M-system F2AP User manual

F2AP
EM-5436 Rev.4
P. 1 / 2
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: inf[email protected].jp
DC/FREQUENCY CONVERTER MODEL F2AP
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
Signal conditioner ...............................................................(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
The actual installation environments such as panel configu-
rations, connected devices and connected wires may affect
the protection level of this unit when it is integrated in a
panel system. The user may have to review the CE require-
ments in regard to the whole system and employ additional
protective measures to ensure CE conformity.
■POWER INPUT RATING & OPERATIONAL RANGE
Locate the power input rating marked on the product and
confirm its operational range as indicated below:
24V DC rating: 24V ±10%, approx. 80mA
■GENERAL PRECAUTIONS
Before you remove the unit or mount it, turn off the power
supply and input signal for safety.
■ENVIRONMENT
•Indoor use
•When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
•Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
•Environmental temperature must be within -5 to +55°C
(23 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
•Be sure that the ventilation slits are not covered with ca-
bles, etc.
■WIRING
•Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
•Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
The unit is designed to function as soon as power is sup-
plied, however, a warm up for 30 minutes is required for sat-
isfying complete performance described in the data sheet.
COMPONENT IDENTIFICATION
Body
Zero Adj.
Span Adj.
Connection
Diagram
Specifications
Euro Type
Terminal Block
INSTALLATION
Set the unit so that its DIN rail adaptor is at the bottom.
Position the upper hook at the rear side of the unit on the
DIN rail and push in the lower.
When removing the unit, push down the DIN rail adaptor
utilizing a minus screwdriver and pull.
DIN Rail
35 mm wide
Spring Loaded
DIN Rail Adaptor
TERMINAL CONNECTIONS
Connect the unit as in the diagram below or refer to the con-
nection diagram on the side of the unit.
+
–
+
–
OUTPUT
5
6
POWER
7
8
+
–
INPUT
1
2
• Open Collector
Output Connection
Examples
+
–
5
6
+
–
• Voltage Pulse
+
–
5
6
+
–
SCREWDRIVER (–)
PIN TERMINAL
MULTI-STRAND CABLE
1.25 mm2(.02 in2)
PHOENIX CONTACT
AI 1,5-8BK recommended
SOLID CABLE
1.4 mm (.06) dia.
8 mm (.32)
STRIPPED LENGTH
• Wiring Procedure for Euro Type Terminal Block

F2AP
EM-5436 Rev.4
P. 2 / 2
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: inf[email protected].jp
CHECKING
1 ) Terminal wiring: Check that all cables are correctly
connected according to the connection diagram.
2 ) Power input voltage: Check voltage across the terminal
7 – 8 with a multimeter.
3 ) Input: Check that the input signal is within 0 – 100% of
the full-scale.
4 ) Output: Check that the load resistance meets the de-
scribed specifications shown below.
Check also that the receiving instrument is able to ac-
cept the waveform as explained in the figure below.
OUTPUT LOAD REQUIREMENTS
Open collector 30V DC @100mA max.
5V pulse 250Ω min.
• Open Collector • Voltage Pulse
OFF
ON
20 %
80 %
1 / f
■ Frequency less than 500 Hz at 100% input
Duty ratio 20% (See the figure below)
H Level
L Level
20 %
80 %
1 / f
• Open Collector • Voltage Pulse
■ Frequency greater than 500 Hz at 100% input
See the figure and equation below.
H Level
L Level
Pulse Width
OFF
ON
Pulse Width
Pulse Width [millisec.] = 1
2.09 x 100% Frequency [kHz]
↓↓
ADJUSTMENT PROCEDURE
This unit is calibrated at the factory to meet the ordered
specifications, therefore you usually do not need any cali-
bration.
For matching the signal to a receiving instrument or in case
of regular calibration, adjust the output as explained in the
following.
■HOW TO CALIBRATE THE OUTPUT SIGNAL
Use a signal source and measuring instruments of sufficient
accuracy level. Turn the power supply on and warm up for
more than 30 minutes.
1 ) ZERO: Apply 5% input and adjust output to 5%.
2 ) SPAN: Apply 100% input and adjust output to 100%.
3 ) Check ZERO adjustment again with 5% input.
4 ) When ZERO value is changed, repeat the above proce-
dure 1) – 3).
MAINTENANCE
Regular calibration procedure is explained below:
■CALIBRATION
Warm up the unit for at least 30 minutes. Apply 0%, 5%,
25%, 50%, 75% and 100% input signal. Check that the out-
put signal for the respective input signal remains within
accuracy described in the data sheet. When the output is
out of tolerance, recalibrate the unit according to the “AD-
JUSTMENT PROCEDURE” explained earlier.
EXTERNAL DIMENSIONS unit: mm (inch)
1234
5678
107 (4.21) [1.5 (.06)]
DIN RAIL
35mm wide
22.5 (.89)
75 (2.95)
• When mounting, no extra space is needed between units.