M-Elec ML-2819SDIM User manual

S1 S2
S3
RF wireless LED remote controller
Four zones/areas
Press-button Dimmer
ML-2819SDIM
Parameter
Wiring diagram
Product Size
Brief introduction of buttons
Remote
Part No. Operation Voltage DIMENSIONS
ø/h (mm)
Operation
Frequency
ML-2819SDIM 4.5VDC 55x120x17
434MHz
Remarks
3 AAA (1.5V) batteries
Indicator: indicate the state of
remote control
Brightness button
ON/OFF of all zones
4 zones: each zone can save
3 color or modes
25% Brightness
Save button
50% Brightness
100% Brightness75% Brightness
55.0
17.0
120.0
Brightness wheel
Part No. Input Voltage Remarks
Current
ML-1009FAWi 12-36VDC Constant voltage
4x(60-180)W
4x5A
Output
Receiver(purchased separately)
12V/24V/36V
Power Supply
Constant Voltage
Single Color LED Strip
12-36 VD C
whi te
1234
wwcwwwcw
ML-1009FAWi
RF & WiFi Receiver
Operation
Learning (matching)
a. Do wiring according to connection diagram
b. Wake up the remote control by touching ON/OFF button.
c. Press learning button on receiver.
d. Touch any zone button on remote control.
e. Then touch brightness wheel.
f. Connected LED light will blink to confirm zone designation.
Choose zone number , for example, and , then touch , choose the brightness you
want, zone 1 and 3 will indicate corresponding brightness as we touched.
Brightness Up & Down Button
Long Press button to dim down/up brightness, the dimming direction will change every time after pressing
switch. For example, the first long press is brightness up, it will be dimmed down when long press again.
Dim wheel
Product introduction
The ML-2819SDIM remote controller has 4 different zones with quick brightness control buttons.
The remote controller can also save up to 3 modes into corresponding buttons ( S1, S2, S3) for each zone.
Quick brightness Wheel for finger control design.
5
ISO 900 1：200 8

Brightness level button
Select zone from . Press , the corresponding zones will be 25% brightness. Press ,
the corresponding zones will be 50% brightness. Press , the corresponding zones will be 75%
brightness. Press , the corresponding zones will be 100% brightness.
Save and recall button
select zones from adjust the color temperature
and brightness
long press one save button
from for 2-3 second
LED lighting flash twice
indicate save successful
a. Save Color temperature:
b.
then short press save button
Recall: select zone button which we want recall from ,
S1 S2
S3
S1 S2
S3
Safety & Warnings
1) The product shall be installed and serviced by a qualified person.
2) IP20. Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof
enclosure.
3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
4) Please check if the output voltage of any LED power supplies used complies with the working voltage of the
product.
5) Never connect any cables while power is on and always assure correct connections to avoid short circuits
before switching on.
6) Please ensure that the cable is secured tightly to the connector.
7) For latest information please visit our website www.melec.com.au.
Warranty Agreement
1) We provide lifelong technical assistance with this product:
5 year warranty. Every product has printed date on, for example: 1125 means year 2011, week 25.The warranty
is for free repair or replacement and covers manufacturing faults only. For faults beyond the 5-year warranty we
reserve the right to charge for time and parts.
2) Warranty is void if:
Any defects are caused by wrong operation.
Any damages are caused by unauthorized removal, maintenance, modifying, incorrect connection and
replacement of components.
Any damages are due to transportation, vibration etc. after purchase.
Any damages are caused by earthquake, fire, lightning, pollution and abnormal voltage.
Any damages are caused by negligence, inappropriate storing at high temperatures and humidity or near
harmful chemicals.
Product has been updated or changed.
3) Repair or replacement as provided under this warranty is the exclusive remedy to the customer.
Factory Reset
By pressing & holding the learning button on the ML-1009FAWI for over 5 seconds the connected LED Light will
flash, All previous Remote controls have now been deleted.