Luxul Pro-WAV 200 PW200-24-FC2 User manual

WG103 AP Included
FCC
CERTIFIED
Congratulations on your purchase of the Luxul Pro-WAV™ Range Extender
System! You are just minutes away from enjoying the benefits of a farther
reaching, clearer wireless signal in your home or office.
LuxuL WIRELEss PRoDuCTs CovERED by ThIs GuIDE
PW200-24-FC2 - Pro-WAV 1W 2.4GHz indoor Wi-Fi Range Extender System
Pro-WAV™ 200
Wi-Fi rAnge extender SyStem
QUiCK inStAll gUide

QUiCK inStAll gUide
PRo-WAv™ 100 WI-FI RAnGE ExTEnDER sysTEm
MODEL NUMBER: PW200-24-FC2
© 2010 by Luxul Wireless Inc. All rights reserved
No part of this publication may be modified or adapted in any way, for any purposes
without permission in writing from Luxul Wireless, Inc. (Luxul). The material in this manual is
subject to change without notice. Luxul reserves the right to make changes to any product
to improve reliability, function, or design. No license is granted, either expressly or by impli-
cation or otherwise under any Luxul Wireless, Inc., intellectual property rights. An implied
license only exists for equipment, circuits and subsystems contained in Luxul products.
This product is covered by one or more U.S. and foreign patents.
Patents: 7,783,270, 7,379,717, 6,606,075, 6,373,448, other patents pending
SHOCK-WAV™ WI-FI SIGNAL BOOSTER NETGEAR®
moDEL numbER: PW-FC2 moDEL numbER: WG103
FCC ID: W59PWFC2 FCC ID: PY308400097
IC: 8584A-PWFC2 IC: 4054A-08400097
Luxul Wireless, Inc. NETGEAR, Inc.
357 South 670 West, Suite 160 350 East Plumeria Drive
Lindon, UT 84042 San Jose, California 95134-1911
www.luxulwireless.com www.netgear.com
PRoFEssIonAL InsTALLATIon ConsIDERATIons
The Luxul Wireless Pro-WAV Wi-Fi Range Extender System is required to be professionally
installed. The following components are approved for use in the system.
• Luxul Wireless Shock-WAV PW-FC2 Wi-Fi Signal Booster
• Luxul Wireless X-WAV™ XW-24-FP7 Flat Panel Antenna
• Netgear ProSafe WG103 Access Point
• Netgear Omni antenna included with WG103 access point
The output power of the amplifier is set and tested during manufacturing. There are no user
modifiable parameters in the amplifier. The Luxul Shock-WAV Wi-Fi Signal Booster system
incorporates a Digital AGC (D-AGC) that ensures a consistent and approved output power.

QUiCK inStAll gUide
ThE PRo-WAv RAnGE ExTEnDER InCLuDEs ThE FoLLoWInG:
• Metal Enclosure with space for mounting
the AP (Access Point) internally
• Shock-WAV™ 802.11b/g Signal Booster
• Two X-WAV™ CP (Circularly Polarized)
Antennas
• Three Ethernet cables
• Three Coax cables
• POE (Power-Over-Ethernet) Injector
• 48VDC Universal Input Power Supply
• Mounting Hardware
• Ethernet Pass Through
• Signal Splitter
• Barrel Connector
• Velcro
• Quick Install Guide
• Netgear ProSafe Access Point.
– Included with the Netgear is: a
Detachable Antenna, Ethernet Cable,
Power Supply, Installation Guide,
Warranty/Support Information Card
and Resource CD.
ADDITIonAL ITEm REquIRED
External Ethernet cable from your data/network source (Max. length 329’ or 100 meters).
oPTIonAL EquIPmEnT
• HDW-PWM - Optional drop ceiling mounting arms for Pro-WAV systems
ConFIGuRE youR AP
See the guide included with your AP and configure the AP before you connect the Luxul
Range Extender System. Once the AP is configured, disconnect all power and connect the
Luxul Range Extender System.
CAUTION: Disconnect all power before connecting or disconnecting any cables
or coax to or from this device. Failure to do so will void your warranty.

QUiCK inStAll gUide
AssEmbLE ThE RAnGE ExTEnDER sysTEm
1. Connect the two X-WAV antennas to the
antenna mount. Position the antennas so the
N connectors are above the antenna mount
(Figure 1).
2. Attach the antenna mount to the top of the
enclosure using the washers and nuts
provided.
3. If mounting the Pro-WAV 200 high in your Wi-Fi
coverage area the antenna mount may be bent
slightly downward to focus signal into the desired
coverage area
4. Mount the AP to the enclosure using the included Velcro mounting strips.
WIRInG ThE RAnGE ExTEnDER sysTEm
1. Remove the stock antenna from your AP. Set
aside the stock antenna, you will not need it for
this installation.
2. Find the N Male to RP-SMA coax connected to
the side of the Shock-WAV Wi-Fi Signal booster
labeled “AP” (Figure 3) and connect it to the
antenna port of your AP.
3. Find the N Male to N Male coax cables
connected to the splitter that is attached to the
Shock-WAV Wi-Fi Signal Booster on the side labeled “Antenna” (Figure 3).
4. Feed the coax cables through the round pass through hole in the top of
the enclosure, (Figure 2) and connect them to the X-WAV antennas.
FIGURE 1
FIGURE 2
WAP
POE
OUT
POE
IN
ANTENNA
48V
DC IN
FIGURE 3

QUiCK inStAll gUide
PoWERInG oPTIons
For maximum flexibility you may power the Pro-WAV
Range Extender System by Direct Power or POE
using the Luxul Wireless POE Injector or a POE
injector that supports legacy mode. The Luxul
Wireless Signal Booster does not support 802.3af
POE power. (Check POE’s documentation).
1. Decide where your Ethernet source will enter the
Pro-WAV enclosure, left, right or bottom, and place
the Ethernet pass through in that location.
2. DO NOT connect your external Ethernet source
or power source at this time.
Direct Power: (Figure 4)
NOTE: If powering the Shock-WAV
Signal Booster directly the
“POE OUT” port is disabled.
1. Connect the Ethernet cable from the Ethernet pass
through to the “10/100M” port of your Netgear
AP, (See AP’s documentation).
2. Attach the Luxul power supply (48VDC) to the
“48V DC IN” port of the Signal Booster.
3. Connect Netgear power supply to the AP’s power
port (See AP’s documentation).
4. Plug the power supplies into your power source.
Optional POE (Power Over Ethernet) (Figure 5)
1. Connect the Ethernet cable from the Ethernet pass
through to the “48V POE IN” port of the Wi-Fi Signal Booster.
2. Connect the next Ethernet cable from the “POE OUT” of the Wi-Fi Signal Booster
to the “10/100M” port of your Netgear AP, (See AP’s documentation).
3. Be sure all cables are connected securely and power up your POE injector.
4. You may now power your POE injector.
FIGURE 5
FIGURE 4

QUiCK inStAll gUide
Optional POE with the POE-1Port Injector (Figure 4)
Install the optional POE injector where you have
access to your data/network source Ethernet cable
and power sources.
NOTE: The POE-1Port is a non 802.3af/ at compliant injector
DEPLoymEnT
The Pro-WAV 200 System features high gain directional antennas. Remember to consider
the direction of the signal when positioning the enclosure. The signal extends out in both
directions from the antennas mounted on the sides of the enclosure. If mounting the
Pro-WAV 200 high in your Wi-Fi coverage area the antenna mount may be bent slightly
downward to focus coverage. Use Figure 6 and 7 below to position your Pro-WAV 200
system for maximum Wi-Fi coverage.
Placement Within Your Coverage Area
Luxul Wireless products, particularly those implementing our patented booster
products, are often capable of emitting enough signal strength to cover an entire
home regardless of orientation. However, for best results, the deployment suggestions,
figure 5, are recommended.
FIGURE 6
FIGURE 6
Data
Source
Power
Source
Data
In
Power
In Data/Pwr
Out
POE
Injector

QUiCK inStAll gUide
Large or Unusually Shaped Coverage Areas
If installing the Wi-Fi Range Extender System in a large or unusually shaped coverage area
Figure 7 demonstrates how two antennas can more effectively be aimed into your desired
coverage area..
FIGURE 7

Results may vary depending on building layout, type of construction and other environmental factors
including Wi-Fi traffic, Microwave Ovens, Cordless Phones etc.
FCC NOTICE: The use of all radio equipment is subject to regulations in each country. To comply with FCC part
15 rules in the United States, radio equipment must only be used in systems that have been FCC certified. It is the
responsibility of the user/professional installer/operator to ensure that only approved equipment/systems are
deployed. To ensure FCC part 15 compliance, Luxul amplifier products should only be installed in certified systems
by licensed professionals.
FCC Certification Support for OEMs: Luxul Wireless offers FCC certification assistance and engineering support
for qualified OEM’s interested in certifying complete amplified WLAN systems. Please contact us for details.
LUXUL WIRELESS | 357 South 670 West, Lindon, UT, 84042
p: 801-822-5450 f: 801-822-5460 | www.luxulwireless.com
LUX-QIG-090320101236-PW200FC2
© 2010 Luxul Corp. All rights reserved.
TRoubLEshooTInG
Weak or non-existent coverage.
• Make sure the cables are properly connected and that there is power to the Shock-WAV
Wi-Fi Signal Booster and your WAP (Wireless Access Point).
• If the Signal Booster is powered the Power and TX/RX indicators will be solid green. If
data is passing through the signal booster the TX/RX indicator will be Green with flashing
Red. If there is no indication of data pass through remove the Luxul unit and test with
the WAPs stock antennas to make sure the WAP’s radio is transmitting. If the WAP is not
transmitting check your WAP’s documentation for possible causes.
• Sometimes, WAP’s with multiple antennas have primary and secondary antenna ports.
Be sure to connect the signal booster to the primary antenna port of the WAP as many
secondary ports are receive only, or do not transmit at the same power level as the
primary antenna port. If your WAP has more than one antenna port, try connecting
to a different port and/or, if available, change the administration settings disable the
secondary antenna port. (See your WAP’s documentation).
• Ensure the X-WAV antenna is properly positioned. Directional antennas should face the
direction of the area to be covered. Omni antennas should be centered in the desired
coverage area. Antennas should have minimum of 2 feet (.6 meters) of clearance with
no obstructions.
• The Luxul Wireless Circular Polarized signal is superior for penetrating wood, concrete,
and stucco, but all wireless signals can be disrupted by certain obstructions, including
large metal objects, or strong magnetic fields. Try orienting the antenna where line-of-
sight access to the desired coverage area is available.
After checking the above items, if your Luxul Wireless product still does not seem to be
functioning properly, please contact Technical Support at: [email protected]om
For warranty information please go to: www.luxulwireless.com/warranty/