One Forall URC-3021 User manual

Jumbo Universal Remote Control
Catalog #1526
User’s Guide
This universal remote allows user to easily see and push buttons to control TV, VCR, DVD, Cable
and Satellite receivers. The large buttons are very sensitive to touch and have different colors for
different group functions. If you cannot hit the buttons, jacks on the back allow you to plug in your
special ability switches. Easy to program, easy to use. Size: 18"L x 10"W x 2"H. Requires 2 AA
Batteries.
νPlease refer to the manufacturer’s instruction manual included for rogramming
directions for this remote, with the exce tion of Ste #1: Installing the Batteries. Please
see below:
νInstalling the Batteries:
•You will not be lacing any batteries directly into the “One For All” remote as this is
ermanently affixed to the Jumbo Remote.
•Instead, lease locate the battery com artment recessed in the back of the Jumbo
Remote.
•The battery com artment cover is secured with a small screw. Use a Philli s head
screwdriver to remove this screw and remove the cover.
•Insert the 2 AA batteries into the com artment aying careful attention to ro er
battery olarity.
•Re lace the com artment cover and re-secure it with the screw.
•Test the unit by ressing the ON/OFF button. The red indicator light should blink. If
not, change your batteries.
•All rogramming will be done through the remote’s key ad on the back of this unit.
When rogramming make sure none of the large buttons on the front become
activated or de ressed, doing so will revent rogramming of your device.
νVolume Setting:
•To have control of your T.V. volume while running a DVD, VCR or CBL/SAT, you will
need to lock the Volume as described on ages 12 & 13 in the “One For All”
instructions. Press and hold SET button until the red light on the remote blinks twice,
then release. Enter 9-9-3 and then ress T.V. key once the Red light will blink twice.
Now when you ress Vol u , Vol down or Mute it will be controlled regardless of the
device you are controlling.

νSwitch Use:
•You can lug u to 13 se arate switches to control the same functions as the large
buttons; this is done via the in ut jacks located on the front side of the unit.
νTroubleshooting:
If you cannot get your Universal Remote to o erate any of your devices, or it will not
erform commands ro erly:
•Make sure that your batteries are fresh and installed correctly (according to ro er
olarity). *
•If you are using external switches with your remote, make sure they are lugged in
all the way, there should be no ga s. Test your switches on other switch ada ted
devices, to rule out your switches as the source of the roblem.
•Read the” One For All’s” troubleshooting section on age 15 of the guide for any
additional troubleshooting ti s.
•Try ALL of the codes listed for your device. Many set-u codes may allow artial
functionality; however, only one code will o erate your device correctly.
•Make sure that you are within 6-10 feet of your device, with the remote facing the
device, while rogramming. Make sure that you are within 15 feet of your device
when using your remote.
•If the red light on the remote control does not blink when you ress a key, re lace
the batteries with two (2) new AA alkaline batteries. Be sure to install aying close
attention to ro er battery olarity. *.
•* NOTE: When you re lace your batteries, or remove them for any reason, you must
re-install batteries within 10 minuets, or re- rogramming your remote will be
required. This is why it is im ortant to write down the codes that work for your
devices and kee both these manuals in a safe lace.
If you have any questions or technical roblems with your Universal Remote, or any of our
roducts, lease call our Technical Assistance De artment:
(1-800-832-8697)
customer_su [e-mail]
Enabling Devices & Toys for S ecial Children
385 Warburton Avenue
Hastings-on-Hudson, NY 10706
Tele hone 914-478-0960 – Fax [phone]
www.enablingdevices.com

1
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 1

TABLE OF CONTENTS
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features And Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Key Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Device Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Programming Device Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Searching For Your Code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Checking The Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Programming A Master Power Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Programming The Power Key For The Master Power Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Operating The Master Power Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Clearing The Master Power Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Re-Assigning Device Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Programming Favorite Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Changing Volume Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Locking Volume Control To One Mode
(Global Volume Lock). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Unlocking Volume Control For A Single Device
(Individual Volume Unlock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Unlocking All Volume Control
(Restoring Default Setting ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Clearing Custom Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Restoring Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Instructions To The User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Lifetime Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Manufacturer’s Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setup Codes For Cable Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setup Codes For Cable Box/PVR (or DVR) Combos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setup Codes For DVD Players . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setup Codes For DVD Player/VCR Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Setup Codes For PVRs (or DVRs). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setup Codes For Satellite Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setup Codes For Satellite Receiver/PVR (or DVR) Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setup Codes For TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setup Codes For TV/DVD Player Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Setup Codes For TV/VCR Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Setup Codes For TV/VCR/DVD Player Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Setup Codes For VCRs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 2

3
INTRODUCTION
The One For All 3 Device Universal Remote Control (URC-3021) is designed
to remotely operate up to three home entertainment devices. It also
features intuitive and easy-to-use keys for instant control of DVD and PVR
(or DVR) components. Moreover, its sophisticated technology will allow you
to consolidate your original home entertainment remote controls into one
easy-to-use product. Advanced features include:
• Intuitive buttons to allow easy access to functions and menus on your DVD
player, PVR (or DVR), and Cable/Satellite devices
• Direct code setup for easy device programming
•Step-and-Set code search and Code Verification for an alternate way to pro-
gram devices
•Power Macro for master on/off control of all of your equipment with a single
keystroke
•Volume Lock/Unlock feature to lock or unlock the volume control to one mode
or individual modes
•Device Key Re-Assignment to remotely control a second (duplicate) device
•Channel Scan and Favorite Channel Scan for easy channel surfing
• Color-coded keys to quickly locate popular functions
• Extensive code library for popular video devices including DVD players and
PVRs (or DVRs)
The URC-3021 remote control requires two (2) new AAA alkaline batter-
ies (not included) and some easy programming to control your devices.
For best results, please read and perform all instructions listed here. Also,
keep this guide for future reference.
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 3

4
FEATURES AND FUNCTIONS
Use the illustration below to locate features on the One For All 3 Device
Universal Remote Control (URC-3021) and then study the Key Charts (on
the next two pages) to learn how they function.
To find out what type of devices can be controlled by each device key after
programming, see the Device Table on page 6.
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 4

5
Key Charts
When the LED (red light) blinks, the remote control
is working and (after programming) is sending
signals.
Press DVD/VCR,CBL/SAT,orTV once to select a
desired home entertainment device to control.
Also see the Device Table on page 6.
Press POWER once to turn on or off the selected
device. For master power control,see Programming
A Master Power Macro on page 10.
Use the keypad (1~ 9and 0) to directly select
channels (e.g., 009 or 031).
Use TV/VID to switch the TV’s input to view TV or
video programs.
Press ENTER once after entering the channel
numbers on some TVs.
Use GUIDE to display your selected device’s
program guide or setup menu.
Press MENU once to display your selected device’s
main menu.
Use INFO to display the current channel and
program or on-screen directory.
Use EXIT to exit from your selected device’s guide
or menu.
Use the Cursor Keys to move the cursor in the pro-
gram guide and menu screens.
Use SELECT (OK) to choose options from your
selected device’s menu or guide.
Press LAST once to recall the last channel.
Use FAV to scan all channels, or after programming,
to scan up to10 favorite channels.
Use CH▲(or CH▼) to select the next higher (or
lower) channel.
Press SUBTITLE/CC once to display (or turn off) sub-
titles or closed captions, if available on your DVD
player or cable/satellite service.
For a PVR (or DVR), press PVR MENU once to dis-
play a list of your recorded shows.
Press MUTE once to turn the sound off or on.
Use VOL▲(or VOL▼) to raise (or lower) the sound
volume.
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 5

6
Use REW,PLAY,FWD,PAUSE,or STOP to control your VCR,
PVR (or DVR), or DVD player.
For a DVD player, use SKIP F. or SKIP R. to view the next
or previous chapter.
For a VCR, PVR (or DVR), or VOD (if available), use SCAN-
or SCAN+ to quickly scan forward or back through a video
program. Use REPLAY for an instant replay. Use QUICK
SKIP to advance the video program a preset amount (as
set on your device).
Press REC twice to record a VCR or PVR (or DVR)
program.
Use SLEEP to set the sleep timer on a selected device if
equipped with this feature.
Use SET for all programming sequences.
Device Table
NOTE: Please refer to the table below when performing the instructions in“Programming
Device Control”on page 8.
After programming, the One For All 3 Device Universal Remote Control will
be able to control the following types of devices:
DEVICE KEY CONTROLS THESE TYPES OF DEVICES
• DVD Player
•VCR
• PVR (or DVR)
• TV/DVD Player Combo
• VCR/DVD Player Combo
• TV/VCR Combo
• TV/VCR/DVD Player Combo
• VCR/DVD Player Combo
• Cable Box (or Converter)
• Cable Box/PVR (or DVR) Combo
• Satellite Receiver
• Satellite Receiver/PVR (or DVR) Combo
• Television
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 6

7
INSTALLING BATTERIES
1. On the remote control’s back, push the tab and lift off the
battery cover.
2. Obtain two (2) new AAA alkaline batteries. Match the +
and – marks on the batteries to the + and – marks in the
battery case, then insert the new batteries.
3. Press the battery cover back into place. The tab should
click when the cover is locked.
4. Test the remote control by pressing any mode key (e.g.,
TV). If the batteries are inserted correctly, the LED (red
light) will blink.
NOTE: When batteries need replacement, the remote control will stop operat-
ing. Remove the old batteries and insert new ones within 10 minutes to
ensure all of your programming information is restored.
❶
❸
❷
❷
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 7

8
PROGRAMMING DEVICE CONTROL
The One For All 3 Device Universal Remote Control is preprogrammed at
the factory to operate an RCA TV, a Toshiba DVD player, and a Motorola
cable box. To control devices other than the default brands, perform the fol-
lowing steps; otherwise skip this section:
1. Turn on a desired device (e.g.,VCR or DVD player) and, if
applicable, insert media (e.g., cassette or disc).
NOTE: Please read steps 2 through 4 completely before proceeding.
Highlight or write down the codes and device you wish to program
before starting step 2.
2. On the remote control, press a device key once (i.e.,DVD/VCR,
CBL/SAT,orTV).
NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo,
or TV/VCR/DVD Player Combo press DVD/VCRonce. After program-
ming a VCR Combo device, you will be able to control channel selec-
tion, volume, and VCR functions.
NOTE: To program control of a DVD Player, DVD Player/VCR
Combo, or TV/DVD Player Combo, press DVD/VCR once. After pro-
gramming a DVD Combo device, you will be able to control channel
selection, volume, and DVD functions.
NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR)
Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SATonce.
3. Press and hold SET until the LED (red light) blinks twice,
then release SET.
4. Use the Manufacturer’s Codes (starting on page 18) to
locate the type of device and brand name and then enter
the first four-digit code for your device. If performed cor-
rectly, the LED will blink twice.
NOTE: If the LEDdid not blink twice, repeat steps 2 through 4 and enter
the same code again.
5. Aim the remote control at the device and press POWER
once. The device should turn off. If it does not, repeat
steps 2 through 5, trying each code for your brand until
you find one that works. If it still doesn’t work, try
Searching For Your Code on next page.
NOTE: If the device does not have a POWERkey, press PLAY.
6. Repeat steps 1 through 5 for each device you want to con-
trol.For future reference, write down each working device
code in the following boxes:
DVD/VCR Code:
Device Type:__________________
CBL/SAT Code:
Device Type:__________________
TV Code:
Device Type:__________________
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 8

9
SEARCHING FOR YOUR CODE
If your device does not respond to the remote control after trying all codes
listed for your brand, or if your brand is not listed at all, try searching for
your code.
NOTE: Before performing a code search for a DVD player or a VCR, turn on the device and
insert the required media.
For example,to search for a code for your TV:
1. On the remote control,press TV once.
2. Press and hold SET until the LED (red light) blinks twice,
then release SET.
3. Enter 9- 9- 1.TheLED will blink twice.
4. Aim the remote control at the TV and slowly alternate
between pressing POWER and TV. Stop when the TV turns off
(after pressing POWER).If the device does not have a Power
key, you can substitute another function, such as digits 0~ 9,
CH▲,orPLAY).
NOTE: In the search mode,the remote control will send IR codes from
its library to the selected device, starting with the most popular code
first.
5. To lock in the code, press and release SET.TheLED will
blink twice.
6. To search for the codes of your other devices, repeat steps
1 through 5, but substitute the appropriate device key for
the device you are searching for.
CHECKING THE CODES
If you have set up the remote control using the Searching For Your Code pro-
cedure as above, you may need to find out which four-digit code is operat-
ing your equipment. For example,to find out which code is operating your
TV:
1. On the remote control,press TV once.
2. Press and hold SET until the LED (red light) blinks twice,
then release SET.
3. Enter 9- 9- 0.TheLED will blink twice.
4. To view the code for the first digit, press 1once. Wait 3
seconds, count the LED blinks (e.g., three blinks = 3) and
write down the number in the leftmost box in the TV
code boxes on page 8.
NOTE: If a code digit is“0”, the LEDwill not blink.
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 9

10
5. Repeat step 4 (on the previous page) three more times for
remaining digits. Use 2for the second digit,3for the third
digit, and 4for the fourth digit.Write down the code dig-
its in the remaining TV code boxes on page 8.
6. To check for codes of other devices,repeat steps 1
through 5 (starting on the previous page), but substitute
the appropriate device key for each device you are check-
ing.Write down the device’s code digits in the appropriate
code boxes on page 8.
PROGRAMMING A MASTER POWER MACRO
In its default state, the POWER key on the One For All 3 Device Universal
Remote Control will individually power your home entertainment devices
on or off. However, you can also program a Master Power Macro onto the
POWER key that will sequentially turn on or off all the devices with a single
key press.
Programming The Power Key For The Master Power Macro
1. Press and hold SET until the LED (red light) blinks twice,
then release SET.
2. Enter 9- 9- 5.TheLED will blink twice. Then press POWER
once.
3. For the first device you want in the power-on sequence,
press its device key (e.g.,CBL/SAT) once.
4. Repeat step 3 up to two more times to add desired
devices to the power-on sequence (e.g., DVD/VCR and TV).
5. To save the settings and exit the program, press and hold
SET until the LED blinks twice, then release SET.
Operating The Master Power Macro
1. After programming, point the remote control at the
devices and press POWER for at least 2 seconds to sequen-
tially turn on (or off) your devices.
NOTE: When POWERis pressed for less than 2 seconds, a power com-
mand will only be sent to the currently-selected device. This allows
you to still individually power devices on or off.
2. Devices will turn on (or off) according to your pro-
grammed sequence.
NOTE: The currently-selected device will always turn on or off first,
followed by the remaining programmed sequence. After the master
power sequence has been completed,the remote control will be set to
control the first powered-on device.
NOTE: If one or more devices does not have a POWERkey, the power
off/on sequence may be slightly delayed when the remote control signals
the device(s). This action is normal.
continued on next page...
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 10

11
PROGRAMMING A MASTER POWER MACRO (cont’d)
Clearing The Master Power Macro
1. Press and hold SET until the LED (red light) blinks twice,
then release SET.
2. Enter 9- 9- 5.TheLED will blink twice. Then press POWER
once.
3. Press and hold SET until the LED blinks twice, then release
SET.TheMaster Power Macro is now cleared.
RE-ASSIGNING DEVICE KEYS
The One For All 3 Device Universal Remote Control can be set to control a
DVD player and a VCR (or a PVR) or a second DVD player by re-assigning
the unused CBL/SAT key as follows:
1. On the remote control,press and hold SET until the LED
(red light) blinks twice, then release SET.
2. Enter 9- 9- 2.TheLED will blink twice.
3. Press DVD/VCR once.
4. Press CBL/SAT once. The LED will blink twice. The CBL/SAT key
is now ready to be set up to control yourVCR (or PVR) or
second DVD player.See Programming Device Control on page
8.
NOTE: Only one device can be assigned to an unused device key at a time.
USING CHANNEL SCAN
In the CBL/SAT or TV mode, use the FAV key to start a 3-second scan of all
channels. Or, if programmed, use the FAV key to scan only your favorite
channels to view a desired channel (see Programming Favorite Channel Scan
on next page. )
1. Press CBL/SAT or TV once.
2. Press FAV once.
•IfFavorite Channel Scan has been set up, scanning of favorite
channels will start with up to 100 channel changes or until
stopped by pressing any key.
•IfFavorite Channel Scan has not been set up, scanning
will start with the current channel, and continue up to
100 channel changes or until stopped by pressing any key.
3. To stop scanning channels at any time, press any key once.
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 11

12
PROGRAMMING FAVORITE CHANNEL SCAN
In the CBL/SAT or TV mode, you can store a list of up to 10 favorite channels,
in any order, that will be immediately scanned when FAV is pressed (see
Using Channel Scan on the previous page).
NOTE: Favorite channels can only be programmed for one mode.After programming, if FAV
is pressed while in another mode, the remote control will start scanning all channels instead
(if applicable to the selected device).
1. On the remote control,press CBL/SAT or TV once.
2. Press and hold SET until the LED (red light) blinks twice,
then release SET.
3. Enter 9- 9- 6.TheLED will blink twice.
4. Use the keypad to enter a favorite channel number (e.g.,
031). Then press SET once.
NOTE: If the original remote control required pressing an Enter key
to change the channel, also press the ENTER key after the channel
number (e.g., 0 - 3 - 1 - ENTER). On some satellite receivers and cable
boxes, you may need to press the SELECT(OK) key instead of ENTER.
5. If desired,repeat step 4 for each channel to be stored, up
to a total of 10 channels.
NOTE: If you try entering more than 10 channels, the remote control
will automatically exit programming. To change your favorite chan-
nel list at this point, you will first need to delete the existing list by
performing the steps in “Clearing Custom Programming” on page 14.
Then, perform the instructions in this section once again.
6. To exit programming with less than 10 favorite channels
stored, press and hold SET until the LED blinks twice.
Otherwise, the remote control will automatically exit the
program after 10 channels have been stored.
CHANGING VOLUME LOCK
The One For All 3 Device Universal Remote Control is set at the factory for
independent volume control of each selected device. However, you may
change the Volume Lock setting to Global Volume Lock so that a device’s vol-
ume will be locked to one mode (e.g., to control TV volume in all other
modes).After that, if desired, you can perform Individual Volume Unlock on
a selected device to set its volume control for independent operation.
Locking Volume Control To One Mode
(Global Volume Lock)
1. Press and hold SET until the LED (red light) blinks twice,
then release SET.
continued on next page...
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 12

13
CHANGING VOLUME LOCK (cont’d)
Locking Volume Control To One Mode
(Global Volume Lock)
2. Enter 9- 9- 3and then press any mode key once (e.g., TV).
The LED will blink twice.
3. Now, when you press VOL▲,VOL▼,orMUTE, the volume of
the selected device (e.g., TV) will be controlled, regardless
of the mode you have selected.
Unlocking Volume Control For A Single Device (Individual Volume
Unlock)
1. After performing Global Volume Lock (above),press a desired
mode key where you want volume to be unlocked (e.g.,
DVD/VCR) and controlled within its own mode.
2. Press and and hold SET until the LED (red light) blinks twice,
then release SET.
3. Enter 9- 9- 3and then press VOL▼once. The LED will
blink four times.
4. If desired, repeat steps 1 through 3 (of this section) for
each device that you want volume to be unlocked.
5. After selecting a device that has volume unlocked (e.g.,
DVD/VCR), pressing VOL▲,VOL▼,orMUTE will control the
device’s volume only in its own mode.
Unlocking All Volume Control (Restoring Default Setting)
NOTE: Performing these instructions will restore independent volume control for all pro-
grammed devices (e.g., TV volume control in TV mode,VCR volume in DVD/VCR mode,
etc.).
1. On the remote control, press and hold SET until the LED (red
light) blinks twice,then release SET.
2. Enter 9- 9- 3and then press VOL ▲once. The LED will
blink four times.
3. Volume will again be independently controlled according
to its default states for all programmed devices.
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 13

14
CLEARING CUSTOM PROGRAMMING
The One For All 3 Device Universal Remote Control contains an Operational
Feature Reset program. If desired, you can use it to clear custom program-
ming, except your setup codes and reassigned device keys, and reset them
to original factory settings.Also see Restoring Factory Default Settings below.
IMPORTANT: Executing this program will erase all your custom settings for
Power Macro, Favorite Channels, and Volume Lock.
1. Press and hold SET until the LED (red light) blinks twice,
then release SET.
2. Enter 9- 8- 0.TheLED will blink twice. The remote con-
trol will return to normal operation.
RESTORING FACTORY DEFAULT SETTINGS
The One For All 3 Device Universal Remote Control also contains a Factory
Reset program that you can use to reset all custom settings and setup codes
to original factory settings.Also see Clearing Custom Programming above.
IMPORTANT: Executing this program will erase all your custom settings for
Power Macro, Favorite Channels, Volume Lock, Reassigned Devices, and all
device settings.
1. Press and hold SET until the LED (red light) blinks twice,
then release SET.
2. Enter 9- 8- 1.TheLED will blink twice. The remote con-
trol will return to normal operation.
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 14

15
TROUBLESHOOTING
PROBLEM: LED (red light) does not blink when you press a key.
SOLUTION: Replace batteries with two new AAA alkaline batteries.
PROBLEM: LED blinks when you press a key, but home entertain-
ment device does not respond.
SOLUTION: Make sure the remote control is aimed at your home
entertainment device and is not farther than 15 feet
away.
PROBLEM: The unit does not control home entertainment devices
or commands are not working properly.
SOLUTION: Try all listed codes for the device brands being set up.
Make sure they can be operated with an infrared remote
control.
PROBLEM: Changing channels does not work.
SOLUTION: If original remote required pressing ENTER or SELECT to
change channels, press ENTER or SELECT on this remote after
entering the channel number.
PROBLEM: Tried Searching For Your Code method and still could not
find a working code.
SOLUTION: Clear the device key as follows: Press and hold SET until
the LED (red light) blinks twice,then release.Next enter
9- 9- 2. Then press the device key to be cleared twice.
Now repeat the Searching For Your Code method on page
9.
PROBLEM: CH▲and CH▼do not work for your RCA TV.
SOLUTION: Due to RCA design (1983-1987), only the original
remote control will operate these functions.
PROBLEM: No remote control of volume.
SOLUTION: See Changing Volume Lock on page 12 to lock/unlock
volume.
For assistance, please contact us in any of the following ways:
• E-mail: ofasup[email protected]m
• Internet: http://www.oneforall.com
• Consumer Help Line: [phone]
INSTRUCTIONS TO THE USER
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to part 15 of the FCC Rules.These limits are designed to
provide a reasonable protection against harmful interference in a residential
installation.This equipment generates, uses, and can radiate radio frequency
energy and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.However, there is no guar-
antee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase separation between equipment and receiver.
• Connect equipment into an outlet or a circuit different from that to which the
receiver is connected.
• Consult dealer or experienced radio/TV technician for help.
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 15

16
LIFETIME WARRANTY
One For ALL ("OFA") warrants this product to be free from defects in materials
and workmanship, under normal use, throughout the period of the product’s
ownership by the original purchaser. This warranty does not cover damages or
failures caused by products or services not supplied by OFA, or which result from
accident, misuses, abuse, neglect, mishandling, misapplication, faulty installation,
set-up adjustment, improper maintenance, alteration, maladjustment of con-
sumer controls,modifications, commercial use,or that is attributable to acts of
God.
There are no express warranties except as listed above. OFA SHALL NOT BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF
WARRANTY,ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE,ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion or limitation of incidental or consequen-
tial damagers, or limitations on how long an implied warranty lasts, so the above
exclusions or limitations may not apply to you. This warranty gives you specific
legal rights and you may also have other rights which vary from state to state.
To obtain warranty service for a defective product, please return the product,
preferably in the original carton,along with your purchase receipt, to the store of
original purchase for the first 90 days.A note detailing the complaint would be
helpful. The store, at its option, will replace or repair this product if found to be
defective.
If the unit has been purchased more than 90 days ago,please return it to CT
Global Inc.8918 Stone Green Way, Louisville, KY 40220 together with the original
receipt and $3.95 to cover postage and handling. It will be repaired or replaced at
the manufacturer’s option.The manufacturer reserves the right to substitute a
currently manufactured model with equal or superior features.
One For All: [phone]
URC-3021 March 2004
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 16

17
ADDITIONAL INFORMATION
As you update your home entertainment system, One For All® has a universal
remote control that will fit your needs. Look for these exciting products at a
retailer near you:
One For All Access 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-3605
One For All Big Easy 3-Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-3300
One For All DVD Expert 4-Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-4041
One For All Big Easy 4-Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-4330
One For All Access 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-4605
One For All Access 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-5705
One For All 4 Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-4021
One For All 3 Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-3021
One For All PVR 6-Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-6131
One For All 6-Device Home Theater. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-6011
One For All 8-Device Home Theater. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-8011
One For All 8L-Device Home Theater
With Learning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-8811
One For All A/V LCD 8 Device
With Learning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-8910
One For All IR/RF LCD 8 Device
With Learning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-9910
One For All 8 Device Home Theater Remote
Powered By Kameleon. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-9960
ONE FOR ALL® is the registered trademark of Universal Electronics Inc.
Computime International Ltd.is the Licensee of the ONE FOR ALL® brand for
USA and Canada.
Copyright 2004 by Universal Electronics Inc.No part of this publication may be
reproduced,transmitted,transcribed, stored in any retrieval system, or translat-
ed to any language,in any form or by any means, electronic,mechanical, mag-
netic, optical, manual, or otherwise, without the prior written permission of
Universal Electronics Inc.
The One For All® 3 Device Universal Remote Control is compatible for use in
North America, excluding Mexico.
This One For All® 3 Device Universal Remote Control is covered by one or more
of the following US Patents:
6,587,067 6,496,135 5,515,052 5,959,751
6,587,067 5,481,256
CTGAE3P 3021 manual booklet 5/24/04 12:46 PM Page 17