Macrom M-DSPA.500 User manual

USER MANUAL
M-DSPA.500
DSP
POWER
AMPLIFIER
User manual_ENG_M-DSPA.500.indd 1 30/05/2018 09:27:53

Contents
Warranty ....................................................... 3
Safety information ........................................ 3
Information on disposal of unit.................... 3
Features ....................................................... 4
Specifications ............................................... 4
Product overview.......................................... 5
Front panel ............................................... 5
Speaker connectro pins layout ................ 5
How to install and connect the APP ............ 6
APP installation........................................ 6
APP overview ............................................ 6
APP overview ................................................ 7
Main .......................................................... 8
Equalizer................................................... 9
Crossover filter....................................... 10
Setting channels..................................... 11
Time alignment ...................................... 12
Selector gain level.................................. 13
Selector frequency cuts ......................... 13
Slope selector......................................... 13
Connections................................................ 14
Plug & Play ............................................. 14
Universal................................................. 14
System extension ................................... 15
Declaration of Conformity.......................... 16
User manual_ENG_M-DSPA.500.indd 2 30/05/2018 09:27:53

- 3 -
Warranty
Thank you for purchasing this Macrom product. Should your product need warranty service, please return
it to the shop where you buy it or to the Macrom distributor in your country. The warranty does not cover
damage due to improper use and or installation, incorrect connections to power supply and audio sources,
exposure to excessive humidity, unauthorized repair attempts or modifications.
Safety information
Before beginning with installation, disconnect the wire from the battery ground terminal to prevent any
short during installation.
This subwoofer must properly installed by Macrom authorized installer. Impropers installation may
damege the unit and /or the vehicle. Verify all electrical and drivability of the vehicle before the installation.
Information on disposal of unit
This product bears the selective sorting symbol for waste electrical and electronic
equipment (WEEE).
This means that this product must be handled to the local collecting points or given back to
retailer when you buy a new product, in a ratio of one to one (or one to zero if the external
dimension is less than 25 cm) pursuant to European Directive 2012/19/EC in order to be
recycled or dismantled to minimize its impact on the environment.
For further information, please contact your local or regional authorities.
Electronic products not included in the selective sorting process are potentially dangerous for the
environment and human health due to the presence of hazardous substances.
The unlawful disposal of the product carries a fine according to the legislation currently in force.
User manual_ENG_M-DSPA.500.indd 3 30/05/2018 09:27:53

- 4 -
Features
5-channel amplifier with audio processor controlled by App for smartphones and Bluetooth
streaming audio.
• 5-channel amplifier with DSP processor
• Hi-Resolution Audio streaming Bluetooth
• 4 high level inputs
• 5 amplified outputs
• 4 + 1 low level outputs (RCA)
• Bluetooth connection for regulation and control
• App dedicated for Android and iOS
• Active crossover By-pass, Low-pass, Hi-pass and Band-pass
• Time delay adjustable between 0 and 210 cm
• 7-band parametric equalizer
• Dynamic Bass adjustment
• Selector for switch-on mode (REMOTE or SIGNAL)
Specifications
M-DSPA.500 with RCA line input or high level input.
• Nominal output power
54Watt x 4 channels class AB (32W RMS)
300Watt x Class D Subwoofer (170 RMS) min 4 Ohm
• Frequency response from 20Hz to 20KH
• Noise signal ratio> 120dB
• Dynamic range> 100dB
• HD: 1KHz <0.001%
• Bluetooth 2402MHz - 2480MHz operating frequency
• EIRP 1.40dBm power
• Standby current <0.01mA
• Maximum current consumption 30A
• Operating voltage from 9Volt to 15.5Volt
• Dimensions: 195mm 130mm 38mm
User manual_ENG_M-DSPA.500.indd 4 30/05/2018 09:27:53

- 5 -
Front Panel
Product overview
Notice:
The graphic in this manual is for reference only, and may be different from the actual unit.
1. Front/Right + input
2. Front/Right - input
3. Front/Left + input
4. Front/Left - input
5. Rear/Left + input
6. Rear/Left - input
7. Rear/Right + input
8. Rear/Right - input
9. Remote output (+12V/Max 500mA)
10. Acc input
11. Rear/Right - output
12. Rear/Right + output
13. Rear/Left - output
14. Rear/Left + output
15. Front/Right - output
16. Front/Right + output
17. Front/Left - output
18. Front/Left + output
19. + Batt (12volts)
20. GND (Ground)
Speaker connector pins layout
SPEAKER
1
2345
6
7
89
19 18 17 16 15 14 13 12 11
10
Front view
SUB W FRONT REAR
LINE OUTPUT SPEAKER
R
L
1
10
20 11
SUBW OUTPUT
-+
Back view
POWER IN
GND BATT
FUSE
(30A)
POWER
PROTECT
REMOTE ON
M-DSPA.500
SIGNAL ON
POWER ON
BT ANT
1. Power mode selection switch
(REMOTE or SIGNAL)
2. Bluetooth antenna
3. LED protection indicator
4. Power LED indicator
5. Power connector
6. Fuse [30A]
7. Subwoofer output
8. Front Exit
9. Rear Output
10. Connector for loudspeakers
11. Subwoofer connector
5
78910 11
23 41 6
User manual_ENG_M-DSPA.500.indd 5 30/05/2018 09:27:53

- 6 -
How to install and connect the APP
APP installation
1. Download the APP from Google Play or Apple Store searching for “M-DSPA.500”
2. Install the application in your Android or iPhone mobile phone.
3. Activate Bluetooth on your mobile phone and search for “M-DSPA.500”, then pair it.
If necessary, the coupling code is 1234.
4. Open the “M-DSPA.500” APP and click on [ ], the amplifier will be connected and you
can set your own sound from the available functions of the APP.
5. After completing the audio settings, click (Exit) to exit the APP.
Bluetooth connection for Audio streaming
After pairing and connecting the M-DSPA.500 to your mobile phone you can associate the
BT_Audio device for playback Audio Sreaming.
1. Access the Bluetooth settings of your mobile phone.
2. Associate the device “BT_Audio_M-DSPA.500”
Now you can play the music files from your mobile phone
through the applications available on your device.
By activating playback, the Macrom DSPA.500 will play your music.
In case of an incoming call, the Macrom DSPA.500 will transfer the audio
to the your mobile phone.
User manual_ENG_M-DSPA.500.indd 6 30/05/2018 09:27:53

- 7 -
APP Installation
1. Download the APP from Google Play or Apple Store searching for “M-DSPA.500”
2. Install the application in your Android or iPhone mobile phone.
3. Activate Bluetooth on your mobile phone and search for “M-DSPA.500”, then pair it.
If necessary, the coupling code is 1234.
4. Open the “M-DSPA.500” APP and click on [ ], the amplifier will be connected and you
can set your own sound from the available functions of the APP.
5. After completing the audio settings, click (Exit) to exit the APP.
APP overview
How to install and connect the APP
Home
Front & Rear equalizer
Crossover Filter
Setting channels
Time alignment Subwoofer equalizer
User manual_ENG_M-DSPA.500.indd 7 30/05/2018 09:27:56

- 8 -
APP overview
1. Parametric equalizer; click to get the equalization functions.
2. Crossover; click to get the crossover functions.
3. Save to phone; after finishing the setting, you can create the name of the audio setting and then
with the (OK) button the audio setting will be saved in your mobile phone.
4. Connect; click to connect the amplifier from the APP.
5. Preselection of favorites; it is possible to recall the 5 presets saved in the amplifier.
6. Gain / Phase; click to get the functions of the levels.
7. Time alignment; click to get the alignment functions.
8. Save to amplifier; after finishing the setting, you can save your own audio setting in the five
presets.
9. Load preset; click to load the presets stored on the mobile device.
Main
7
4
8
9
3
2
1 6
5
User manual_ENG_M-DSPA.500.indd 8 30/05/2018 09:27:57

- 9 -
APP overview
1. 7-band equalizer adjustable from + 15dB to -15dB.
2. Dynamic Bass setting.
3. Front section selector for parameter copy
4. Front Left, equalizer setting front left section.
5. Rear Left, equalizer setting front left section.
6. Subwoofer, subwoofer section equalizer setting.
7. Variable frequency setting from 20Hz to 20,000Hz.
8. Variable Q Factor from 0.3 to 9.9.
9. Rear section selector for parameter copy
10. Front Right, equalizer setting front right section
11. Rear Right, equalizer setting right rear section
Equalizer
1
7
4
8
2
3
10
9
511
6
User manual_ENG_M-DSPA.500.indd 9 30/05/2018 09:27:57

- 10 -
APP overview
1. Overview of the graph.
2. Low cross-section frequency setting, adjustable from 20Hz to 20,000Hz.
3. Low-pass slope selector, selectable between, 6-12-18-24dB/oct or Bypass (Off).
4. Crossover selector section FL (front left).
5. Crossover selector section RL (rear left).
6. SUB crossover selector (subwoofer).
7. Setting high-pass frequencies, adjustable from 20Hz to 20,000Hz.
8. High pass slope selector, selectable between, 6-12-18-24dB/oct or Bypass (Off).
9. Crossover selector section FR (front right).
10. Crossover selector section RR (rear right).
Crossover filter
2
5
7
8
9
3
4
6
10
1
User manual_ENG_M-DSPA.500.indd 10 30/05/2018 09:27:58