Luxon Video TAB2VIRWD User manual

1080P Turret &Bullet Camera
User Manual
Regulatory Informa n
FCC Informa n
FCC compliance: This equipment has been
tested and found to comply with the limits for a
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable prot n against harmful
interference when the equipment is operated in
a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the ins n manual, may
cause harmful interference to radio
communica . Opera n of this equipment in
a residen l area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
FCC s
This device complies with part 15 of the FCC
Rules. Opera on is subject to the following two
c:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired opera n.
EU Conformity Statement
upon the purchase of equivalent new equipment ,
or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (ba ery dire ve):
This product contains a ba ery that
cannot be disposed of as unsorted
municipal waste in the European
Union.
See the product documenta n for specific
ba ery informa on. The ba ery is marked with
this symbol, which may include le ering to
indicate cadmium (Cd), lead (Pb), or mercury (Hg).
2012/19/EU (WEEE dire ve):
Products marked with this symbol
cannot be disposed of as unsorted
municipal waste in th e European
Union. For proper recycling, return
this product to you r local supplier
This product and - if applicable - the
supplied accessories too are marked
with "CE" and comply therefore with
the applicable harmonized European
standards listed under the Low Voltage Direc ve
2006/95/EC, the EMC Dir ve 2004/108 /EC ,
the RoHS Dire ve 2011/65/EU.
1.2 Overview
1.2.1 Overview of Type I Camera
1.2.2 Overview of Type Camera
II
HD Video Cable
Enclosure
Zoom & Foc us
Lo ck ScrewLo ck
Moun g Base
Camera
Power Cable
Power Cable
IR LED
Lens
Main Body
Sun Shield
Moun g Base HD Video Cable
CVBS Cable
Zoom
Focus
1 Intr n
1.1 Product Features
This camera adopts new genera n sensor with
high y and advanced circuit board design
technology. It possesses the features of high
r, low dist , and low noise, etc. It is
extremely suitable for supervisory system and
image processing system.
The main features are as follows:
High performance CMOS sensor and high
re n bring high-quality image;
Low illumina ;
Support IR cut filter with auto switch;
OSD menu, parameters are configurable;
Support auto white balance, auto gain control,
electronic shu er control and internal
synchroniza ;
SMART IR mode;
Unit transmission control;
Advanced 3-axis design meets different
installa on requirements.
Please make sure that the device in the package
is in good c n and all the assembly parts
are included.
Make sure that all the related equipment is
power-off during the installa on.
Check the specifica on of the products for the
installa n environment.
Check whether the power supply is matched
with your power output to avoid damage.
Please make sure the wall is strong enough to
withstand three s the weight of the camera
and the moun .
If the wall is the cement wall, you need to insert
expansion screws before you install the camera.
If the wall is the wooden wall, you can use
self-tapping screw to secure the camera.
If the product does not n properly,
please contact your dealer or the nearest
service center. Do not disassemble the camera
for repair or maintenance by yourself.
2.1 Installa n of Type CameraI
Steps:
1.Drill the screw holes and the cable hole on the
ceiling according to the supplied drill template.
Figure 2-1 The Drill Template
2 to disassemble the camera
.
from the moun g base.
3.Fix the moun g base to the ceiling.
Figure 2-2 Release The Lock Screw
For proper recycling, return the ba ery to your
supplier or to a designated c n point. For
more informa n see: www.recyclethis.info.
2 Installa n
Before you start:
Thank you for purchasing our product. If there
are any ques ons, or requests, please do not
hesitate to contact the dealer.
This manual may contain several technical
incorrect places or prin g errors, and the
content is subject to change without .
The updates will be added to the new version of
this manual. We will readily improve or update
the products or procedures described in the
manual.
DISCLAIMER STATEMENT
Underwriters Laboratories Inc. (”UL” has not)
tested the performance or reliability of the
security or signaling aspects of this product.
UL has only tested for fire, shock or casualty
hazards as outlined in Ul’s Standard(s) for Safety,
UL60950-1. UL Cer fica on does not cover the
performance or reliability of the security or
signaling aspects of this product. UL MAKES NO
REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING
THE PERFORMANCE OR RELIABILITY OF ANY
SECURITY OR SIGNALING RELATED FUNCTIONS
OF THIS PRODUCT.
Figure 1-1 Overview of Type I Camera
Figure 1-2 Overview of Type CameraII
HD-TVI
Release the lock screw

3 Menu Operaon
Figure 3-1 Main Menu
Menu
SCENE LENS RESET
EXPOSUREWB DAY&NIGHT
BACKLIGHTNR SPECIAL ADJUST
INDOOR
OUTDOOR
INDOOR1
LOW-
LIGHT
MANUALSHUTTER
AGC
SENS-UP
BRIGHTNESS
D-WDR
DEFOG
BLC
HSBLC
ATW
AWC-SET
INDOO R
OUTDOOR
MANUAL
COLOR
B/W
EXT
2D NR
3D NR
CAM
TITLE
D-EFFECT
MOTIO N
PRIVACY
LAUGUAGE
DEFECT
VERSION
SHARPN ESS
MONIT OR
LSC
VIDEO.
OUT
EXIT
SETUP
3.1 VIDEO.OUT
PAL or NTSC is selectable .
3.2 LANGUAGE
English, Japanese, CHN1, CHN2, Korean, German,
French, Italian, Spanish, Polish, etc., are selectable.
3.3SETUP
3.3.1 SCENE
You can select indoor, outdoor, indoor 1 and low
-light as the working environments.
3.3.2 LENS
The camera is equipped with a fixed lens.
3.3.3 EXPOSURE
EXPOSURE
1. SHUTTER AUTO
2. AGC OFF
3. SENS-UP ---
4. BRIGHTNESS---|------ 40
5. DEFOG OFF
6. BACKLIGHT OFF
7. RETURN RET
Figure 3-2 Exposure
SHUTTER: AUTO,1/25, 1/50, FLK, 1/200, 1/400,
1/1k, 1/2k, 1/5k, 1/10k, 1/50k are selectable.
: You can set the AGC value from 0 to 15.AGC
: You can set the SENS-UP to OFF or AUTO.SENS-UP
: You can set the brightness valueBRIGHTNESS
from 1 to 100.
: You can set the defog funcon as ON toDEFOG
enable the funcon. Posion, size, and the defog
gradaon are configurable.
3.3.4 Backlight
Backlight Compensaon (BLC):
Set the gain of BLC as High, Middle, or Low.-GAIN:
Press the up/down/le/right buon to-AREA:
define the BLC posion and size. Select RET or
AGAIN to go back the BLC menu or re-define the
BLC area.
Restore the BLC sengs to the default.-Default:
HSBLC: Select an HSBLC area. Set the DISPLAY
status as ON. Press the up/down/le/right buon
to define the area posion and size. Set the HSBLC
LEVEL from 0 to 100. Select ALL DAY or Night for the
HSBLC mode. Set the BLACK MASK status as ON or
OFF.
HSBLC
1. SELECT AREA 1
2. DISPLAY ON
3. LEVEL ---|------ 40
4. MODEALLDAY
5. BLACK MASK ON
6. DEFAULT
7. RETURNRET
Figure 3-3 HSBLC
3.3.5 White Balance (WB)
INDOOR, OUTDOOR, MANUAL, ATW (Auto-tracking
White Balance), AWC→SET are selectable.
3.3.6 Day & Night
Color, B/W, and EXT are selectable for DAY and
NIGHT switches.
3.3.7 NR
: You can set 2D NR status as ON or OFF.2D NR
: Set the Smart NR status as ON and adjust3D NR
the 3D smart NR sensivity ranges from 0 to 100.
Set the 3D NR LEVEL ranges from 0 to 100. Set the
2D&3D NR
1. 2DNR OFF
2. 3DNR ON
3. RETURN RET
3D NR
1. SMART NR ON
2. LEVEL ------|--8 0
3. START. AGC -|--------10
4. END. AGC -|--------10
5. RETURN RET
Figure 3-5 NR
Figure 3-6 3D NR
3.3.8 SPECIAL
Edit the camera tle on this secon.Camera Title:
D-effect:
Set the freeze funcon as ON or OFF.-FREEZE:
OFF, MIRROR, V-FLIP, and ROTATE are-MIRROR:
selectable for mirror.
Define the zoom area by configuring-D-ZOOM:
the posion from PAN & TILT.
The D-Zoom area, sensivity-SMART D-ZOOM:
and me are configurable.
Set the NEG IMAGE as ON or OFF.-NEG.IMAGE:
SPECIAL
1. CAM TITLE ON
2. D-DFFECT
3. MOTION OFF
4. PRIVACY OFF
5. LANGUAGE ENG
6. DEFECT
7. VERSION130722
8. RETURN RET
Figure 3-7 Special
MOTION
1. SELECT AREA 1
2. DISPLAY ON
3. SENSITIVITY ----|---- 30
4. MOTION VIEW ON
5. DEFAULT
6. RETURN RET
Figure 3-8 Moon Detecon
Moon: Select a MOTION area. Set the DISPLAY
status as ON or OFF. Press the up/down/le/right
buon to define the posion and size of the area.
Set the SENSITIVITY from 0 to 60. Set the MOTION
VIEW status as ON or OFF.
Privacy: Select a PRIVACY area. Set the DISPLAY
status as INV, MOSAIC, COLOR or OFF. Press the
up/down/le/right buon to define the posion
and size of the area.
Defect: LIVE DPC, STATIC DPC and Black DPC are
adjustable in this secon.
: You can check the soware version of theVersion
device.
PRIVACY
1. SELECT AREA 1
2. DISPLAYMOSAIC
3. COLOR 10
4. TRANS. 1
5. DEFAULT
6. RETURNRET
ADJUST
1. SHARPNESS --------|15
2. MONITOR LCD
3. LSC OFF
4. VIDEO. OUT PAL
5. RETURNRET
3.3.9 ADJUST
: Adjust the sharpness from 0 to 15.Sharpness
: Monitor CRT, and Monitor LCD areMonitor
selectable.
: Set the LSC status as ON or OFF.LSC
3.3.10 RESET
Reset all the sengs to the default.
3.3.11 EXIT
Press OK to exit the menu.
START. AGC level as the threshold to enable AGC,
and set the END. AGC level as the threshold to
disable AGC.
Figure 3-9 Privacy MaskFigure 3-10 Adjust
Steps:
1.Drill the screw holes and the cable hole in the
ceiling according to the supplied drill template.
2.Hammer the supplied plasc expansion bolt into
the screw holes.
2.2Installaon of Type II Camera
Figure 2-5 Drill Template
Figure 2-6 Fix the Camera to the Ceiling
Figure 2-7 3-axis Adjustment
5. Adjust the surveillance angle.
1). Loosen No.1 adjusng screw to adjust the pan
posion (0 ~ 360 ).° °
2).Tighten No.1 adjusng screw .
3). Loosen No.2 adjusng screw to adjust the
lng posion(0 ~ 90 ).° °
4).Tighten No.2 adjusng screw.
5). Loosen No.3 adjusng screw to adjust the
rotaon posion 0 ~ 360 .( ° °)
6).Tighten No.3 adjusng screw .
3.Route the cables to the cable hole and connect
the corresponding cables.
4.Fix the camera to the ceiling with the supplied
screws.
A coaxial camera controller (purchase separately)
is required to select the menu and adjust the
camera parameters.
4.Route the cables to the cable hole and connect
the corresponding cables.
5.Secure the camera to the mounng base by
ghtening the lock screw.
6.Adjust the camera according to the figure below
to get an opmum angle.
Figure 2-3 3-axis Adjustment
7.Use the screwdriver to adjust the ZOOM screw
and the FOCUS screw unl you get the opmum
image.
Figure 2-4 Zoom and Focus Adjustment
Both wall mounng and ceiling mounng are
suitable for type bullet camera. Ceiling mounng
will be taken as an example in the secon. And you
can take steps of ceiling mounng as a reference
if wall mounng is adopted.
0~360
0~360
09~0
1
2
3