Magicfx CO2 Dominator Operating manual

CO2 SWITCH.
USER AND INSTALLATION MANUAL
CO2 FX PART02472 rev 01-00
ENGLISH

DISCLAIMER
WARNING Read this manual carefully before installing and/or using this
product. Failure to read the manual and to follow the printed
instructions may lead to personal injury and/or damage to the
product.
© 2023 MAGICFX®
All rights reserved.
Nothing from this publication may be copied, reproduced and/or published by
means of printing, photocopying or by any other means, without the prior written
approval of MAGIC FX.

TRADEMARKS
Any brand names mentioned in this manual are registered trademarks of their
respective owners.
LIABILITY
MAGIC FX accepts no liability for claims from third parties arising from unauthorised
use, use other than that stated in this manual, and use other than in accordance with
the General Conditions registered at the Chamber of Commerce.
We further refer to the General Conditions. These are available on request, free of
charge.
Although considerable care has been taken to ensure a correct and comprehensive
description of all relevant components, the manual may nonetheless contain errors
and inaccuracies.
Should you detect any errors or inaccuracies in the manual, we would be grateful if
you would inform us. This helps us to further improve our documentation.
2 MAGICFX®ECO2JET —User and Installation Manual

MAGICFX®ECO2JET —User and Installation Manual 3
TABLE OF CONTENTS
Disclaimer 2
Trademarks 2
Liability 2
Introduction 4
Revision table 4
1 MEET THE MAGICFX®CO2 SWITCH! 5
1.1 Main parts 5
1.2 Technical data 6
  
1.4 Accessories 7
2 Safety 8
2.1 General safety rules 8
2.2 CO 
2.3 Indoor use 9
2.4 Rigging 9
2.5 Noise Levels 9
2.6 Safety symbols 10
2.7 Safety precautions 10
3 Installation and use 11
3.1 Mount on a SUPERBLASTER II 11
3.2 Connect Power 12
3.3 Connect CO 
3.4 Blast with power 15
3.5 Clean up 15
4 Maintenance 18
5 Troubleshooting 18
6 Correct disposal 18
7 EC Declaration of Conformity 19

INTRODUCTION
This manual contains all information required for the intended use of the equipment.
Deviation from the described intended use can result in a hazardous situation and/or
property damage.
This manual includes notes and warnings on safe operation of the equipment. These
notes and warnings are accompanied by the following icons. Read them attentively!
DANGER Indicates a hazardous situation that, if not avoided, will result in
death or serious injury. This signal word is to be limited to the most
extreme situations.
WARNING Indicates a hazardous situation that, if not avoided, could result
in death or serious injury.
CAUTION Indicates a hazardous situation that, if not avoided, could result
in minor or moderate injury.
NOTICE Indicates information considered important, but not hazard-
related (e.g. messages relating to property damage).
LANGUAGE
This document contains the original instructions in English. In case you require other
languages please contact MAGIC FX.
REVISION TABLE
Doc nr Revision Date Description Author Approved
PART02472 01-00 04-09-2023 Initial release MBO PvdW
4 MAGICFX®ECO2JET —User and Installation Manual

MAGICFX®ECO2JET —User and Installation Manual 5
1 MEET THE MAGICFX®CO2 SWITCH!
The MAGICFX®CO2 SWITCH enables controlling a SUPERBLASTER II with power. The
CO2 SWITCH can be controlled with a commander or a switchpack.
The MAGICFX®CO2 SWITCH is equipped with several holes for mounting the unit. The
CO2 SWITCH can be mounted to a stage or to a truss with a truss clamp. Safety
cables can be attached,
The MAGICFX®CO2 SWITCH is suited for simultaneous activation of multiple units
through a power link.
1.1 MAIN PARTS
M10 MOUNTING
HOLE
SUPERBLASTER II
MOUNTING
CO2OUT QUICK
CONNECTOR
CO2IN QUICK
CONNECTOR
POWER IN AND OUT
WITH LED INDICATOR
Main parts

6 MAGICFX®ECO2JET —User and Installation Manual
1.2 TECHNICAL DATA
Product Product Name CO2 SWITCH
Product Code MFX1124
Product Type CO2 FX
Main
Dimensions
Length 203 mm 7.3 in
Width 140 mm 4.5 in
Height 155 mm 6.1 in
Weight Weight 3.7 kg 8.2 lb
Package Length 280 mm 11.4 in
Width 200 mm 11.4 in
Height 180 mm 7.9 in
Packaged weight 4.2 kg 9.3 lb
Environment Minimum Temperature -20 °C -4 °F
Maximum Temperature 70 °C 158 °F
Humidity (Relative) 20 % to 90 % (non condensing)
Electrical Voltage Input 220 – 240 Vac
Voltage Frequency 50 Hz / 60 Hz
Power Consumption: 12 W
Power Connector Neutrik®powerCON TRUE1 (in & out)
Controlling Control Options Direct output
Usage Propellant Liquid CO2
Propellant Connector CO2Quick Connector 3/8 “
Propellant Consumption 0.5 L/s
Technical data
1.3 PRODUCT IDENTIFICATION
Type plate

MAGICFX®ECO2JET —User and Installation Manual 7
1.4 ACCESSORIES
Code Product Included
MFX1114 
MFX1105 
MFX1106  3 M
MFX1108  10 M
MFX1109 
MFX1110 
MFX1103 
MFX1115 
MFX1121 CO2High Pressure Hose 3/8 Male - Female, 5 m
MFX1122 
MFX3103 Twenty Clamp (20 kg) M10
SPR00119 Safety Steel
MFX0313 Schuko to Neutrik® powerCON TRUE1 - cable 1.5 m
MFX0313Accessories

8 MAGICFX®ECO2JET —User and Installation Manual
2 SAFETY
The CO2 SWITCH has been designed and constructed in such a manner that it can
be used safely. This applies to the use, the circumstances and the regulations as
described in this documentation. Reading this documentation and following the
instructions are therefore necessary for everyone who is authorised to work with the
CO2 SWITCH.
The CO2 SWITCH must be used in surroundings that:
• Have a stable temperature of between -20 and 70 °C.
• Have a relative humidity degree between 20 % and 90 % (non condensing).
• Are free of dust, corrosive gases and high concentrations of organic vapours.
• Are not situated in the vicinity of a source of vibration.
2.1 GENERAL SAFETY RULES
• Only authorised persons may carry out work with the CO2 SWITCH.
• Do not use the CO2 SWITCH if there are people or animals in the direct output.
• Make sure that children, unauthorised people and animals do not obtain
access to the CO2 SWITCH.
• Do not connect more units to a single electrical circuit than the installed fuse
is able to handle. (Calculate the summed load with the electrical data from
Chapter 1)
• Do not remove any safeguards, safety caps and safety symbols.
• All required safety devices must be in good condition and function properly.
• 
• Keep the workplace clean.
2.2 CO
The MAGICFX® CO2 SWITCH uses liquid COas input. The application of COinvolves
serious risks. Make sure that you are well informed on these risks before installation
and/or operation. Always use approved COcylinders, hoses and connections.
Always consult your COsupplier for regulations and instructions on safe installation
and use.
MAGIC FX is not liable for unsafe situations, accidents and damage that are the result
of incorrect working with COand COcylinders.
WARNING Inadequate installation and/or operation of a COpowered
machine and COcylinders can lead to death or serious injury.
Always follow the instructions from this manual, from your CO
supplier and from local authorities.

MAGICFX®ECO2JET —User and Installation Manual 9
2.3 INDOOR USE
The CO2 SWITCH is designed for outdoor use and use in well-ventilated indoor
spaces. When used indoors, make sure you take the necessary preparations. These
preparations could include, but are not limited to:
• Consulting your COsupplier.
• Calculating the reduction of oxygen for the indoor space.
• Checking the location for spots where COcould accumulate and taking
preventive actions.
• Installing COmonitoring devices that will warn for hazardous COlevels.
WARNING Do not use the MAGICFX® CO2 SWITCH in poor ventilated
 can cause
symptoms like headache, nausea, loss of consciousness or even
death.
2.4 RIGGING
Please follow the European and national guidelines for safe rigging and trussing.
2.5 NOISE LEVELS
The emitted noise levels are dependent on the machine the CO2 SWITCH is
connected to.
WARNING Do not operate the CO2 SWITCH close to yourself or to others for
a long period of time. If you experience any hearing loss or
ringing in the ears, you should immediately stop using the unit.

10 MAGICFX®ECO2JET —User and Installation Manual
2.6 SAFETY SYMBOLS
Symbol Meaning Position
Read the manual carefully before use! Control panel.
Safety symbols
2.7 SAFETY PRECAUTIONS
WARNING Using a damaged or an improper installed machine can lead to
death, serious injury or property damage. Always inspect the
machine thoroughly before operation.
WARNING A poorly mounted machine will come loose when the machine
blasts CO2. This can lead to death, serious injury and/or property

correctly as according to the instructions in this manual.
WARNING Missing or obscured safety symbols on the machine can lead to
death, serious injury or property damage. Make sure all safety
symbols are correctly in place and visible, see Section 2.5.

MAGICFX®ECO2JET —User and Installation Manual 11
3 INSTALLATION AND USE
3.1 MOUNT ON A SUPERBLASTER II
1 Loosen the starknob by turning it counter-clockwise.
2 Mount the CO2 SWITCH on the desired position on the SUPERBLASTER II.

12 MAGICFX®ECO2JET —User and Installation Manual
3 Tighten the starknob to secure the CO2 SWITCH.
3.2 CONNECT POWER
1 Connect the PowerCon TRUE1 power cable to the power input of the CO2
SWITCH. Connect the other end to the power controller with a 100-250 Vac (50-60
Hz) power output source.
CAUTION Do not connect more units to a single electrical circuit than the
installed fuse is able to handle. (Calculate the summed load with
the electrical data from Chapter 1)
2 Switch the power on and check if the LED power indicator lights up. Check if
you hear a clicking sound. If so, then the machine is working correctly.
CAUTION Make sure that the COis not connected when testing the power.
3 

MAGICFX®ECO2JET —User and Installation Manual 13
3.3 CONNECT CO
1 
2 Connect the COhose to the COconnector on the SUPERBLASTER II and the
other end to the CO2 SWITCH.
3  cylinder.

14 MAGICFX®ECO2JET —User and Installation Manual
4 Connect the COhose to the CObottle to hose connector on the COcylinder.
5 Connect the other end of the COhose to the CO2 SWITCH.
6 In case of multiple machines: Repeat steps 1 – 5 for each machine.

MAGICFX®ECO2JET —User and Installation Manual 15
3.4 BLAST WITH POWER
WARNING Carefully read the manual of the SUPERBLASTER II for all safety
steps.
1 Open the COcylinder.
2 When it’s time to shoot, switch the power on.
CAUTION Do not use the machine if the COvalve is not opening and
closing correctly.

16 MAGICFX®ECO2JET —User and Installation Manual
3.5 CLEAN UP
1 Close the COcylinder.
2 Switch the power on to release the remaining pressure.
3 

MAGICFX®ECO2JET —User and Installation Manual 17
4 Disconnect the CO
cylinder.
5 
6 Dismount the machine.

18 MAGICFX®ECO2JET —User and Installation Manual
4 MAINTENANCE
To achieve the maximum service life of the CO2 SWITCH you must regularly clean the
CO2 SWITCH and test if it is functioning correctly.
Contact MAGIC FX if the CO2 SWITCH is not functioning correctly.
DANGER Do not replace parts yourself; always consult MAGIC FX.
5 TROUBLESHOOTING
Always contact MAGIC FX if any malfunctions or errors occur that cannot be solved
with the instructions as described in this manual.
6 CORRECT DISPOSAL
This symbol on the product and / or accompanying documents
means that used electrical and electronic products should not be
mixed with general household waste. For proper treatment,
recovery and recycling, please take this product to designated
collection points where it will be accepted free of charge.
Alternatively, in some countries you may be able to return your
products to your local retailer upon purchase of an equivalent new
product.
Disposing of this product correctly will help save valuable resources and prevent any

otherwise arise from inappropriate waste handling.
Please contact your local authority for further details of your nearest designated
collection point.
Penalties may be applicable for incorrect disposal of this waste, in accordance with
your national legislation.

MAGICFX®ECO2JET —User and Installation Manual 19
7 EC DECLARATION OF CONFORMITY











WWW.MAGICFX.EU