Luxlink OSM-6222-XY User manual

WARRANTY
All fiber optic transmission systems, products and accessories
manufactured by Liteway, Inc. and it’s subsidiaries are fully tested
prior to shipment and are warranted against defective materials
and workmanship for a period of five full years from the date of the
original shipment. Should a problem occur, a Return Material
Authorization Number (RMA) must be obtained from Liteway Inc.
at [phone] and the item returned to Liteway, Inc. 166
Haverford Road, Hicksville, NY 11801, USA, prepaid. Liteway Inc.
will then, at its option repair or replace the defective item.
Liteway, Inc. maximum liability under this warranty is limited to the
cost of the defective item only. No contingent liabilities of any kind
are either assumed or implied.
Any items returned to Liteway, Inc. that have been misused,
abused, damaged, modified, connected or adjusted in any way
contrary to the instructions furnished by Liteway, Inc. or repaired
by unauthorized personnel will not be covered by this warranty.
Any non-warranty repairs required will be quoted at the current
rate for such services.
Important Notices
CAUTION ! AVOID DIRECT EXPOSURE TO BEAM.
All –5, -7, -8, and -9 Models use laser diodes. These solid-state
laser diodes are located in the optical ports of these units. Laser
diodes produce invisible radiation that may be harmful to human
eyes. Never look directly into the optical port of any fiber optic
unit designed to operate with single-mode optical fiber.
NOT FOR LIFE SUPPORT SYSTEMS
Liteway, Inc. does not authorize or warrant any of its products or
accessories for use in critical life support systems or applications
of any kind.
© Copyright 2017 Liteway, Inc. 135024 Rev D
OPERATING INSTRUCTIONS
Optical Bypass Switch with Monitors
Models; OSM-6222-XY, OSM-7222-XY
The OSM-6222-XY and OSM-7222-XY are single-mode fiber optic
switches that are used to route optical signals. The optical path
through the units is purely optical; i.e. there is no optical to electrical
to optical conversion as a result there is no electrical loss or electrical
bandwidth limit on the fiber optic path. Under normal operation the
optical switch routes optical signals to and from local external
devices. In event of a loss of power, the unit automatically switches
to bypass mode.
Technical Specifications
Switching Time < 10 ms
Back Reflection < -50dB
Insertion Loss < 1.1 dB
Cross-talk < -50dB
Mechanical Life > 1 Million cycles
Electrical Connector Removable terminal block
Temperature Range -35º to +70ºC
Operating Power Requirements -20 to -60 VDC (Positive ground)
Physical Size (mm) OSM-6222 5.0”(127)L x 1” (25.4)H x 3.0”(7)D
Physical Size (mm) OSM-7222 19”(483)L x1.75” (44.5)W x 6.0”(152)D
Specifications are subject to change without prior notice.
"XY" in the part number indicates the following"
X = Fiber/Connector: -1 = Multimode/ST, -2 = Multimode/LC,
-5 = Single-mode/SC, -6 = Single-mode/LC,
-7 = Single-mode/FCPC
Y = Signal/Monitor Version: -1 = 95/5, -2 = 90/10, -3 = 80/20,
-4 = 70/30
Note that the OS-6222-XY is intended for stand-alone or DIN rail
mounting with an optional DIN-1000 bracket. The OSM-7222-XY is
intended for standard 19 inch rack enclosure mounting.
!

West (left)
In 70 30
Tap W
Loop In
Rx Out
Tx In
Loop Out
East (right)
East mid
(right)
East (left)
In 70 30
Tap E
Loop In
Rx Out
Tx In
Loop Out
West (right)
West mid
(right)
Switch 1
Switch 2
Splice
Splice
West mid
(left)
East mid
(left)
P1
P1
P4
P4
P3
P3
P2
P2
Coupler 1
Coupler 2
All Connections are to connectors as viewed from
the side of the panel with the printing
Installation Instructions
The diagram below shows the basic optical wiring for both the OSM-
6222-XY and OSM-7222-XY.
135024 Rev D
Modes of Operation
Operating Power Applied
Loop In optical port is routed to Tap and Rx Out
optical port
Tx In optical port is routed to Loop Out optical port
Note that Tap In is 30% of input optical signal
No Operating Power Applied
Loop In optical port is routed to Tap and Loop Out optical
port
Tx In and Rx Out are not used
Note that Tap In is 30% of input optical level
Power Signal Terminal Block Connections
Pin Label Function
1 Pwr+ Power + Return (Positive ground)
2 Pwr- Power – 20 to -60 Volts DC (Common/ground)
3 GND Power return and housing ground
Note that this is a positive ground system
Indicator Light
Indicator Lights When
Power Proper power is present