M2SYNTH 191 User manual

8-Step Analogue Sequencer 191 V1d 1
8-Step Analog Sequencer
191
Kit Assembly Instructions

8-Step Analogue Sequencer 191 V1d 2
Features
3U wide 8-step analogue sequencer
Internal or external clock
Internal clock (tempo) from 3 BPM (0.05Hz) to 21,000 BPM (350Hz)
External clock from to >100khz (recommended < 50kHz)
Internal clock voltage controlled (tempo) range dependant on tempo pot position
Tempo 0%: 0V = 0.05Hz, 10V = 80Hz
Tempo = 50%: 0V = 1Hz, 10V = 1kHz (maximum)
Clock output socket
Gate and trigger outputs, trigger pulse with 2mS.
Gate output adjustable from 5 to 95% using pot or external CV. External gate CV
With gate width control set to 0% (fully CW), external CV gives 5 to 95% for
an CV of 0-10V
CV output with range switch 0-3V or 0-10V
Additional CV output with adjustable glide control (1 to 700mS)
Operates on +/-12V (M²Synth power header) or on +/-15V via integral MOTM and
Dotcom headers (select voltage using on-board jumpers)
Kit Contents
Description
Reference
MOTM
Qty
MU
Qty
Notes
Components Kit
7216-191-1
1
1
See BOM
Accessories Pack including:
7216-191-2
1
1
Pot Sticky Pads
7210-188
11
11
10mm M4 Spacers
7210-186
5
5
M4 x 14 Cap Head Screws
7210-187
5
5
Toggle Switch Dress Nut
7210-196
11
11
M3 x 8mm Stainless Panel Screws
7216-151
4
14-Pin IC Socket
7212-332
5
5
16-Pin IC Socket
7212-333
2
2
M²Synth Power Lead
7216-164
1
MOTM Front Panel
7216-591
1
Black
MOTM Back Panel
7216-891
1
MU Front and Back Panel
7219-591
1
Main PCB
7216-091
1
1
Jack Socket PCB
7215-703
1
1
Jack Socket PCB
7215-731
1
1
Jack Sockets
7216-610
1
1
Pack of 10
B100k Pots Long Shaft Angled
7216-710
1
Pack of 10
B1M Pots Long Shaft Angled
7300-830
1
B100k Pots Short Shaft Angled
7216-740
1
Pack of 10
B1M Pots Long Shaft Angled
7300-831
1
KM20B Knobs
7212-109
1
Pack of 9
MU Knobs
7219-109
1
Pack of 9
KM15B
7212-173
2
Small MU Knobs
7219-101
2

8-Step Analogue Sequencer 191 V1d 3
General Assembly Guidance
Booklet
1
1
BOM
S-7216-091-d
1
1
Circuit Schematic
S-7216-091-d
1
1
PCB Layout
S-7216-091-d
1
1

8-Step Analogue Sequencer 191 V1d 4
Assembly Instructions
The analog sequencer 191 has no particular requirements not already covered in the
‘General Guidance on a M²Synth Module Assembly’ booklet included with this kit.
Calibration
Specification
Supply voltage +/-12Vdc or +/-15V (jumpers J3 & J5 for +/-12V or J7 & J9 for +/-15V
Supply current +22mA / -17mA
Main PCB dimensions 131.95x174.05mm
Need tech support, post questions on our forum hosted by modwiggler.com