M-system R8-CT4E User manual

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9794 Rev.1 P. 1 / 5
INSTRUCTION MANUAL
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
AC current input module .................................................. (1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
• The equipment must be mounted inside a panel.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform-
ity.
■GENERAL PRECAUTIONS
• Before you remove or mount the unit, turn off the power
supply and input signal for safety.
• Switches on the side of the module can be set for mainte-
nance only while the power supply is off. Do not access
them while the power is supplied.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 30 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.
INSTALLATION
■HOW TO MOUNT THE MODULE ON DIN RAIL
A
B
• I/O Module
Confirm that the locking clamps of the I/O module are set.
Insert the module in parallel to the next one while aligning the grooves of
both modules (A & B in the above figure).
Maintain it perpendicularly to the rail.
More I/O modules can be added in the same manner.
AC CURRENT INPUT MODULE
(4 points, RMS sensing, clamp-on current sensor, non-isolated)
MODEL R8-CT4E

R8-CT4E
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9794 Rev.1 P. 2 / 5
• Protective Cover
The protective power is to be attached over the connected I/O module
at the right end.
Align the hooks on the cover with the grooves of the module and slide it
straight until the hooks are latched.
When removing the cover, pull it out while squeezing the hooks inward.
Groove
Hook
■HOW TO UNMOUNT THE MODULE ON DIN RAIL
Release the locking clamps and pull out straight the module.
Caution !
1) Be careful not to hurt your hand by pointed edges of the internal bus
connector.
2) I/O modules cannot hold tightly on the DIN rail by themselves without
power/network module.
Secure them to the position if necessary by using DIN rail end plates.
• Removing an intermediate module

R8-CT4E
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9794 Rev.1 P. 3 / 5
COMPONENT IDENTIFICATION
FRONT VIEW SIDE VIEW
CT1
RUN
CT2
CT3
CT4
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
Status Indicator LED
Input Status Indicator LED
Internal Bus Connector
Input Connectors
Module Address Setting
Rotary SW
SW1
x10 x1
SW2
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
CARD ADD.
Terminator DIP SW
SW3Term
On
Function Setting
DIP SW
12345678
SW4
On
■INDICATOR LED
LED OPERATION FUNCTION
Status OFF Stopping
Green ON Valid host communication
Green Blinking
Reading/writing configuration
Red ON Setting error
Red Blinking Parameter error
Input
Status
OFF Input data in the range
Red Blinking Input data out of range
■INPUT CONNECTOR ASSIGNMENT
PIN ID FUNCTION
No.
1 kInput
2 NC No connection
3 NC No connection
4 lInput
1
2
3
4
■MODULE ADDRESS
The left switch determines the tenth place digit, while the
right switch does the ones place digit of the address.
Address is selected between 0 to 30.
(Factory setting: 0)
Module Address Setting (x10)
Module Address Setting (x1)
5
4
3
2
1
0
9
8
7
6
5
4
3
2
1
0
9
8
7
6
■OPERATING MODE
(*) Factory setting
• Clamp-on Current Sensor Setting
Same range for all channels. Use PC Configurator to set
independent ranges per channel.
CLUMP-ON CURRENT SENSOR SW4
123
CLSE-R5 : 0 − 5A AC (*) OFF OFF OFF
CLSE-05 : 0 − 50A AC ON OFF OFF
CLSE-10 : 0 − 100A AC OFF ON OFF
CLSE-20 : 0 − 200A AC ON ON OFF
CLSE-40 : 0 − 400A AC OFF OFF ON
CLSE-60 : 0 − 600A AC ON OFF ON
• Conguration Mode
CONFIGURATION MODE SW4-8
DIP switch setting (*) OFF
PC Configurator and communication ON
Note: Be sure to set unused SW4-4 through 4-7 to OFF.
■TERMINATOR DIP SW
TERMINATOR SW SW3
Without (*) OFF
With ON

R8-CT4E
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9794 Rev.1 P. 4 / 5
PC CONFIGURATOR
With configurator software, settings shown below are available.
Refer to the software manual of R8CFG for detailed operation.
■CHANNEL INDIVIDUAL SETTING
PARAMETER AVAILABLE RANGE DEFAULT SETTING
Sensor type CLSE-R5
CLSE-05
CLSE-10
CLSE-20
CLSE-40
CLSE-60
CLSE-R5
Lower range value Depends on sensor type 0.000
Upper range value Depends on sensor type 0.000
Fine zero adjustment -320.00 to +320.00 (%) 0.00 (%)
Fine gain adjustment -3.2000 to +3.2000 1.0000
Scaled range Zero -32000 to +32000 0
Scaled range Span -32000 to [phone]
Low-end cutout 0.0 to 5.0 (%) 1.0 (%)
■CHANNEL BATCH SETTING
PARAMETER AVAILABLE RANGE DEFAULT SETTING
Loss of internal bus communication detection time 0.0 to 99.9 (sec.) 1.0 (sec.)
Configuration mode DIP switch (OFF)
PC (ON)
DIP switch (OFF)
Note: Turn SW4-8 ON to allow programming by the PC Configurator via the Power/Network Module.
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
■EXTERNAL DIMENSIONS unit: mm (inch)
115 (4.53)6 (.24)
7 (.28)
6 (.24) 7 (.28)
DIN RAIL
(35 mm wide)
[3 (.12)] [4 (.16)] 12 (.47) 59 (2.32)
55 (2.17)

R8-CT4E
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9794 Rev.1 P. 5 / 5
■CONNECTION DIAGRAM
CT
k
l
CT
k
l
1
2
4
3
1
2
4
3
INPUT 1
INPUT 4
LOAD
SOURCE
LOAD
SOURCE
NC
NC
NC
NC
*Not used
INTERNAL POWER
INTERNAL BUS
EXC. SUPPLY *
BUS CONNECTOR
INPUT
CONNECTOR 1
INPUT
CONNECTOR 4
WIRING INSTRUCTIONS
■e-CON connector
Unit side connector: XN2D-1474-S002 (Omron)
Recommended cable side connector: XN2A-1470 (Omron)*1
Applicable wire size: 0.08 to 0.5 mm2(AWG28 to 20)
Outer sheath diameter: max. 1.5 dia
*1. The cable side connector is not included in the package.
Refer to the specifications of the product.