M-Sure MS-535 Series User manual

m-sure.co.uk
www.m-sure.co.uk - Allendale Group Ltd, Pindar Road, Hoddesdon, Hertfordshire. EN11 0BZ.
Images & Content ©2020 Allendale Group Limited. E&OE - Specifi cations subject to change without prior notice.
M-SURE Digital Depth Gauges
M-SURE Digital Depth Gauges
• Before using the Digital Depth Gauge for the rst time, wipe with a clean cloth ideally soaked with cleaning oil.
• Digital Depth Gauges are precision measuring instruments. Avoid using excessive force, and treat with care.
• The tted battery is intended for the factory test procedure and therefore may not meet the specied battery life.
• Avoid exposure to all liquids, excessive humidity or temperature.
• Avoid exposure to bright sunlight.
• Never apply voltage on any part of this Depth Gauge or electric engrave.
• Remove the battery if the Gauge is not being used for a long period of time.
• Never use solvents to clean. Only use a soft cloth with cleaning oil.
Precautions
Digital Depth Gauge
Standard Depth Gauge
Depth Measurement
Add hook thickness to
the displayed value
Add hook thickness to
the displayed value
Depth
1 3
4
8
5
76
10
9
2
1
2 3
4 5 6
7
8
1. Frame. 2. Anvil. 3. Spindle. 4. LCD Display.
5. Thimble. 6.Ratchet. 7. SPC Output.
8. Function Buttons.
1
2
3
4
5
7
8
9
10
1. Probe Extension. 2. Function Buttons. 3. LCD Display.
4. Slider. 5. Battery Cover. 6. Locking Screw.
7. Guiding Face. 8. Beam. 9. Instrument Base.
10. Instrument Base Reference Plane.
6
Depth Gauge with hook
Part No: MS-535, 540 & 542 Series
Doc V: 1.0
1. Insert the key into the battery cover.
2. Twist to unlock. DO NOT use
excessive force.
3. Lift out the battery cover. 4. Remove the battery. (A magnet tip tool can
be used)
5. Locate the side spring battery contact.
6. Insert the replacement battery with
its edge against the side battery contact.
7. Press down on the opposite edge.
8. Locate the two lugs on the battery
cover with the two slots on the Depth
Gauge. Insert the battery cover.
9. Twist to lock. DO NOT use excessive
force.
1
2
6
7
8
34
5
Battery Replacement
1. Base
2. Reading head
3. Locking screw
4. LCD display
5. Data port
6. Beam
7. Battery cover
8. Function buttons
9. Hook
1
9
Thickness:
2mm
2
3
86
7
4
5
9

m-sure.co.uk
www.m-sure.co.uk - Allendale Group Ltd, Pindar Road, Hoddesdon, Hertfordshire. EN11 0BZ.
Images & Content ©2020 Allendale Group Limited. E&OE - Specifi cations subject to change without prior notice.
M-SURE Digital Depth Gauges
Referencing Standard Depth Gauge
Referencing Depth Gauge with hook
1. Ensure the locking screw is loose.
2. Wipe clean surface plate or similar at
service.
3. Ensure Gauge base is clean.
4. Place Gauge base on the surface plate.
5. Slide the beam downwards so
measuring contact is in contact with the
surface plate.
6. Press the zero button.
1. Ensure the locking screw is loose.
2. Ensure the Gauge base and hook is
clean.
3. Close the Gauge.
4. Press the zero button.
Metric/Inch Conversion
25.40mm
in/mm

Press in/mm to convert from
inch to metric display.
1.000
The display will indicate
which units are being
displayed.
in/mm

in
Trouble Shooting
Problem Possible Cause Solution
Flashing display Low voltage
Poor contact
Replace battery
Clean contact
No display Dead or weak battery
Poor contact
Replace battery
Clean contact
Erratic or frozen display Contamination between beam & head
low voltage
Wipe Depth Gauge clean
Replace battery
Erroneous reading Low voltage
Contamination between beam & head
Too much operating force
Low ambient temperature
Replace battery
Wipe Depth Gauge clean
Use pressure device
Store Depth Gauge at normal room
temperature