1.3 Megapixel IP Camera Quick Guide
The quick guide is for quick installing and connecting the IP Camera. For details, please refer to the IP Camera’s user
manual.
CameraRearPanel
DC12V/PoEModel AC24VModel
AUTO
1234
I/O
NETWORK
DC12V
LINE LINE IN
MIC IN
OUT
VIDEO
DC
IRIS
PoE
LINE
OUT
LINE IN
MIC IN
NETWORK
AUTO
IRIS
PoE
1 2 3 4 I/O
DC VIDEO
AC 24V
DC 12V
Definition Remarks
Power LED Power connection indication (green light).
Reset button Reset to factory default
DC 12V connector Power connection
ЀAC 24V: Power-1 DC 12V: Power
AC 24V: Earth GND DC 12V: Reserved
AC 24V/DC 12V connector
(AC 24V Model) ЁAC 24V: Power-2 DC 12V: GND
VIDEO/DC Video Drive/DC Drive lens selection
I/O Alarm connection
LINE OUT & LINE IN / MIC IN Two-way audio transmission
AUTO IRIS Auto iris lens connector
NETWORK (with PoE Option) RJ-45 connector
Network LEDs Network connection and activity indication
Lens Mounting
If use C-Mount lens, after removing the camera’s plastic cover, users need to mount the supplied C/CS mount adapter
to the camera. Then attach the lens onto the C/CS mount adapter.
IP Camera Installation
Please follow the instructions below to complete IP Camera installation.
Ethernet Cable Connection
Connect one end of the CAT5 Ethernet cable to the RJ-45 connector of the IP Camera, and the other end of the cable
to the network switch or PC.
NOTE: In some cases, you may need to use an Ethernet crossover cable when connecting the IP Camera
directly to the PC.
NOTE: Check the status of the link indicator and activity indicator LEDs; if the LEDs are unlit, please check
LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
Power up the Camera
NOTE: For wiring of the DC 12V/AC 24V/PoE camera with the equipped power cable, insert the wires of the
cable into the corresponding pins of the power terminal block. If using PoE, make sure Power Sourcing
Equipment (PSE) is in use in the network.
BeforeLogintotheIPCamera
A client program will be automatically installed on your PC when connecting to the IP Camera. Before logging in to the
IP Camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and
plug-ins or setting Internet’s security level to default. For further details, please refer to the IP Camera’s user manual.
ActiveX Controls and Plug-ins Settings Internet Security Level
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then Click <Internet Options>.
Step 3: Click the <Security> tab and select “Internet”,
and click <Custom level> to change ActiveX
settings.
Step 4: Set “ActiveX controls and plug-ins” items to
Step 1: Start the IE.
Step 2: Select <Tools> from the main menu of the
browser. Then Click <Internet Options>.
Step 3: Click the <Security> tab and select “Internet.”
Step 4: Down the page, press “Default Level” and click
“OK” to confirm the setting. Close the browser
window, and open a new one later for
accessing the IP Camera
IP Camera Login
The IP Camera’s default IP address is: 192.168.0.250. Therefore, to access the IP Camera for the first time, set the
PC’s IP address as: 192.168.0.XXX; for example:
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Login ID & Password
xKey in the IP Camera’s IP address in the URL bar of the Web browser window and press “Enter.”
xEnter the default user name (Admin) and password (1234) in the prompt request dialogue. Note that user name is
case sensitive.
Reset Button
Power LED
Network LEDs
Power Connector
