For Technical Assistance in the United States and Canada 1.800.421.6144. Press 2, then option 1
© Copyright 2022, C.R. Laurence Co., Inc_SDT22_22
*NOTE: Do not exceed either maximum weight or width when choosing proper quantity of hinges.
C.R. Laurence Co., Inc. •2503 E. Vernon Ave., Los Angeles, CA 90058 •1.800.421.6144 •crlaurence.com
4I-5
SENIOR PRIMA
Glass-to-Glass Hinge
CAT. NO. SRPPH02
*NOTE: Do not exceed either maximum weight or width when choosing proper quantity of hinges.
Specifications:
Glass Sizes: 1/2"(12mm) thick tempered safety glass
Construction: Solid brass
Closing Type: Self-centering when within 15° of closed position
Includes: Gaskets, screws and template
Important Information:
Template Options: The Glass-to-Glass Mount SRPPH02 Hinge offers two choices
of templates. Refer to the lower left hand corner of this page for the various
selections. The Edge Mount Template has a full leg cutout that allows a full length
vertical seal on the hinge side.
The Inset Mount Template enables the door to avoid hitting a towel bar, or some
other protrusion from the wall.
Optional Pivot Pins: Optional 5° Pivot Pins (Cat. No. SRP1VP1N) are sold as a set,
one pin for the top hinge and one pin for the bottom hinge. These 5° offset Pivot
Pins allow the installer to adjust the closing position of the door 5° inwards or
outwards. closing position of the door 5° inwards or outwards.
Use of Gaskets:
For 1/2" Glass: Use one thin gasket on one side and one thick gasket on the other side
For 12mm Glass: Use one thick gasket on both sides
Recommendations:
For public safety, we recommend the use of only tempered safety glass. Do
not use power tools when installing these hinges.
Maintenance Guidelines:
• Never use an abrasive cleaner on the hardware. Many of the components are
coated with a clear lacquer that will be irreparably damaged if subjected to
harsh, abrasive chemicals. Advise your customer that drying the hardware with
a clean, soft towel on a daily basis is the best way to maintain the hardware. If
mineral deposits build-up, mix a couple of drops of a mild liquid soap (such as
Ivory or a similar product) into a cup of warm water. Using a soft, non-abrasive
cloth, clean the hardware. Rinse thoroughly with clean, warm water and dry.
Maximum Door Capacities Two Hinges
Maximum Door Weight: 145 lbs.(66 kg)
Maximum Door Width: 36"(914mm)
C.R. LAURENCE CO., INC.
4H-1
C.R. Laurence Co., Inc.
crlaurence.com
Specifications:
Glass Sizes: 1/2"(12mm) thick tempered safety glass
Construction: Solid brass
Closing Type: Self-centering when within 15˚ of closed position
Cutout Required
Includes: Gaskets, screws and template
Use of Gaskets:
For 1/2" Glass: Use one thin gasket on one side and one thick gasket on the other side
For 12mm Glass: Use one thick gasket on both sides
Recommendations:
For public safety, we recommend the use of only tempered safety glass.
Do not use power tools when installing these hinges.
Important Information:
Template Options: The Top or Bottom Mount SRPPH01 Hinge offers two choices of templates. Refer to
the lower left hand corner of this page for the selections. The Edge Mount Template has a full leg cutout
that allows a full length vertical seal on the hinge side.
The Inset Mount Template enables the door to avoid hitting a towel bar, or some other protrusion from the wall.
Optional Pivot Pins: Optional 5˚ Pivot Pins (Cat. No. SRP1VP1N) are sold as a set, one pin for the top
hinge and one pin for the bottom hinge. These 5˚ offset Pivot Pins allow the installer to adjust the closing
position of the door 5˚ inwards or outwards.
*NOTE: Do not exceed either maximum weight or width when choosing proper quantity of hinges.
*Maximum
Door Capacities
Using 2 Hinges
145 lbs.(66 kg) 36"(914mm)
1/2" (12mm) Glass
Weight Width
Maintenance Guidelines:
• Never use an abrasive cleaner on the hardware. Many of the components are coated with a clear lacquer
that will be irreparably damaged if subjected to harsh, abrasive chemicals. Advise your customer that
drying the hardware with a clean, soft towel on a daily basis is the best way to maintain the hardware.
If mineral deposits build-up, mix a couple of drops of a mild liquid soap (such as Ivory or a similar
product) into a cup of warm water. Using a soft, non-abrasive cloth, clean the hardware. Rinse
thoroughly with clean, warm water and dry.
SENIOR PRIMA
Top or Bottom Mount Hinge
CAT. NO. SRPPH01
Edge Mount Method (9/16" (14mm) Clearance) . . . . . . . . .Page 4H-2
Inset Mount Method (9/16" (14mm) Clearance) . . . . . . . . .Page 4H-3
Refer to Dimensions Shown
to Ensure Accuracy
* SEE TEMPLATE ON BACK *
C.R. LAURENCE CO., INC.
PROFESSIONAL QUALITY
C.R. Laurence Corporate Headquarters: P.O. Box 58923 Los Angeles, CA 90058-0923; Toll Free Phone (800) 421-6144, Technical Assistance/Extension 777; Toll Free Fax (800) 587-7501
Specifications:
Glass Sizes: 1/ 2”(12mm) thick tempered safety gl ass
Constructi on: Solid brass
Closi ng Type: Sel f- centeri ng when withi n 15˚ of closed posi tion
Cutout Required Incl udes: Gasket s, scr ews and templ at e
Use of Gaskets:
For 1/2" Glass: Use one thin gasket on one si de and one thick gasket on the other side
For 12mm Glass: Use one thi ck gasket on both si des
Recommendati ons:
For publi c safety, we recommend the use of only tempered safety glass.
Do not use power tools when i nstal l i ng these hinges.
Important Informati on:
Templ ate Options: The Gl ass- to- Gl ass Mount SRPPH02 Hi nge offers t wo choi ces of templ ates. Refer
to the l ower left hand corner of this page for the vari ous sel ections. The Edge Mount Template has a ful l
leg cutout that allows a ful l length verti cal seal on the hi nge si de.
The Inset Mount Template enables the door to avoid hitting a towel bar, or some other protrusi on from
the wal l .
Opti onal Pivot Pi ns: Opt i onal 5˚ Pi vot Pi ns (Cat . No. SRP1VP1N) are sol d as a set , one pi n for the
top hi nge and one pi n for the bottom hinge. These 5˚ offset Pi vot Pi ns al l ow the instal l er to adjust the
closing positi on of the door 5˚ inwards or outwards.
4H-5
4-3/4"
(121mm)
2- 5/8"
(67mm)
2- 5/8"
(67mm)
1/8"
(3mm)
©Copyright 2001, C.R. Laurence Co., Inc.
Maintenance Gui del i nes:
• Never use an abrasi ve cl eaner on the har dware. Many of the components are coat ed wi th a cl ear l acquer
that wi l l be irreparabl y damaged if subjected to harsh, abrasi ve chemi cals. Advi se your customer that
dryi ng the hardware wi th a cl ean, soft towel on a dai l y basis i s the best way to maintai n the hardware.
If mi neral deposi ts bui l d- up, mix a coupl e of drops of a mi l d l i qui d soap (such as Ivory or a si mil ar
product) into a cup of warm water. Usi ng a soft, non- abrasive cl oth, cl ean the hardware. Rinse
thoroughly with cl ean, warm water and dry.
* NOTE: Do not exceed either maximum weight or width when choosing proper quantity of hinges.
* Maximum
Door Capacities
Using 2 Hinges
145 lbs.(66 kg) 36"(914mm)
1/2" (12mm) Glass
Weight Width
SENIOR PRIMA
Glass-to-Glass Hinge
CAT NO. SRPPH02
Edge Mount Method (1/8" (3mm) to 3/16" (5mm) Clearance) . . . . .Page 4H-6
Inset Mount Method (1/8" (3mm) to 3/16" (5mm) Clearance) . . . . .Page 4H-7
