Lydsto R3 User manual
Lydsto Sweeping and mopping robot R�
Instruction Manual
Tips
TABLE OF CONTENTS
Safey information
Packing list
Technology parameter
Product presentation
Fast installation
Method of use
APP connection
Instructions
Maintenance
Troubleshooting
1
2
3
4
6
7
8
9
12
18
Use limits
Battery and charging
·It is forbidden to burn the product even if it is seriously damaged, and the battery in the product may
explode due to burning. Do not discard the battery at will.
·Do not use any third-party batteries, charging equipment.
·Do not disassemble, repair or refit the battery and charging pile without permission.
·Do not place the charging pile close to the heat source (such as radiator).
·Do not wipe the electrode contact piece of the charging pile with wet hands or wet cloth.
·If the power cord is damaged, it must be replaced with a special cord or a special component purchased
from its manufacturer or maintenance department.
·If the product needs to be transported, please ensure that the host is turned off, and it is recommended to
use the original packaging box.
·If it is not used for a long time, please charge it at least every 3 months to avoid damage to the battery due to
over discharge.
·When taking out the battery, first cut off the power, and then use the correct tools. First take out the screws
of the battery cover, then open the bottom cover of the product, remove the battery connection terminal, and
take out the battery from the battery.
·Plastic bags are dangerous. Please keep them away from infants and young children to avoid suffocation.
·This product is only used for floor cleaning in normal temperature home and indoor environment. It should
not be used outdoors (such as open balcony) and in commercial and industrial environment.
·Please do not use it in the hanging environment without protective fence.
·Please hang the cable on the ground at home before use to avoid dragging the cable when the host is
running.
·Please put away the fragile articles placed on the ground at home before use.
·Do not use this product on uneven non floor.
·Do not let children and people with intellectual deficiency use the product, and do not let children use the
product as a toy. Please prevent pets in your home from interfering with the robot's work.
·Do not use it to clean burning materials (such as cigarette butts, mosquito repellent incense, etc.).
·Do not use it to clean sharp or hard objects (such as decoration waste, glass, nails, etc.).
·Do not use in the toilet, do not clean the machine with water, and use a rag to wipe the surface of the
machine.
·Please use the product according to the instructions. The user shall bear the loss and injury caused by
improper use, manual disassembly and intentional damage.
Safety information
-1-
Packing list
-2-
* The illustrations of products, accessories and user interface in the manual are schematic diagrams for
reference only. Due to product updates and upgrades, the actual product may be slightly different from
the schematic diagram. Please refer to the actual product.
Main unit1
Cleaning brush1Mop1
Mop support×1
(Including 1 installed mop,
plus 1 as a gift, 2 in total.)
((The dust bags are placed in
the dust bag bin of the dust
collector, one of which has
been installed.))
(The knife is placed in the
slot on the dust box)
HEPA2
Side brush4Manual1
Dust collector1
Dust bag2
Cleaning robot
Product name
Product model
Product size
Charging input
Working voltage
Rated power
Battery type
Battery capacity
Robot Vaccum
YM-R3-B03、YM-R3-W03
350*350*73 mm
19V 1A
14.4V
35W
Lithium battery
2600mAh / 5200mAh(Choosable)
Technical specification
-3-
Dust collector
Input
Output
Rated power
Product size
19V 1A
19V 1A
900W
195*250*325mm
Recharg/pauseSwitch on/off/sweep
*Long press, 3 seconds on/off.
*Short press to start global cleaning.
Bumper
Charge sheet
Dust box botton
Charging sheet
Left side brush Right side brush
Cliff sensor
Cliff sensor
Cliff sensor
Side wheel
Power button
Recharging
botton
Reset button
Laser sensor
*Press to start automatic recharge;
*Long press for 3 seconds to start local cleaning;
*Short arbitrary keys pause during recharge.
1. Main unit
Product presentation
-4-
Dust box button
Universal wheel
Roller brush
Side wheel
Roller brush cover
2 in 1 Water tank
Mop support
Indicator light reminder
Robot status
Power on
Stand by
Charging
Pause
Cleaning
Recharging
Exception
Power off
WIFI reset
WIFI connected
WIFI connecting
WIFI connection fail
Blue light on
Always blue light
Blue light flash
Blue light slow flash
Always blue light
Extinguish
Red light fast flash
Blue light fast flash
Blue light on
Always blue light
Blue light flash
Red light flash
Extinguish
Extinguish
Extinguish
Extinguish
Extinguish
Always Orange light
Extinguish
Extinguish
Extinguish
Extinguish
Extinguish
Extinguish
Recharge lightPower light
2. Dust collector
Product presentation
-5-
Dust collector cover
Vacuuming mouth
Display
Charge sheet
Warning dust bag is full,
please replace the dust bag.
Indicates the battery status
of the host.
Prompt deodorant working
status, light on as working
The device is collecting the
garbage in the dust box.
1. Remove the protective foam horizontally from both sides of the machine. Take out the left and right side
brushes and install them on the machine in the direction indicated. Handle with care during operation.
2. Place the dust collector against the wall and ensure that there is no obstruction within 0.5 meters on both
sides and 1.5 meters in front of it. Wrap the excess wire around the winding board and plug it in.
3. Before use, please put the main machine on the dust collector to charge, and then use after full.
Fast installation
-6-
Close to the wall
0.5m 0.5m
1.5m
1. Before use, collect all kinds of cables and fragile items (such as vases and wine
bottles) on the floor of the room. The stairs in the home again,elevator, kitchen and
bathroom door set up good protective facilities, so as not to damage. Please be
careful not to use robots to clean up standing water.
Method of use
-7-
APP connection
-8-
1. Sweep/pause
After the machine is successfully switched on, short press the “ ”button on
the main machine, or use mobile phone APP to start the sweeping or pause.
2. Recharging
When in use, if the power of the device is low, it will automatically return to
charging. In the pause state, short press the “ ” button to start the recharg-
ing, or control the recharging in the mobile APP.
3. Operating Mode
Swept area
Area to be swept
3.1 Automatic sweeping
After the machine is started, the equipment first selects the 4.5*4.5m area
and performs bow cleaning, and after cleaning the 4.5*4.5 area, it will move
to the next partition, so as to achieve an orderly and efficient cleaning of
the whole house. After cleaning, it will Automatically return to the charging
base for charging. The default automatic cleaning mode when the Robot is
powered on.
Instructions
-9-
4.5M
4.5M
Swept area
Area to be swept
3.2 Fixed-point sweeping
Using the “ ”function on the mobile phone APP, the Robot will take itself as
the center to sweep the area with a diameter of 1.5*1.5m for bow cleaning,
and the Robot will automatically return to the starting position after cleaning
and stop working.
3.3 Local sweeping
With the current position of the robot as the center point, the area of
1.6*1.6m is the area for local cleaning. After the sweeping, the Robot will
stop in place and wait for the next command.
Instructions
-10-
1.5M
1.5M
1.6M
1.6M
3.4 Scheduled sweeping
The appointed sweeping time can be set by the mobile phone APP, the
Robot will automatically start sweeping at the specified time, and return
to the charging base for charging after the sweeping is completed.
(7X24-hour scheduling supported.)
3.5 Silent mode
When the silent mode is started, the Robot will not play voice, and the
silent mode can be opened or closed on the mobile phone APP.
4. Suction adjustment
Use the mobile APP to select strong, normal and quiet modes, the default is
normal mode.
5. Water volume adjustment
High-level, middle-level and low-level modes can be selected by using the
mobile phone APP (the default is middle-level mode).
Instructions
-11-
1. Rolling brush (It is recommended to clean it once a week)
2. Side brush (It is recommended to clean it once a week)
*The roller brush is a consumable item, and it is recommended to replace it every 3 months to ensure the
cleaning effect. Please buy it on the official website.
Flip the machine, press the snap on the rolling brush cover and remove the rolling brush cover, and then
remove the rolling brush. Use the matched cleaning brush to clean the dust from the main brush and the
rolling brush chamber, and then clean the entangled matters on the rolling brush. After cleaning, install the
rolling brush back in the opposite direction.
Maintenance
-12-
2.1 Flip the machine and vertically pull out the side
brush.
*Match left-side brush (L) and right-side brush (R) with the letters L and R on the bottom case, respectively and
press down to install it.
*The roller brush is a consumable item, and it is recommended to replace it every 3 months to ensure the
cleaning effect.
*Please buy it on the official website.
2.2 Reinstall it after cleaning up the entanglement
and dirt.
3. Maintenance of water tank/dust box/filter screen (it is recommended to clean and maintain
after each use)
* Please do not add washing liquid, detergent, etc. Do not clean or soak the tank.
Maintenance
-13-
3.1 Press dust box on the button, and then back out
it.
3.3 Remove the filter gauze/ HEPA and sponge, and clean the filter gauze with water. Use a cleaning tool to
remove debris from the HEPA. HEPA can't be washed, sponges can be washed. Then clean dust box, waiting
for the sponge and filter gauze were to dry up again after use.
3.4 Make sure there is water in the water tank before using the mop function. Press the button on the tank dust
box and then pull back the tank dust box. Open the lid of the water tank and add the appropriate amount of
water and fasten the lid.
*HEPA filter and sponge are worn goods, it is recommended to replace one set every 3 months, please buy it
on the official channel.
3.2 Press the switch of the dust box of the water
tank, open the dust box and pour the garbage into
the trash can.
Early effective
screen HEPA screen Sponge cover
4. Mopping module maintenance (cleaning and maintenance after each use is recommended)
5. Robot signal area maintenance (recommended monthly cleaning)
Maintenance
-14-
Gray areas
represent paste
area
dirty or
disposable
mops.
mopping bracket
button
4.1 Press the mopping bracket button with double
pointing inside to remove the mopping bracket from
the equipment.
4.3 Clean mop or disposable mop clean and dry,
to install or remove a new mop, disposable mop
mop stents. Finally, install it back to the robot in the
opposite direction of the removed bracket.
5.1 Clean the front anti-collision sensor with a soft, dry cloth.
Attentions:
*Do not use the mopping function on the carpet.
*In order to get a better mop effect, it is recommend-
ed to clean the mop in time.
*Replace the mop according to the actual use
situation, so as not to affect the use effect.
*Mops are wear and tear goods, please purchase
from the official channel.
4.2 Remove dirty or disposable mops.
Maintenance
-16-
5.2 Clean the TOF sensor with a soft, dry cloth.
5.4 Clean the charging contact area with a soft, dry cloth.
5.3 Clean the return signal area with a soft, dry cloth.
6. Dust Bag replacement
6.1 Open cover 6.2 Lift the dust bag up 6.3 Throw the dust bag into the
trash can
6.3 Install new dust bag 6.4 Cover the lid
Maintenance
-16-
When the robot prompts that the dust bag is full, replace the dust bag in time. Dust bags are worn goods and
can be purchased from official channels.
9. Firmware upgrade
7. Clean dust collection dock channel and filter.
8. Battery maintenance
Maintenance
-17-
Dust
channel
cover
Screws×5
Filter
mouth
If the dock power is weaker after dust bag replacement,it is recommended to unplug the power plug and
reverse the device to check whether the dust channel is blocked by foreign bodies.
Remove the cover of the dust channel with a screwdriver,and remove the foreign matter. Take out the dust bag
to check whether there is foreign matter in the filter mouth and clean it.
8.1 In order to maintain battery performance, please keep the host charged and do not use excessive power.
8.2 If not used for a long time, please fully power off, and then store it.
8.3 Charge it at least every 3 months to avoid damage caused by over-discharge of the battery.
8.4 Please using matching power adapter while charging it.
8.5 The lithium battery does not need to be fully charged for 12 hours.
Access the firmware upgrade through the APP. When the new firmware is detected, boot the upgrade as
prompted. The firmware upgrade requires at least 50% of the power. It is better to upgrade the robot while
charging.
This manual suits for next models
2
Table of contents
Other Lydsto Vacuum Cleaner manuals
