LuXout Shades Multi-Channel Controller User manual

Multi-Channel Option
Level Control
Touch Sensitive
433 MHz
The LuXout Shades Multi-Channel Controller features a contemporary design with touch sensivite controls. Each battery
and plug-in shade from LuXout Shades will come preprogrammed from the factory. The pre-programming assures the
remote is paired with the shade, the upper and lower operation limits are set, the remote is locked and the unnecessary
channels are hidden for ease of use. (15 available)
Features:
• Up to fifteen channel capacity.
• Touch sensitive buttons.
• Slim Magnetic wall mount.
• LCD display.
• Hide unused channel function.
• Levelling control.
• Individual/group contol.
About The Controller
Package Contents
• Remote
• Magnetic holder &
fixing screws
• Instruction Manual
• 3V - CR2450 Battery
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
OVERVIEW
LUXOUT
VIDEOS

Multi-Channel Overview
BACK
Battery
Compartment
(Shown with
cover removed)
FRONT
Multi-
Channel
SLIDE CONTROL
CHANNEL
DOWN
STOP
UP
LCD Screen
TECHNICAL SPECIFICATIONS
Voltage 3V (CR2450)
Frequency 433.92 MHz
Transmitting Power 10 milliwatt
Ambient Operating
Temperature
-10°C - 50°C
Transmission Distance Up to 600 feet
(open spaces)
Battery CR2450
P2P2
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
OVERVIEW LUXOUT
VIDEOS

Install Wall Mount Holder
Replace cover by pressing snap
latches into place
Use supplied fasteners to attach base to desired
surface as shown in figure
Assure screwdriver slot is facing up or
the controller will not be held in place
securely
Remove cover from base by prying with
flat head screwdriver
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
OVERVIEW

Install or Replace Controller Battery
Install battery with
positive (+) side facing up
Replace cover by
reversing step 1
Remove cover from
controller: with 2 fingers
placed in upper area of
cover, press gently in and
down to disengage cover
and slide down to remove
Unlock/Lock Controller - Limit Setting
If limits need adjusting, follow the instructions
below to unlock the controller for limit setting:
• Unlock the limit setting tool by pressing the right
P2 button on the back of the controller (remove
cover to expose the button)
• Press and hold the button until the LED display
shows a flashing “U”, then release.
• You will be required to set the controller back in to
“limit locking mode” once final adjustments have
been made. Simply repeat the above step until a
flashing “L” shows on the display (“U” for un-
locked, “L” for locked).
U
P2P2
Right
P2
‘U’
signifies
unlocked
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
OVERVIEW

Motor head
programming button
Motor head
programming button
It is necessary to “Wake” the motor before operation and setup. (Rechargeable
battery motors only)
Each battery & plug-in motor comes preprogramed from LuXout Shades. Upon leaving the factory
the motor is placed into “Sleep Mode” to avoid accidental operation during shipping.
To “Wake” the motor and exit Sleep Mode, assure the motor is installed and secured in the
mounting hardware.
After the motor is installed in the brackets, press and hold the programming button on the motor head
until the motor jogs up and down once. It is now no longer in “Sleep Mode”and ready for further setup.
* Warning, if you press and release the programming button quickly, the motor will lower to
its lower limit. Be mindful of this during the install process.
SLEEP
If required, to place the motor back into “Sleep Mode” press and hold the programming button
for a period of 6 seconds. Release the button when the motor has jogged up and down twice.
The motor will beep twice to signify “Sleep Mode” has been activated.
Motor head
programming button
Motor head
programming button
Motor Response
HOLD
6
SEC.
JOG
x1 BEEP
x2
JOG
x1
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
SLEEP MODE LUXOUT
VIDEOS

Each battery & plug-in motor will come preprogrammed from LuXout Shades. The preprogram-
ming assures the remote is paired with the motor, the upper and lower operation limits are set,
the remote is locked and the unnecessary channels are hidden for ease of use (15 available).
Follow the below steps to select the remote channel you want to pair with the motor(s) if required
at a later date.
Pairing/Removing Motor From A Specific Channel
A). Press any button
to wake controller.
HOLD CH (1 second)
LCD screen will flash
to confirm.
B). Within 4 seconds
Press UP or DOWN
to select desired
channel.
C). Press STOP to
confirm selection
OR controller will
auto confirm
after 4 seconds.
CH
CH CH CH
Motor head
programming button
Motor head
programming button
Press and HOLD
programming button
on motor head for
2 seconds.
Select Channel
Within 4 sec of activating
pairing mode, Press
& Hold STOP.
If you do not pair the controller in time the motor pairing sequence will time out, repeat
the above steps assuring to press and hold the STOP button within 4 seconds of the motor jog.
Motor Response
LONG
BEEP
JOG
x1
x1
HOLD
2
SEC.
Motor Response
BEEP
JOG
x3
x2
HOLD
2
SEC.
CH
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
REMOTE & MOTOR PAIRING

To reverse the motor direction at any time, use the motor operation method shown below.
Motor head
programming button
Hold Programming Button (10 seconds)
Motor head
programming button
HOLD
10
SEC.
JOG
x1 JOG
x1 BEEP
x3
JOG
x1
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
REVERSE MOTOR DIRECTION LUXOUT
VIDEOS

Motor Response
A). Press any button
to wake controller.
HOLD CH (1 second)
LCD screen will flash
to confirm.
B). Within 4 seconds
Press UP or DOWN
to desired channel.
C). Press STOP to
confirm selection
OR controller will
auto confirm
after 4 seconds.
CH
CH CH CH
1). Select Channel On Existing Controller To Be Copied
2). Add/Remove Controller Using An Existing Controller
Select channel on existing controller to be copied. Select channel on new controller where existing channel
will be copied.
P2P2 P2P2
A). On existing
controller, press left P2
for 1 second.
B). On existing
controller, press left P2
for another 1 second.
C). On new
controller, press left P2
for 1 second.
Motor Response Motor Response
P2P2
BEEP
JOG
x1
x1
HOLD
1
SEC.
BEEP
JOG
x1
x1
HOLD
1
SEC.
BEEP
JOG
x3
x2
HOLD
1
SEC.
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
MIRRORING CONTROLLERS LUXOUT
VIDEOS

Adjusting Upper Limits
If limits need adjusting, follow the instructions
below to unlock the controller for limit setting:
• Unlock the limit setting tool by pressing the right
P2 button on the back of the controller (remove
cover to expose the button)
• Press and hold the button until the LED display
shows a flashing “U”, then release.
• You will be required to set the controller back in to
“limit locking mode” once final adjustments have
been made. Simply repeat the above step until a
flashing “L” shows on the display (“U” for un-
locked, “L” for locked).
U
P2P2
Motor Response
Delete Top Limit
Press UP & STOP
5 seconds
Move the shade
to the new desired
position to be set
as limit.
IMPORTANT!! Stop
the shade before traveling
past the desired
lower limit.
Set Top Limit
Press UP & STOP
5 seconds
Motor Response
BEEP
JOG
x1
x1
HOLD
5
SEC.
BEEP
JOG
x3
x2
HOLD
5
SEC.
‘U’
signifies
unlocked
Right
P2
CH CH
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
ADJUSTING LIMITS LUXOUT
VIDEOS

Adjusting Lower Limits
!!WARNING!! - Move shade in short increments by pressing the UP/DOWN button in 1 second intervals (press-
ing the UP/DOWN button for more than 3 seconds may send the shade past desired upper/lower limit and may
result in damage to the product). Once you have reached the desired upper/lower limit, you can adjust the limit with
either the UP and DOWN buttons. (remember to adjust in short increments!)
Motor Response
CH
Delete Lower Limit
Press DOWN & STOP
5 seconds
Move the shade
to the new desired
position to be set
as limit.
IMPORTANT!! Stop
the shade before traveling
past the desired
lower limit. CH
Set Lower Limit
Press DOWN & STOP
5 seconds
Motor Response
BEEP
JOG
x3
x2
HOLD
5
SEC.
BEEP
JOG
x1
x1
HOLD
5
SEC.
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
ADJUSTING LIMITS LUXOUT
VIDEOS

Hide/Unhide Controller Channels
A). Press & Hold
STOP + CH
Controller Response
LCD screen flashes
“15” which defaults
controller control to 15
visible channels
B). Release only STOP
Keep CH pressed for
the entire procedure.
C). Press UP or DOWN
to select number of
active channels.
D). Press STOP, then
release CH to
confirm.
CH CH
Release
Hold CH CH
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
HIDE/UNHIDE CONTROLLER CHANNELS LUXOUT
VIDEOS
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204

Setting Favorite
Follow the below steps to set a favorite position. The favorite position is used to set a custom stopping
point between the upper and lower limits. (1 favorite position per shade motor).
To set a favorite position for a shade motor, move to the desired position and press the STOP button to
pause the drive operation.
Motor Response
B). Press left P2.
P2P2
C). Press STOP.
Motor Response
D). Press STOP
again.
Motor Response
A). Press UP or
DOWN to move
shade to desired
favorite position.
* Press STOP (3 seconds) to move shade to the Favorite Position from any location.
* Repeat Steps A - D for any additional motors.
CH CH
Delete Favorite
Follow the below steps to set a favorite position. The favorite position is used to set a custom stopping
point between the upper and lower limits. (1 favorite position per shade motor).
Motor Response
B). Press left P2.
P2P2
C). Press STOP.
Motor Response
D). Press STOP
again.
Motor Response
A). Press STOP
(3 seconds) to
send the shade
to the stored
favorite position.
CH CH
x1 x1
HOLD
1
SEC.
BEEP
JOG
x3
x2
HOLD
1
SEC.
BEEP
JOG
x1
x1
HOLD
1
SEC.
BEEP
JOG
x1
x1
HOLD
1
SEC.
BEEP
JOG
x1
x1
HOLD
1
SEC.
BEEP
JOG
x1
x1
HOLD
1
SEC.
LONG
BEEP
JOG
x1
x1
HOLD
1
SEC.
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
FAVORITE POSITIONS

1). Select Channel To Be Paired As A Group
Each battery & plug-in motor will come preprogramed from LuXout Shades. If multiple motors are paired
to the same 15 channel remote, the 0 channel is the default channel to control all motors at once. Follow
the steps below to group motors on a specific channel for simultaneous control.
To custom define a channel to control multiple motors, pairing in groups can be executed. This will allow
you to operate a series of motors in unison without needing to change channels. Each motor to be grouped
must be paired with the remote on its own channel prior to grouping.
A). Press any button
to wake controller.
HOLD CH (1 second)
LCD screen will flash
to confirm.
B). Within 4 seconds
Press UP or DOWN
to desired channel.
C). Press STOP to
confirm selection
OR controller will
auto confirm
after 4 seconds.
CH
CH CH CH
2). Pairing Controller to Motor
Repeat for all motors to be added or removed from your desired group channel.
Motor head
programming
button
Motor head
programming button
Motor Response
Press and HOLD
programming button
on motor head for
2 seconds.
A). Activate Pairing Mode on Motor
LONG
BEEP
JOG
x1
x1
HOLD
2
SEC.
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
GROUP CONTROL

B). Pairing Controller
Within 4 sec of activating
pairing mode, Press
& HOLD STOP.
If you do not pair the controller in time the motor pairing sequence will time out,
repeat the above steps assuring to press and HOLD the STOP button within
4 seconds of the motor jog.
CH
Motor Response
3). Adjusting limits of an individual shade paired on a group channel
To adjust the limits of a shade that is currently grouped on a channel with other shades, it is necessary to
place all shades, with the exception of the shade to be adjusted, to sleep.
Once all other shades have been put to sleep, unlock controller by pressing and HOLDING the upper left
P2 button under the battery cover until “U” is displayed on the LCD screen. Adjust the shade limits as
outlined below:
Motor head
programming button
Motor head
programming button
BEEP
Motor Response
BEEP
JOG
x3
x2
HOLD
2
SEC.
JOG
x1 BEEP
JOG
x2
x1
HOLD
6
SEC.
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
GROUP CONTROL LUXOUT
VIDEOS

Adjusting Upper Limit Adjusting Lower Limit
!!WARNING!! - Move shade in short increments by pressing the UP/DOWN button in 1 second
intervals (pressing the UP/DOWN button for more than 3 seconds may send the shade past
desired upper/lower limit and may result in damage to the product). Once you have reached the
desired upper/lower limit, you can adjust the limit with either the UP and DOWN buttons.
(remember to adjust in short increments!)
Motor Response
CH
Delete Top Limit
Press UP & STOP
5 seconds
Move the shade
to the new desired
position to be set
as limit.
IMPORTANT!! Stop
the shade before traveling
past the desired
upper limit.
CH
Set Top Limit
Press UP & STOP
5 seconds
Motor Response
CH
Delete Lower Limit
Press DOWN &
STOP. 5 seconds
CH
Set Lower Limit
Press DOWN & STOP
5 seconds
Move the shade
to the new desired
position to be set
as limit.
IMPORTANT!! Stop
the shade before traveling
past the desired
lower limit.
Motor Response Motor Response
Once the limits have been adjusted as desired, return the controller to “L” mode by
pressing and holding the upper left P2 button under the battery cover. The other grouped
motors can now be taken out of sleep mode by holding the programming button for 6 seconds.
BEEP
JOG
x1
x1
HOLD
5
SEC.
BEEP
JOG
x3
x2
HOLD
5
SEC.
BEEP
JOG
x1
x1
HOLD
5
SEC.
BEEP
JOG
x3
x2
HOLD
5
SEC.
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
GROUP CONTROL

Motor head
programming button
Motor head
programming button
Approx.
Motor Response
The motor will jog 4 times before the reset is complete. The P1 button must be held the entire time. 4
beeps confirm the factory reset is complete.
Refer to the Initial Setup Programming section to program a shade after a factory reset.
Each battery & plug-in motor will come preprogramed from LuXout Shades. The preprogramming assures
the remote is paired with the motor, the upper and lower operation limits are set, the remote is locked and
the unnecessary channels are hidden for ease of use (15 available).
Follow the below steps to reset the motor to factory settings and delete all limits.
To reset the shade motor to factory settings with no stored limits locate the P1 button on the motor head.
HOLD the programming button for 14 seconds (4 motor jogs). External battery motors will jog 3 times for
a full factory reset.
Motor Response
BEEP
JOG
JOGJOGJOG
BEEP
JOG
x2
x1
HOLD
6
SEC.
JOG
x1
HOLD
14
SEC.
JOG
x1 JOG x1 JOG x1
JOG
x1
BEEP
x4
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
RESET TO FACTORY SETTINGS

Follow the below steps to adjust the motor speed (ONLY APPLICABLE TO DC MOTORS).
To adjust the motor speed a remote must be paired.
To enter speed adjustment mode remove the rear battery cover of the remote. Press and HOLD the
left P2 button for 2 seconds. the motor will perform one up and down jog and beep once.
P2P2
Motor Response
To Increase Speed
To Decrease Speed
CH CH
CH CH
IMPORTANT
If motor does not react
to speed adjustment, the
maximum or minimum
speed has already been
reached.
IMPORTANT
If motor does not react
to speed adjustment, the
maximum or minimum
speed has already been
reached.
Motor Response
Press U P.
Motor Response
Press U P.
Motor Response
Press DOWN.
Repeat
Motor Response
Press DOWN.
BEEP
JOG
x1
x1
BEEP
JOG
x1
x1
BEEP
JOG
x1
x2
BEEP
JOG
x1
x1
BEEP
JOG
x1
x2
Repeat
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
ADJUSTING MOTOR SPEED LUXOUT
VIDEOS

Issue Cause Solution
Battery is insertedincorrectly
Radio interference
Cannot set limits on
a single Motor (multi-
ple motors respond)
Motor is not
responding
/Shielding
Controller battery is
discharged
Receiver distance is
too far from controller
Power failure
Incorrect wiring
Using ‘group’ channels
to adjust motor limits
Replace battery
Check battery polarity
Ensure controller is positioned away from metal
objects and that aerial on motor or receiver is kept
straight and away from metal
Move controller to a closer position
Check power supply to motor is connected & active
Check wiring is connected correctly (refer to motor
installation instructions)
Always reserve an individual channel for
programming functions.
System Best Practice - Provide an extra
Multi-Channel Controller in multi motor projects
that provide individual control for each motor
for programming purposes.
SPECIFICATION SUBMITTAL
JOB NAME
JOB NUMBER
MODEL NUMBERS
LUXOUT SHADES
SIMPL Y BEAUTIFUL
Effective: June 1, 2019
LUXOUT SHADES
SIMPLY BEAUTIFUL
1221 Admiral Street | Richmond, VA | 800-817-1204
INSTRUCTIONS
MULTI-CHANNEL CONTROLLER
TROUBLESHOOTING LUXOUT
VIDEOS