ 25
Installation for OC hoods_____________________________ 26
Installation for OC hoods_____________________________27
Installation all Island hoods_________________________ 28 31
Changing the bulbs all models_______________________32 -33
Problem solving all models_________________________34 –38
Remote control operated hoods_________________________39
Luxair help line_____________________________________ 40
Cleaning and care________________________________41 – 42
Hood heights maximum and minimum___________________ 43
Warranty Form ________________________________44
Technical specifications______________________________ 45

3
Caring for the environment
Disposal of the packing
material
The transport and protective packing
has been selected from materials, which
are environmentally friendly for
disposal, and can normally be
recycled.
Packaging e.g. cling film, polystyrene
and plastic wrappings must be kept out
of the reach of babies and young
children. Danger of suffocation!
Disposeoforrecycleallpackaging
materials safely as soon as possible.
Ensure that electrical current is
switched off to the appliance until
after maintenance or repair work has
been carried out
by a suitably qualified engineer or
electrician. Domestic repairs or
attempted repairs will void the
warranty.
Disposal of your old appliance
Electrical and electronic appliances
often contain materials that, if
handled or disposed of incorrectly,
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of your
old appliance with your household
waste.
Please dispose of it at your local
community waste collection / recycling
center and ensure that it presents no
danger to children while being stored
for disposal.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person. If connected by a
plug, the plug must be rendered
useless and the cable cut off directly
Behind the appliance to prevent
misuse. See the "Warning and Safety"
The warranty of this appliance is not
transferable to another party, i.e.: when
another person or persons moves into a
property where the appliance is already
installed. However if the home is of a
new build and has been installed as
part of the new home then the warranty
is valid by the home builder and a valid
receipt should be obtained from them
up on completion of sale.

4
Warning and Safety instructions
This appliance complies with all
relevant legal safety requirements.
Inappropriate use can, however,
lead to personal injury and damage
to property.
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time. They
contain important information on the
safety, installation, use and
maintenance of the appliance.
Keep these instructions in a safe
place and ensure that all users are
familiar with the contents. Pass them
on to any future owner of the
appliance.
Correct usage
This appliance is intended for
domestic use only.
Luxair cannot be held liable for
damage caused by improper or
incorrect use of the appliance.
Warranty is not valid if installed in
the following locations.
Pubs.
Clubs.
Restaurants or cafes.
Schools.
Business restaurants or buildings or
used for commercial gain.
Technical safety
Before connecting the appliance
to the mains supply, make sure
that the connection details given
on the data plate correspond with the
on-site electricity supply; otherwise
the appliance could get damaged.
Consult a qualified electrician if in any
doubt.
The electrical safety of this
appliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system that complies with local and
national safety regulations. It is most
important that this basic safety
requirement is present and regularly
tested, and where there is in any doubt,
the household wiring system should be
inspected by a qualified electrician.
The manufacturer cannot be held liable
for the consequences of an inadequate
earthing system (e.g. electric shock).
Installation, maintenance and
repair work may only be carried out
by a suitably qualified and competent
person in strict accordance with
national and local safety regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorized work.

5
Warning and Safety instructions
The appliance is only completely
isolated from the electricity supply
when:
– It is switched off at the wall socket
and the plug withdrawn,
– The fuse from the fused spur
connection unit is withdrawn,
– The mains fuse is withdrawn, or
– Thescrew-out fuseisremoved(in
countries where this is applicable).
Do not connect the appliance
to the mains electricity supply by
an extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
In countries where there are areas
which may be subject to
infestation bycockroachesorothervermin,
payparticular attention to keeping
the appliance and its surroundings in
a clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the guarantee.
Never use an open flame
beneath the cooker hood. To
avoid the danger of fire, do not
flambé or grill over an open flame
under the cooker hood. When switched
on, the cooker hood could draw flames
into the filter. Fat particles drawn into
the cooker hood present a fire
hazard.
When using the cooker hood over a
gas hob, ensure that any burners in use
are always covered by a pan. The
burner should be switched off before
taking a pan off the hob, even for
brief periods.
Regulate the flames so that they do
not extend beyond the base of the pan.
If flames are not covered by a pan
excessive heat can build up in the
cooker hood with the risk of damage to
the motor unit.
Always switch the cooker hood on when
a cooking zone is in use, otherwise
condensation may collect in the hood,
which could cause corrosion.
When cooking with oil or fat, chip
pans and deep fat fryers etc, do not
leave the pans unattended. Never leave
an open grill unattended when grilling.
Overheated oil and fat can ignite and
could set the cooker hood on fire.
Do not use the cooker hood without the
grease filters in place. This way you
will avoid the risk of grease and dirt
getting into the appliance and
hindering its smooth operation.
The grease filter should be
regularly cleaned. A saturated
filter is a fire hazard. See "Cleaning
and care”. For further information.
Do not use a steam-cleaner to
clean this appliance. Pressurised
steam could reach the electrical
components and cause a short circuit.
Never use spray cleaners directly
around the controls or buttons, this
could also cause damage to the
internal circuit board.

6
Warning and Safety instructions
Safety with children
This appliance is only intended for
use by adults who have read these
instructions it is not a toy! To avoid the
risk of injury, keep children well away,
and do not allow them to play with it or
use the controls. They will not
understand the potential dangers
posed by it. They should be
supervised whenever you are
working in the kitchen.
Please be aware that on
appliances with halogen lighting, the
lamps will get very hot during use and
remain hot for some time after
switching off. To safeguard against
burning, keep children well away from
the lamps at all times. For
instructions on changing bulbs,
please refer to maintenance sector
in this booklet.
Packaging e.g. cling film,
polystyrene and plastic wrappings must
be kept out of the reach of babies and
young children. Danger of suffocation.
Disposeoforrecycleallpackaging safely
as soon as possible.
Installation
The distance between the top of
the cooker/hob and the bottom of the
cooker hood canopy must measure at
least 365 mm, unless a greater
distance is specified by Luxair.
If more than one appliance is fitted
beneath the cooker hood, and they have
different minimum safety distances
to the cooker hood, select the greater
distance.
Safety regulations prohibit the
fitting of a cooker hood over solid fuel
stoves.
All ducting, pipe work and
fittings must be of non-flammable
material. These can be obtained from the
Luxair web site or from local builders'
merchants.
The appliance must not be
connected to a chimney or vent
flue, which is in use. Neither should it
be connected to ducting, which
ventilates rooms with fireplaces.
If exhaust air is to be extracted into a
chimney or ventilation duct no longer
used for other purposes, seek advice.

7
Warning and Safety instructions
Using at the same time as other
heating appliances that depend on
the air from the room
Warning - danger of toxic fumes
Great care should be taken when
using the cooker hood at the same
time and in the same room or area of
the house as another heating appliance,
which depends on the air in the room.
Such appliances include gas, oil, wood
or coal-fired boilers and heaters,
continuous flow or other water heaters,
gas hobs, cookers or ovens which draw
air in from the room and duct exhaust
gases out through a chimney or
extraction ducting.
When used in extraction mode, with or
without an external motor, the appliance
draws air in from the room in which it is
installed and from neighboring rooms. If
there is insufficient air, an
Under pressure will occur. The heating
appliance may be starved of oxygen,
impairing combustion.
Harmful gases could be drawn out of
the chimney or extraction ducting
back into the room, with potentially
fatal consequences.
In order to ensure safe operation, and
to prevent gases given off by the
heating appliances from being drawn
back into the room when the extractor
and the heater are in operation
simultaneously, an under pressure in the
room of 0.04 mbar (4 pa) is the
maximum permissible.
Ventilation can be maintained by air
inlets, which cannot be blocked, in
windows, doors and outside wall vents,
or by other technical measures, such
as ensuring that the extractor can only
be switched on when the heating
appliance is switched off or vice-versa.
A ventilation brick alone is not generally
sufficient to ensure safe ventilation.
The overall ventilation condition of
the dwelling must be taken into
account. If in any doubt, the advice
of a competent builder or, for gas, a
"Corgi" installer, must be sought.

8
Warning and Safety instruction
Important: To avoid the danger of toxic
fumes please observe the Warning
and Safety instructions. This is
especially crucial when using the
cooker hood at the same time as
another heating appliance, which
relies on air from the same room. The
cooker hood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
– All ducting, pipe work and fittings
must be of non-flammable materials.
– The exhaust ducting should be as
short and straight as possible.
– To ensure efficient air extraction, the
diameter of the exhaust ducting
should not be less than 125 mm.
If exhaust ducting with a diameter of
less than 150 mm, or if flat ducting is
used, the noise level of the cooker
hood will increase and extraction will
be less efficient.
Never reduce the diameter of the
ducting, e.g. where narrower ducting
has already been installed.
– Only use wide radius bends. Tight
bends reduce the air throughput of
the cooker hood.
– Only use smooth pipes or flexible
hosesmadefromnon-flammable
materials for extraction connection.
–If the exhaust air is to be ducted into
a vent flue, the ducting must be
directed in the flow direction of the
flue.
Warning:
Luxair will not exchange or repair
damaged hoods caused by incorrect
ducting being fitted, the minimum
ducting must not be smaller than
125mm. never use ducting previously
installed from your last extractor unit.

9
Warning Ducted out hoods
Please take notice of the following
All Luxair cooker hoods must be fitted with 125mm-150mm ducting, this
must not be reduced in any way for the entire length of its run, it must also
not exceed 3.5mtrs in length from the top of the motor housing connection
to the outside vent plate (applies to all wall mounted and island models).
125 or 150 mm ducting
Warning:
Luxair will not cover the warranty if you have installed the cooker hood on either,
100mm ducting, or an old or existing ducting used by a previous appliance.
Ducting must be fitted to
the out-side of the
reducer collar and
secured with a zip
fastener, also the ducting
must be aluminium and
conform to fire
regulations.
Kits can be purchased
form Luxair’s web site.
The minimum height
setting measuring from
the underside of the
extractor, to the top of the
gas hob is 750mm
And 650mm on electric
hobs, please note that
when using a hob larger
than 60cm please set the
minimum height to
750mm.

10
Cutting Down Chimney Sections
100mm
100mm
Luxair recommend that the
following procedure be carried out
by a qualified and competent
person, cutting the extended
chimney sections requires care and
should only be attempted by a
competent or qualified person.
It is recommended that the
maximum you can cut from the
chimney sections is 200mm, this
would be done as diagram above on
all wall mounted hoods, taking
100mm from the top section and
100mm from the bottom section
using Sharpe tin snips. Or electric
snipers.
Warning:
Luxair cannot be held liable for damage
caused by carelessness when modifying
the chimney sections; any modification
damage caused by modifying this
appliance is purely at your own risk.
Your statuary rights are not affected
When cutting down chimney sections
on Island hoods it is recommended that
the hood is taken to a professional
metal fabricator, they often have laser
cutting equipment that can make the
job easier, however if you attempt the
job directly then electric tin nibblers
should do the job. Follow instructions
opposite.

Ducting Kits
Fig 1
1.5 mtr Ducting kit
Fig 2
3.5 mtr Ducting kit
Ducting kits are used to vent you’re kitchen odors to the outside of the house, and we
recommend that only Luxair ducting kits are used with our products, this will also assure you
that the product’s warranty is not affected.
The 125mm system is designed to be used in conjunction with Cooker hoods and extraction
fans with a maximum output of 850m_ per hour.
All 125mm internal components are made from flame retardant Materials.
All wall outlets are UV stabilized. Please note that maximum extraction ducting length when
vented does not exceed 3.5mtrs on wall models and a max of 5.5 mtrs on island hoods.
NOT SURE THEN CALL VISIT OUR WEB SITE
WWW.LUXAIRHOODS.COM

12
Cooker hoods that are not to be vented to outside walls
Please note that if the hood is
not to be vented to an outside
wall, the top section of the hood
with the vents must be used,
this allows the filtered air back
into the room. Failure to do so
will result in the hood been
noisy and will cause it to
vibrate; this will also void the
warranty if this section is not
used when installed in
recirculation mode.
Note that when the hood is not
vented to an outside wall,
charcoal filters must be used in
conjunction with the above vent
system, image shows how to fit
the filters to a standard hood,
see page 21 and 23 for further
instructions and other models.
Fitting the filters on standard or round hoods is as follows.
Offer the round filter to the side of the motor housing, twist clockwise slowly
until you feel the filter sit, then twist clockwise until you feel it lock! Reverse the
process to remove. Please note that the charcoal filters will need replacing every
two months, failure to replace these filters will result in the warranty been void.
For replacement filters please visit our web site at
www.luxairhoods.com

13
1) Unpack the hood and inspect the goods carefully, please check for any cosmetic
damage before installation begins, Luxair will not accept liability for cosmetic
damage after the hood has been installed, if damage is found then please contact
the retailer from where the goods were purchased.
2) Check that all parts and fixings are packed in the box.
3) Do not remove any of the protective film until installation is complete, this will
help reduce any accidental damage and help prevent scratching.
4) Remove the metal Grease filters immediately after opening packaging and store
in a safe place, they will not be needed until installation is complete, this will
also ensure against accidental damage of the filters.
5) You must use either a ducting kit or charcoal filters with all Luxair hoods.
6) All filters and ducting kits can be purchased from our web
site.www.luxairhoods.com
Please Check the Following Points

14
Standard Wall Mounted Hoods, STD, RND, OC
1
2
3
4 6
5

15
STD/RND Parts to the appliance
1 Wall Bracket
2 Top Chimney Section with Vents
3 Bottom Chimney Section
4 Reducer
5 Main Body
6 fixing screws
Press the button 1 to start the fan running on low, then increase to level 2 or
3 depending on cooking levels.
When the fan runs at power level 1. The indicator lamp will illuminate Red.
To select a power level
1-3 Use the numbered controls to select the power level required.
3 controls = higher setting 1 control = lower setting
Depending on the intensity of the cooking vapors, levels I to 2 are usually
sufficient for normal cooking.
• Press the 0 control to switch the fan off.
The indicator lamp will go out.

16
Fitting Instructions Applies To All Wall Mounted Hoods
1
Position the cooker hood body
directly above your hob, make
sure that you comply with the
minimum height regulations set
out on page 10 and 12
2
Secure the main body of the
hood to the wall. Make sure
that the fixings are adequate for
the type of surface you are
fixing to.
Luxair provide some screws but
they may need changing
depending on the type of wall
you have, if you are in any
doubt then seek professional
advice.
3
Measure the desired height of
your chimney sections.
Measure the center of the main
body section of the hood and
then draw a straight vertical
line, place the metal u shaped
bracket at desired height center
to your line and secure the
bracket to the wall.

17
Fitting Instructions Applies To All Chimney Wall Hoods
4
Mark the height and position of your
ducting hole; this should be a
minimum distance from top o the
hood to the center of your hole
400mm, (see page 11).
Remove the hood of the wall before
drilling the ducting position; this will
stop any debris from falling into the
fan housing and avoid any damage.
5
Mark the height and position of your
fused spur socket position this so it’s
accessible, this should also be fused
with a 13amp fuse.
Remove the hood of the wall before
drilling for the electrics.
6
Remount the body section to the wall
and proceed to make all electrical and
ducting connections, make sure you
have complied with all safety
instructions as set out on page 3-11.

18
Fitting Instructions Apply To All Wall Mounted Hoods
7
Once all electrical and ducting has
being connected and tested proceed
to assemble the chimney sections,
place the bottom part of the
chimney into the body of the hood,
no fixings are required as the
grooves secure this part, slide the
top section into the bottom section
of the chimney, taking care not to
scratch this as you do so.
The vented top section can be
turned upside down if the hood is
ducted outside, this will hide the
vents that are unnecessary for
ducted out use. See page 12 for
more details on vented or
recirculated options.
8
Slide the top section into place over
the wall bracket, take care not to
scratch this as you do so, and secure
the top section to the bracket with
the two short screws provided.
Your new hood is now ready for
use.
Warning
Do not attempt to clean down your
new hood until you have read the
cleaning instructions on pages 41
and 42. Careless cleaning could bur
and scratch your new hood.

Operation
19
Fitting The Charcoal Filters
9
If it was not possible to extract
you new hood to an outside
wall you must now fit this
cooker hood with charcoal
filters, failure to do so will void
the warranty, filters must be
changed at least every two-
three months, this appliance
must not be used with out
filters if not ducted to an
outside wall. See page 10.
10
Metal grease filters are
designed to last the life of your
hood and can be purchase direct
from Luxair should they
become damaged. These filters
can be cleaned in your
dishwasher in the upright
position or by hand washing in
soapy hot water only.
11
Remove all the protective film
taking care not to damage your
new hood.

20
Curved Glass and Straight
Glass Wall Mounted Units
CVD-ST MODELS
1
2
3
4
5
6