LUXE BIDET Sophea User manual

Warranty:
12-Month Limited Warranty to the original buyer from date of purchase that the cabinets will be free from defects
in material and workmanship under normal use.
Installa�on Manual
Read manual prior to installa�on for important
informa�on about safety, installa�on, use, and
maintenance.
Follow instruc�ons for proper assembly.
Assemble on carpet free of debris to prevent
scratching. Do not subs�tute parts. Do not
over�ghten screws. Do not use if broken or
damaged.
Assembly should be carried out by a qualified
person. Incorrect assembly may lead to furniture
�p-over and may cause injury or damage.
Warning
Serious or fatal injury can occur from
furniture tip-over. To prevent tip-over,
permanently attach product to wall or
floor with included attachment parts.
Fastening components are included,
but consultation with specialized dealer
for advice on suitable screw systems
and fastening devices is recommended.
Safety recommendation:
• Place heaviest items in lowest drawers.
• Do not set heavy objects on top of product.
• Do not allow children to climb or hang on
drawers, doors, or shelves.
• Do not open more than one drawer at a time.
• Use of tip-over restraints may reduce, but not
eliminate, the risk of tip-over.
Use as intended. Inappropriate use may cause
injury or damage.

2
M4x16mm. M3.5x13mm.
M4x40mm.
M6x23mm.
#8x35
M4x50mm.
M5x50mm.
M4x16mm.
M4x25mm.
A CB D E
F G H J K
L M N O P
Q R S T
U V W X
Y Z
(1/4”*2”)
CAM SCREW x28 WOOD DOWEL x50
CAM LOCK NUT x26
FLAT HEAD
SCREW x14
FLAT HEAD
SCREW x28
PAN HEAD
SCREW x29
FLAT HEAD
SCREW x99
FLAT HEAD
SCREW x24
HEX HEAD
SCREW x5 BUMPER CARD x14 HINGE x10 LARGE
BRACKET x6
FLAT HEAD
SCREW x9
FLAT HEAD
SCREW x5 EXTENSION SLIDE x4
EXTENSION RAIL x4
L-WRENCH x1
OUBLE XPANSIOND E
NCHOR x12A FLAT WASHER x12
SPRING WASHER x12
HEX BOLT x12
L-BRACKET x3
16mm.
PLASTIC PLUG x9
CAM LOCK NUT x2
12mm. #6x35
WOOD DOWEL x2
PLASTIC
BRACKET x5
BB
LEG x5
AA
3
EE DROP DOWN
STAY L244 x1
FF
DOOR
BRACKET x1
SIDE
BRACKET x1
COVER DOOR
BRACKET x1
HOW TO USE CAM SCREW
Turn the Cam Screw or
gently tap until the
shoulder is against the
surface of the part.
Cam Lock Nuts
Push a Cam Lock Nut into
the part. The arrow in the
Cam Lock Nut must point
toward the hole at the
edge of the board.
Insert the Cam Screw into the
Cam Lock Nut. Tighten the Cam Lock Nut.
!Click
!Push
EE
FF
CC
CC DD
DD

4
Step 1
Step 2
(4 used in this step)
M3.5x13mm.
K
S T
FLAT HEAD SCREW
(4x)
AA
Cam Lock Nut
1
2
(4 used in this step)
M3.5x13mm.
K
S T
FLAT HEAD SCREW
6
6
Step 3
Step 4
5
(6x)
AA
CAM SCREW
M4x16mm.
(10 used in this step)
J
FLAT HEAD SCREW
PLASTIC
BRACKET x5
BB
36
7
4
8
(4 used in this step)
M4x50mm.
F
FLAT HEAD SCREW
(4x)
C
WOOD DOWEL
#8x35
M4x16mm.
(4 used in this step)
J
FLAT HEAD SCREW
4
8
6
5

Step 5
Step 6
6
M4x16mm.
(2 used in this step)
J
FLAT HEAD SCREW
(6x)
C
WOOD DOWEL
#8x35
B
(2x)
CAM LOCK NUT
Arrow
5
2
4
8
5
7
3
M4x16mm.
(4 used in this step)
J
FLAT HEAD SCREW
B
(2x)
CAM LOCK NUT
Arrow
6
(10x)
C
WOOD DOWEL
#8x35
1
7
8
Step 7
Step 8
7
B
(6x)
CAM LOCK NUT
Arrow
(6x)
C
WOOD DOWEL
#8x35
36
6
1
2
M4x16mm.
(20 used in this step)
H
PAN HEAD SCREW
L LEG x5
5
(5 used in this step)
M4x25mm.
R
FLAT HEAD SCREW
4
3

Step 9
Step 10
8
Z
(12 used in this step)
(1/4”*2”)
V
Y
W
X
1/4”x2”
Z
(3 used in this step)
L-BRACKET-3
(15 used in this step)
M4x16mm.
J
Z
FLAT HEAD SCREW
(3 used in this step)
L-BRACKET-3
2
(2x)
AA
Cam Screw
D
(2x)
Cam Lock Nut
Arrow
M4x40mm.
(6 used in this step)
G
FLAT HEAD SCREW
17
16
14
13
11
11
(2x)
E
#6x35
WOOD DOWEL
9
Step 11
Step 12
M4x40mm.
(6 used in this step)
G
FLAT HEAD SCREW
10
16
13
14
10
15
15
12
12 11
11
M4x40mm.
(8 used in this step)
G
FLAT HEAD SCREW

10 11
Step 13
Step 14
Step 15
Step 16
(6 used in this step)
M3.5x13mm.
K
S
FLAT HEAD SCREW
M6x23mm.
(3 used in this step)
M
U
HEX HEAD SCREW
L-WRENCH
910
M4x40mm.
(8 used in this step)
G
FLAT HEAD SCREW
21
21
22
19
20
S
(6 used in this step)
M3.5x13mm.
K
FLAT HEAD SCREW
M6x23mm.
(2 used in this step)
M
U
HEX HEAD SCREW
L-WRENCH
17
19
A) Attach drawer assembly to assembled unit:
Fit drawer glides of drawer assembly into
corresponding drawer glides of unit. Push
drawer all the way into the assembled unit. Test
the drawer by opening and closing a couple of
times to ensure it is attached.
Assembly is now complete.
B) To remove drawer assembly from
assembled unit:
Fully extend drawer assembly from unit. Locate
plastic tabs on left and right drawer glides. With
even pressure, simultaneously lift the left tab and
push down the right tab and pull the drawer from
the assembled unit.
left drawer
glide
right drawer
glide
left drawer
glide
right drawer
glide
(2 used in this step)
N
BUMPER CARD (2 used in this step)
N
BUMPER CARD

12
Step 17
Step 18
(4x)
M4x16mm.
(8 used in this step)
J
O
FLAT HEAD SCREW
HINGE 23
24
M4x16mm.
(16 used in this step)
J
FLAT HEAD SCREW
24
23
(4 used in this step)
N
BUMPER CARD
13
Step 19
Step 20
0-0.39 inch
23
(4 used in this step)
M4x16mm.
J
FLAT HEAD SCREW
CC
DD
EE
DOOR
BRACKET x1
SIDE
BRACKET x1
COVER DOOR
BRACKET x1
DROP DOWN
STAY L244 x1
FF
(6x)
C
WOOD DOWEL
#8x35
29
30
31
31

Step 21
Step 22
14
29
30
31
31
32
M4x50mm.
(6 used in this step)
F
FLAT HEAD SCREW
(4x)
C
WOOD DOWEL
#8x35
(6x)
AA
Cam Screw
B
(6x)
Cam Lock Nut
Arrow
32
28
27
15
Step 23
Step 24
M4x50mm.
(4 used in this step)
F
FLAT HEAD SCREW
(14x)
C
WOOD DOWEL
#8x35
B
(10x)
Cam Lock Nut
Arrow
(10x)
AA
Cam Screw
25
28
27
26
32
(3x)
P
LARGE
BRACKET
M4x16mm.
(9 used in this step)
H
PAN HEAD SCREW

(3x)
P
LARGE
BRACKET
(9 used in this step)
M5x50mm.
FLAT HEAD SCREW
Q
PLASTIC PLUG
16
Step 25
Step 26
(6x)
M4x16mm.
(12 used in this step)
J
O
FLAT HEAD SCREW
HINGE
34
33 35-
AA
17
Step 27
M4x16mm.
(24 used in this step)
J
FLAT HEAD SCREW
33
34
35
(6 used in this step)
N
BUMPER CARD

18
Step 28
34
33
35
19
29/03/22-0 920000328
• Mark the attachment point(s) with a
pencil at the appropriate height.
• Drill 5/16-inch (8mm) diameter hole(s)
through the wall at the height you
marked with pencil.
• Drive the plastic plug(s) into the hole(s),
using a hammer if needed
Drywall without available wood stud:
• Mark the attachment point(s) with a
pencil at the appropriate height and
positioned over wood stud(s).
• Drill 1/8-inch (3mm) diameter pilot
hole(s) into the wood stud(s), at the
height you marked with pencil.
Masonry:
• Mark the attachment point(s) with a
pencil at the appropriate height.
• Drill 5/16-inch (8mm) diameter hole(s)
2 and 3/4-inches (70mm) deep into
the wall at the height you marked with
pencil.
• Drive the plastic plug(s) into the hole(s),
using a hammer if needed.
Drywall or plaster with available
wood stud:
WALL ANCHORING GUIDE:
The hardware you should use to secure your
furniture to the wall depends on both the
type of furniture you have and your wall
material.
Type of Wall Material:
Using the guide below, identify your wall
material and the appropriate steps to take
for that wall material.