MAAX C6000 Series User manual

Regular Arm
Installation
See Page 3
Left Hand Door -LH
Righ Hand Reverse-RHR
An incorrectly installed or
improperly adjusted door closer
may cause property damage or
personal injury. These installation
instructions should be followed to
avoid the possibility of
misapplication or misadjusting.
CAUTION
CAUTION
Regular Arm
Installation
See Page 3
Top Jamb
Installation
See Page 4
Left Hand Door-LH
Right Hand Reverse-RHR
Right Hand Door-RH
Left hand Reverse-LHR
Top Jamb
Installation
See Page 4
Right Hand Door-RH
Left Hand Reverse-LHR
Parallel Arm
Installation
See pages 5 & 6
Right Hand Door-RH
Left Hand Reverse-LHR
Parallel Arm
Installation
See Pages 5 & 6
NOTE: For special applications a separate door and
frame preparation template is packed with these
instructions. This instruction sheet should be used
ONLY for installation sequence and closer
adjustments.
Doors should be hung on ball bearing or Anti-
friction hinges.
A separate door stop is recommended.
Door and frame must be properly reinforced.
Adjust closing time speed between 3 and 7
seconds from 90 to 0 . Greater closing times may
be required for elderly or handicapped.
Closer shuold NOT be installed on the exposed side (weather side) of exterior doors
Metal Wood
#7
1/4-20
3/16''
Self Drilling Screws
Wood and Metal (Optional)
Sleeve Nut and Bolt
For wood drill 3/16 hole
Drill 9/32 thru from closer side
3/8 Drill other side
Thru Bolt and Grommet Nut
Machine Screws
#7Drill.1/4-20 Tap Drill 9/32 thru from Closer Side
3/8 Drill other side
Backcheck Valve
Latch Valve
Power Adjustment Shaft
Closer Body
Sweep Valve
Regular Arm /Top
Jamb Shoe
Connecting Rod
Forearm
Screw
Main Arm
Closer Arm
Insert cutouts
Cover
Insert
Full Cover (Standard)
Parallel
Arm Bracket Screw Pack
- 1 -
Left Hand Door-LH
Right Hand Reverse-RHR
Always adjust spring power before adjusting
control.
MODEL : C6000 ADJ 1-6 INSTALLATION INSTRUCTIONS
C6000 Series Door Closer
Surface Mounted
Adjustable & Preset "Back Check"
Optional: Delayed Action (DA)
Non Hold-Open / Hold-Open

CLOSER ADJUSTMENT
Sweep
(use 1/8'' Hex wrench for these Adjustments)
Latch Backcheck
CLOSED
Backcheck
Latch
SPRING POWER ADJUSTMENT
POWER ADJUSTMENT CHART
MAXIMUM
DOOR WIDTH FULL TURNS
REQUIRED
EXTERIOR
DOORS
INTERIOR
DOORS
34''(864)
5 TURNS C.C.W.
3 TURNS C.C.W.
0 TURNS
38''(962)
30''(762)
36''(914)
42''(1067)
48''(1219)
54''(1372)
48"(1291) 60''(1542)
10 TURNS C.W.
15 TURNS C.W.
5 TURNS C.W.
- 15 Full (360 ) turns maximum available.
- Closer is factory pre-set at size.
(Use 1/8 Hex Wrench for this Adjustment)
ARM PLACEMENT
IN SHOE 7-1/2 % Stronger
or
or
7-1/2 % Weaker
- 2 -
Sweep
C6000 Series Door Closer

A5-1/2
(140)
1-3/4
(44)
1-3/16
(30)
3/4
(19)
1-3/16
(30)
12
(304.8)
E
A
B
C
D
G
90
°
L
S
(2)
or
L
S
F
Mark and Drill Holes
Parts
Covers
Optional
Right Hand Shown
Inches
(mm)
Opening Dimension A
To 100 7-1/2
(191)
*Door/Wall/Hardware/Jamb
conditions permitting
101 to 130
6
(152)
131 to*180 4-1/2
(114)
Installation Sequence
R
L
Y
S
Z
Sweep Latch
Spring power Adjust
Backcheck Pinion Cap
or Optional Cover
Caution:
Don't completely
close valve
- 3 -
1 2
3
4 5
6 7
REGULAR ARM (PULL SIDE) MOUNTING
C6000 Series Door Closer

Parts Mark and Drill Holes
12
Top of
Frame
Covers
Optional
Installation Sequence
Inches
----------------------------------
(mm)
*Door/Wall/Hardware Jamb
conditions permitting
Opening Dimension"A"
To100 7-1/2
(191)
101 to130 6
152)
131 to180 4-1/2
(114)
A longer connecting
rod is required for
reveals greater than
4"(101.6).
Reveal
Sweep Latch
Spring Power Adjust
Backcheck
Caution:
Don't completely
close valve
Pinion Cap or
Optional Cover
- 4 -
or
G
C
D
B
A
E
90
1
3
4 5
6 7
2
(304.8)
A
3/4
(19)
1/2
(13)
(140)
5-1/21-3/4
1-7/8
(38)
TOP JAMB (PUSH SIDE) MOUNTING
C6000 Series Door Closer
(44)
Right Hand Shown

2-3/4
(70)
2
(51)
3/8
(10)
A
1/2
(13)
7/16
(11)
1-1/2
F
A
B
E
D
C
G
3-1/2
(89)
3/4
(19) 12
(304.8)
B
L
S
Parts
Covers
Optional
Mark and Drill Holes
Right Hand Shown
Inches
(mm)
Door
Opening
To120
AB
9-1/2
(241)
3-3/4
(95)
*121to*180 7
(178)
1-1/4
(32)
*Door/Wall/Hardware/Jamb
conditions permitting
Installation Sequence
Close Valves
Sweep
Latch
Install Closer and Bracket Preload Closer
Top of Door
Frame
Place Arm on
Spindle
Rotate
Remove Arm
from Spindle
- 5 -
456
3
1 2
C6000 Series Door Closer
PARALLEL ARM (PULL SIDE) MOUNTING,
Part -I

B
A
L
S
S
L
1-1/2
(38
)
L
S
L
S
(2)
or
Right Hnad
Door
Flat
OR
Left Hnad
Door
Flat
Flat
R
S
Y
L
Z
Z
R
S
Y
L
Open Valves
Sweep
Latch
Caution:
Don't remove
valves
Assemble Arm
Arm Screw Spring Power Adjust Sweep
Latch Backcheck Pinion Cap
or Optional Cover
Caution:
Don't completely
close valves
- 6 -
78 9
10 11 12
13 14 15
MX-I-C6000-19
© 2019 MAAX HARDWARE INC.
C6000 Series Door Closer
PARALLEL ARM (PULL SIDE) MOUNTING,
Part -II