MAGIC SCREED HD6060 User manual

INVENTOR
OF THE
PORTABLE
VIBRATING SCREED

PARTS BOOK & OWNER’S MANUAL

3
2
TABLE OF CONTENTS
Safety................................................................................................ p. . 3
Service, cleaning and operation........................................................ p. . 4
Assembly & starting procedure......................................................... p. . 5
Warning logos on your screed ......................................................... p. . 6
Honda engine ................................................................................... p. . 6
Magic screed assembly..................................................................... p . . 7
Parts book......................................................................................... p . . 8
p. . 9
Magic screed parts assembly............................................................ p. 10
p. 11
p. 12
p. 13
Air powered screed........................................................................... p 14
Ec declaration of conformity............................................................. p 15
MAGIC SCREED PARTS BOOK & OWNER’S MANUAL
Congratulations on your selection of Magic Screed.
Magic Screed
is manufactured for contractors and entrepreneurs in need of a
dependable, user friendly, high productivity tool to operate for leveling and smoothing
wet concrete. Any other use of this tool could damage it or even cause injuries or
death to the operator and surrounding coworkers.
Unfortunately, it is impossible to warn you about all the hazards associated with
operating or maintaining a powered screed. You must use your own good judgement.
This manual and the
Honda engine manual supplied with your Magic Screed should
always remain with the equipment. Safety instructions, assembly, maintenance and
parts lists are included.
For your own
safety , and that of your coworkers, it is required that anyone operating
or servicing the screed, read and understand the safety instruction in this manual.
Failure to do so could result in personal injury , death or equipments damage .
SAFETY
1- Read and understand the owner’s manual before operating or servicing the screed
2- Have a first aid kit available in case someone gets injured
3- Wear the appropriate safety gear (according to your local requirement)
Suggested list of protection gear
- Hardhat
- protective boots
- protective goggles
- gloves
- hearing protection
3-
Carbon monoxide hazard: Exhaust gas contains poisonous carbon monoxide. Avoid
inhalation of exhaust gas. Never run the engine in a closed or confined area without
proper ventilation
4-
Burns from hot parts: Let the engine and exhaust system cool before touching.
5- Do not put your hands on any vibrating of moving parts.
6- Refuelling: refuel with care. Gasoline is extremely flammable, and gasoline vapor can
explode. Refuel outdoors, in a well-ventilated area, with the engine stopped. Never smoke
near gasoline, and keep flames and sparks away. Always store gasoline in an approved
container. If any fuel is spilled, make sure the area is dry before starting the engine.
Use unleaded gasoline with a pump octane rating of 86 or higher.
Transporting: if the engine has been running, allow it to cool off for at least 15 minutes
before loading the screed on a transport vehicule. A hot engine and exhaust system
can burn or can ignite some materials.

5
4
2
4
4
3
15
6
#17
12
3
4
5
6
7
Handles
for
models:
HD 6060
HD 6161
SERVICE, CLEANING AND OPERATION
HONDA ENGINES:
Refer to your Honda owner’s manual.
1. Before cleaning, servicing or repairing your screed, stop the engine and wait for
any moving parts to stop then remove the spark plug cap.
If the engine has been running, allow it to cool off for at least 15 to 20 minutes
before cleaning with water.
2.Grease: the housing weight must be greased approximately every ten hours
of operation. Do not over grease. An over flow (1) is located at the
opposite side of the grease fitting (2) and must be cleaned before each greasing
to prevent pressure from being applied by the grease on the bearing. Any such
pressure could seize the bearing or damage your housing weight.
3. Your screed should be disassembled frequently for proper cleaning in order to
prevent any concrete build-up that could break or prematurely damage your
equipment. Warranty does not cover damage or performance problems on your
screed resulting from neglected maintenance or cleaning.
4. Take apart the blade and clean any concrete accumulation.
5. Take apart the housing weight from the handles and clean the concrete
underneath the handles and in the housing shaft.
6. Take the rubber cover off and clean any concrete or grease accumulation to
allow the counterweight to move freely.
7. Put everything back together making sure that the plastic spacers are between
the blade and the housing weight. Tighten the blade following the assembly
procedure to 85 to 100 Lb.-Ft. torque it is very important that the plastic
spacers are always between the vibrator and the blade.
MAGIC SCREED ASSEMBLY & STARTING PROCEDURE
1- Take the protective foam out of
the box.
2- Remove both adjustable handles and the
base handle (assembled with
vibrator and housing shaft).
3- Insert the adjustable handles
into the base handle (throttle
control on the right side) and
tighten the collar. Do not
overtighten.
Note: If ordered with 360
0
adjustable handles, adjust
and tighten to comfort.
4-Stand
Place the stand with the flat
side against the support, ensuring
that one of the nylon washers
is on each side of the stand
(follow the drawing).
5- Assembly of the engine
Remove the engine from
the protective foam.Place
the engine on the housing
shaft, make sure that
the driveshaft is inserted
in the clutch adaptor, and
tighten. (Do not overtighten)
(See drawing).
6- Put the rounded end of the throttle
cable into the throttle control and
adjust so that the rubber handle
grip becomes the stopper.
7- Assembly of the blade
Assemble the blade (1) on the screed vibrator (2)
in the following order: bolts (3), washers (4),
blade (1), plastic spacers (5), washers (4), nuts (6).
(See drawing).Tighten all the above at approximately
85 to 100 Lbs. torque. It is very important
that the plastic spacers are always between the
vibrator and the blade. They are used as a cushion
and prevent blade damage. If both are not in place,
this could void the warranty. Replacement plastic
spacers are available at your Magic Screed dealer.
grease fitting (2)over flow (1)

7
6
Honda
Model HD 6060, HD 6161, HD 7070, HD 7171 with
Honda engine
Before starting your Honda engine, consult the Honda ownerʼs manual
supplied with your screed.Keep this manual handy.
Notes:
- The Honda engine on your screed is a 4-cycle engine. It requires unleaded
gasoline. Consult your
Honda ownerʼs manual , page 8.
- The on/off switch is located on the left-hand side, under the carburator
of the engine supplied with your screed.
-
Warning: there is no oil in the engine. To check oil level, consult the
Honda ownerʼs manual, page 9.
The complete starting procedure is in your Honda ownerʼs manual, pages 4.
on/off switch
HONDA ENGINE
Warning logos on your screed
Logo, explanation and label positioning:
HOT
➟
➟
STOP ENGINE BEFORE RE-FUELING
UNLEADED GAZ ONLY
WARNING !
WARNING : USE WITH CAUTION
EYE
PROTECTION GLOVES BOOTS
MAGIC SCREED
630 RUE DE L’ARGON
Québec, (Québec)
CANADA, G2N 2J6
MODEL HD 7070
YEAR 2013
ENGINE HONDA
35CC GX 35 TMS3
ENGINE ASSY.
MASS 13.70 KG
RPM 8500
KW 1.1 KW
1- Description label; left handle 2- Hot label; near exhaust system
3- Appropriate safety gear;
left handle
4- Stop engine before refuelling;
Gas tank
BLADES
FITS ON ALL POWER UNITS
FT M #
4' 1.22 2050
6' 1.80 2051
8' 2.44 2052
10' 3.00 2053
12' 3.66 2054
14' 4.27 2055
16' 4.88 2056
*Other sizes available...
MAGIC SCREED POWER UNITS
HD 6060 HONDA ENGINE WITH
ADJUSTABLE HANDLES
ON HEIGHT ONLY
HD 6161 HONDA ENGINE WITH
ADJUSTABLE HANDLES ON
HEIGHT ONLY AND EXTRA
VIBRO MOUNTS
HD 7070 HONDA ENGINE WITH
ADJUSTABLE HANDLES
ON 360°
HD 7171 HONDA ENGINE WITH
ADJUSTABLE HANDLES ON
360° AND EXTRA VIBRO MOUNTS
Table of handling information
Weight & length of different components and assembly
BLADES 2050 2051 2052 2053 2054 2055 2056
LENGTH Feet Meter Feet Meter Feet Meter Feet Meter Feet Meter Feet Meter Feet Meter
4 1,22 6 1,8 8 2,44 10 3 12 3,66 14 4,27 16 4,88
WEIGHT LB KG LB KG LB KG LB KG LB KG LB KG LB KG
6.7 3 10.1 4.6 13.4 6.1 16.8 7.63 20.2 9.16 23.5 10.68 26.9 11.77

89
HONDA
25
17
18
26
28
31
33
32
12
35
11
12
11
12
2
15
7
24
3
13
4
14
6
30
(XTRA VIBO)
34 48
39
45 44 47 46
37-2
37-3
37-1
27
27
38
6
36
29
5
50
12
52
51
12
38
51
53 54
55
20
20
19
21
56
21
36
57
8
7
1
10
10 9
MODEL MODEL MODEL MODEL
QTY HD6060 QTY HD6161 QTY HD7070 QTY HD7171
1 PLASTIC SPACER 2 10002 2 10002 2 10002 2 10002
2 VIBRO MOUNT 2 10003 2 10003
3 SEAL 1 10005 1 10005 1 10005 1 10005
4 GREASE FITTING 1 10008 1 10008 1 10008 1 10008
5 RUBBER COVER 1 10009-2 1 10009-2 1 10009-2 1 10009-2
6 HANDLES 1 50004 1 50004 1 50004 1 50004
6 HANDLE HOLD STYLE 1 10011-2 1 10011-2 1 10011-2 1 10011-2
7 HOUSING WEIGHT 1 50003 1 50003 1 50003 1 50003
8 BOLT 1/2 2 10017 2 10017 2 10017 2 10017
9 NUT 1/2 2 10018 2 10018 2 10018 2 10018
10 WASHER 1/2 4 10019 4 10019 4 10019 4 10019
11 WASHER 8 MM 4 10023 4 10023 4 10023 4 10023
12 NUT 8 MM 16 10024 16 10024 16 10024 16 10024
13 SHAFT ASSY 1 10026 1 10026 1 10026 1 10026
14 COUNTER WEIGHT 1 10027 1 10027 1 10027 1 10027
15 XTRA VIBRO MOUNT 2 10003 2 10003
17 HOUSING SHAFT 1 50001-2 1 50001-2 1 50001-2 1 50001-2
18 DRIVE SHAFT 1 20003-5050 1 20003-5050 1 20003-5050 1 20003-5050
19 CIRCLIP 13 MM 1 20004 1 20004 1 20004 1 20004
*20 BEARING 2 20005 2 20005 2 20005 2 20005
*21 CIRCLIP 29 MM 2 20006 2 20006 2 20006 2 20006
24 DRIVE AXLE 1 20009 1 20009 1 20009 1 20009
25 THROTTLE CONTROL 1 20010 1 20010 1 20010 1 20010
26 THROTTLE CABLE 1 20011 1 20011 1 20011 1 20011
27 GRIP 2 20012 2 20012 2 20012 2 20012
28 STAND 1 20013-1 1 20013-1 1 20013-1 1 20013-1
29 STAND RUBBER 1 20014 1 20014 1 20014 1 20014
30 CIRCLE 1 1/2 1 20016 1 20016 1 20016 1 20016
31 BOLT 1/4 1 200171 1 200171 1 200171 1 200171
32 NUT 1/4 1 20018 1 20018 1 20018 1 20018
33 6 MM NYLON FOR STAND 2 20023 2 20023 2 20023 2 20023
34 THROTTLE CABLE CLIP 1 20024 1 20024 1 20024 1 20024
35 TIE RAP 1 20026 1 20026 1 20026 1 20026
36 POP 1/8 FOR STAND RUBBER 2 20027 2 20027 2 20027 2 20027
37-1 ADJ. HDL. GRIP SECTION 2 20032-2 2 20032-2
37-2 ADJ. HDL. LONG SECTION 2 20032-3 2 20032-3
37-3 TOP SECTION HANDLES 2 20032-4 2 20032-4
38 CLIP FOR HANDLES 2 20033 2 20033 4 20033 4 20033
39 HONDA ENG. GX 35 TSM3 1 50000 1 50000 1 50000 1 50000
44 ON OFF SWITCH HONDA 1 40005 1 40005 1 40005 1 40005
45 SWITCH BRACKET HONDA 1 40006 1 40006 1 40006 1 40006
46 BOLT FOR 40006 1 40007 1 40007 1 40007 1 40007
47 LOCK FOR 40008 1 40008 1 40008 1 40008 1 40008
48 BOLT FOR 20024 HONDA 1 40010 1 40010 1 40010 1 40010
50 TIE RAP 1 20040 1 20040 1 20040 1 20040
51 CAP FOR 50002 8 50005 8 50005 8 50005 8 50005
52 ANTI VIBRATION SEAL 1 50002 1 50002 1 50002 1 50002
53 ENGINE ADAPTOR 1 50006 1 50006 1 50006 1 50006
54 BOLT M6 1 40002 1 40002 1 40002 1 40002
55 LOCK M6 1 40004 1 40004 1 40004 1 40004
56 HOUSING SHAFT SEAL 1 50008 1 50008 1 50008 1 50008
*57 RUBBER TUBE 1 50009 1 50009 1 50009 1 50009
*Please refer to the note attached to this manual.
MAGIC SCREED PARTS BOOK 2004 - HONDA
DESCRIPTION

10
DA 4050 THROTTLE CABLE ASSEMBLY STANDARD
PART NUMBER QTY DESCRIPTION
20011 1 THROTTLE CABLE
20010 1 THROTTLE CONTROL
20026 1 TIE RAP
DA 4051 THROTTLE CABLE ASSEMBLY LONG
PART NUMBER QTY DESCRIPTION
20011-L 1 THROTTLE CABLE LONG
20010 1 THROTTLE CONTROL
20026 1 TIE RAP
DA 4055 RUBBER COVER ASSEMBLY
PART NUMBER QTY DESCRIPTION
10009-2 1 RUBBER COVER
20040 1 TIE RAP
DA 4057 GRIP ASSEMBLY
PART NUMBER QTY DESCRIPTION
20012 1 GRIP SET OF 2
DA 4059 VIBRO MOUNTS
PART NUMBER QTY DESCRIPTION
10003 2 VIBRO MOUNTS
10024 8 NUT 8 MM
10023 4 WASHER 8 MM
DA 4059-X X-TRA VIBRO MOUNTS
PART NUMBER QTY DESCRIPTION
11003 2 X-TRA VIBRO MOUNTS
10024 8 NUT 8 MM
10023 4 WASHER 8 MM
DA 4061 BOLT & NUT 1/2
PART NUMBER QTY DESCRIPTION
10018 2 NUT 1/2
10017 2 BOLT 1/2
10019 4 WASHER 1/2
10002 2 PLASTIC SPACER
DA 4064 BEARING FOR DRIVE SHAFT
PART NUMBER QTY DESCRIPTION
20005 2 BEARING
20004 1 CIRCLIP 13 MM
20006 2 CIRCLIP 29 MM
50009 1 HOUSING SHAFT SEAL
MAGIC SCREED PARTS ASSEMBLY MAGIC SCREED PARTS ASSEMBLY
11
DA 4067 BEARING FOR HOUSING WEIGHT
PART NUMBER QTY DESCRIPTION
10026 1 SHAFT ASSY
20016 1 SNAP RING 38 MM
10005 1 SEAL
10008 1 GREASE FITTING
DA 4070 SECONDARY LIFTING HANDLE (HD 4040 HD 5050)
PART NUMBER QTY DESCRIPTION
20036 1 SECONDARY LIFTING HANDLE
DA 4073 ENGINE ADAPTOR GX 31
PART NUMBER QTY DESCRIPTION
40001 1 ENGINE ADAPTOR GX 31
40003 1 SNAP RING
40002 1 BOLT FOR 40001
40004 1 LOCK FOT 40002
DA 4077 DRIVE AXLE
PART NUMBER QTY DESCRIPTION
20009 1 DRIVE AXLE
DA 4080 DRIVE SHAFT ASSEMBLY HONDA
PART NUMBER QTY DESCRIPTION
20003-5050 1 DRIVE SHAFT HONDA
20005 2 BEARING
20006 2 SNAP RING 29 MM
20004 1 SNAP RING 13 MM
50009 1 HOUSING SHAFT SEAL

12
DA 4091 THROTTLE CABLE SHORT
PART NUMBER QTY DESCRIPTION
20011 1 THROTTLE CABLE
W./ ADJUSTEMENT
DA 4095 THROTTLE CABLE FOR ADJ. HANDLE BAG OF 10
PART NUMBER QTY DESCRIPTION
20011-L 10 THROTTLE CABLE LONG
W./ ADJUSTEMENT
DA 4096 THROTTLE CABLE SHORT BAG OF 10
PART NUMBER QTY DESCRIPTION
20011 10 THROTTLE CABLE
W./ ADJUSTEMENT
DA 4097 ALLEN 6 MM 5 MM
PART NUMBER QTY DESCRIPTION
10056 1 ALLEN 6 MM 5 MM
DA 4098 TIE RAP FOR 10009-2
PART NUMBER QTY DESCRIPTION
20040 10 TIE RAP
DA 4099
PART NUMBER QTY DESCRIPTION
20026 10 TIE RAP FOR HANDLES
DA 4100
PART NUMBER QTY DESCRIPTION
50002 1 ANTI VIBRATION SEAL
10024 8 NUT 8 MM
DA 4101
PART NUMBER QTY DESCRIPTION
50005 8 CAP FOR 8 MM NUT
13
DA 4102 HOUSING WEIGHT ASSEMBLY
PART NUMBER QTY DESCRIPTION
10002 2 PLASTIC SPACER
10005 1 SEAL
10008 1 GREASE FITTING
10009-2 1 RUBBER COVER
10017 2 BOLT 1/2 NF X 1” 3/4
10018 2 NUT 1/2 NF
10019 4 WASHER 1/2
10026 1 SHAFT ASSEMBLY
10027 1 COUNTER WEIGHT
20016 1 CIRCLIP 38 MM
20040 1 TIE RAP HOUSING WEIGHT
50003 1 HOUSING WEIGHT
* DA 4103-2 HOUSING SHAFT ASSEMBLY
PART NUMBER QTY DESCRIPTION
20003-5050 1 DRIVE SHAFT FOR HD-5050
20004 1 CIRCLIP 13 MM
20005 2 BEARING
20006 2 CIRCLIP 29 MM
50001-2 1 HOUSING SHAFT
50008 1 HOUSING SHAFT SEAL
*Please refer to the note attached to this manual.
MAGIC SCREED PARTS ASSEMBLY MAGIC SCREED PARTS ASSEMBLY
DA 4088 STAND ASSEMBLY
PART NUMBER QTY DESCRIPTION
20013-1 1 STAND
20018 1 NYLON NUT 1/4
20023 2 NYLON WASHER 1/4
20017 1 BOLT 1/4
20014 1 STAND RUBBER
20027 2 RIVET
50009 1 RUBBER TUBE
DA 4090 THROTTLE CABLE FOR ADJ. HANDLE
PART NUMBER QTY DESCRIPTION
20011-L 1 THROTTLE CABLE LONG
W./ ADJUSTEMENT

15
14
AIR SCREED PARTS
RR-1015 VIBRATOR ASSEMBLY
RR-1016 VIBRATOR REDUCING FITTING
RR-1018 HANDLE BOLT & NUT
RR-1019 TEE CONNECTOR FITTING
RR-1020 AIR HANDLE MAIN SECTION
RR-1020-1 AIR HANDLE ASSEMBLY
RR-1021 AIR VALVE ASSEMBLY
20012 RUBBER HANDLE (SET OF TWO)
RR-1023 AIR HANDLE EXTENTION 5 "
RR-1032 HANDLE L.H.
RR-1045 AIR MANIFOLD ASSEMBLY
RR-1070 1/4 HOSE FITTING
RR-1222 PNEUMATIC HOSE 3/8 (BY THE FEET)
RR-1222-M PNEUMATIC HOSE 3/8 (BY METER)
RR-1072 BOLT 1/2 NF X 2 1/2
(USE 10018 & 10019)
RR-1073 1/4 PLUG
AIR POWERED SCREED
M FT # BLADES VIBRATOR
1.22 4' R3 1011 2
1.80 6' R2-6 1009 2
2.44 8' R2 1010 3
3.00 10' R4 1012 4
3.66 12' R5 1013 5
* Must use a 25 cfm air compressor at 100 psi
DECLARATION OF CONFORMITY
MAGIC SCREED INC.
DECLARES THAT THE EQUIPEMENT
TYPE:
Vibrating screed for leveling concrete
MODEL: Magic Screed HD6060 - HD 6161
HD7070 - HD7171
E-Screed HDE-1010
SERIAL NUMBER :
IS IN ACCORDANCE WITH THE FOLLOWING DIRECTIONS:
2006/42/EC, 2004/108/EC
HAS BEEN MANUFACTURED ACCORDING TO THE FOLLOWING STANDARDS:
BS EN 12649 : 2008 + A1 : 2011.
EN 12100-1 : 2003, EN12100-2 : 2003
Magic screed, 630 rue de l’Argon, Québec, Qc, Canada, G2N 2J6
TEL : [phone] www.magicscreed.com
By : Benoit Rouillard

4795 rue Louis-B.-Mayer
Laval, Quebec
Canada H7P 6G5
Sales Office
Tel.: [phone]
Fax: [phone]
Plant
Tel.: [phone]
Fax: [phone]
Visit our Web site:
www.magicscreed.com
E-Mail:
[email protected]
REV 04-2013
To keep with your parts book
For all HD7070, HD7171, HD6060, HD6161
●Improvement have been applied to the
housing shaft of your Magic Screed.
●A new seal has been added to prevent water
that was coming down in the housing shaft
while cleaning the engine.
●Please take note and refer at those
part numbers when it will be time to
service your Magic Screed.
NOTE

DRIVE SHAFT 20003-5050
CIRCLIP 29 mm 20006
BEARING (X2) 20005
CIRCLIP 29 mm 20006
HOUSING SHAFT 50001-2
SEAL 50008
CUTAWAY VIEW OF THE HOUSING SHAFT

●The Drive shaft # 20003-5050 is now modified so it can
be used with the new seal. It still fits any Magic Screed
equipped with GX 35 Honda Engines.
●Replacement housing shaft will come with the seal
and circlip already installed.
●Part # DA 4103 Housing shaft assy. is also discontinued
and it’s replaced by #DA4103-2
Visual identification of the new parts
Housing Shaft
50001-2
Punched with a #2
Previous Disc.
New