Magnavox MCR41808 User manual

Use AC power adapter
1. Using the Supplied Power adaptor and take the power cable pin to insert to the back of
the device “DC IN”.
2. Plug in the power adaptor to the wall plug or electric shocket.
3. Please be caution at all time that this Power Adaptor supports only 5V, 1.5A DC current.
4. Unplug the power adaptor at all time if not in use.
Install battery
1. This device has a battery compartment in use of 2 x AAA battery (not included) to
support RTC, Real Time Clock.
2.To replace the battery, simply open the battery compartment door at the back of the
device and insert the batteries carefully in accordance with the Positive “+” and negative
“-“position.
3.The device is able to detect at low-battery status, if so, a LED light will blink, and a new
set of batteries are required for replacement.
PLESAE BE ADVISED THAT, this back up battery is mainly for support in case of power
outage, the clock to work in order.

Control Buttons
①。Power ( On/ Off) ②。Mode
③。Volume Down ④。Volume Up
⑤。Pervious / Adjust Hour/ Radio Scan Up ⑥。Play/ PAUSE/ SAVE Radio Channel
⑦。Next / Adjust Min / Radio Scan Down ⑧。Alarm Clock Set up
⑨。Sleep Mode ⑩。PAUSE / Snooze(Brightness)
⑪。Clock Set up ⑫。Bluetooth Pair
⑬。Wireless Charging Pad

⑭。USB Port （For USB drive music play back）
⑮。AUX IN
⑯。DC IN
⑰。FM Antenna cable
LED Display
①。Radio ②。Bluetooth
③。USB mode ④。AUX IN
⑤。Alarm ⑥。After-noon
⑦。Time

Clock Set Up
Plug in power adapter, when the device is on for the first time, the clock shall display
12:00 and blink.
Long press the " " clock button when the display is on or flashing display, and
press “ " key to set hours, press " " key to set minutes.
Press " "again."" the clock key is set when time is stored and completed.
Brightness Set Up
•When the device is on Stand-by mode, the brightness on the display can be adjusted
at three different stages.
•Press “Snooze” button to tune in High, Medium and Low.
Radio
There are two methods to tune radio
Method 1: AUTO Search Mode
1. Press “Play &Pause” for auto search. All channels will be saved as P01, P02,
P03… until the search is done.
2. Press “Previous” and “Next” to change Channels.
Method 2: Manual Radio Search
1. Press & Hold “Previous” : search will be conducted downwards.
2. Press & hold “NEXT” : search will be conducted upwards.
3. On Manual search mode, searching will stop on every channel is being found.
Improve radio reception
Move around the FM antenna to get the best position for reception.

Keep all digital audio player and mobile phones away from FM antenna at all time to
minimize the disturbance.
Alarm Clock Set Up
This Alarm Clock supports two alarming sound,” Pre-set Alarm sound or Radio”.
1. Power on the device that is on Stand-by mode, Press and hold “Alarm” button,
the display will blink, and alarm indication light will flash.
2. Press “Previous” button to set HOUR and Press “next” button to adjust
Mins. Press “alarm” key to confirm and save.
To change alarming sound, press “Previous” or “NEXT” buttons to
change.
The display shows “bu2” as pre-set sound and “rAd” for radio. Press “alarm” to
display alarm volume and press “previous” and ‘next” to adjust volume.
3. On Alarm mode, press “Snooze” to set up pause in mins, on loop in
sequence, 10, 20,30,40,50,60mins.
4. On clock mode, press “Snooze” to check the remaining alarm time.
Remark:
NO brightness adjustment is allowed when the device on alarm sound mode.
Sleep timer Set Up
You are able to choose Music Playback and Radio for sleep timer to end the working
mode.
1. Press “Sleep” to set sleep timer. The timer has pre-set for 15, 30, 60, 90mins
and it loops to OFF timer after 90mins.
The clock display will return 3 seconds after the sleep timer mode is OFF.

Remark:
•Sleep timer mode, Press “Sleep” button to check the remaining time.
•Press “Sleep Mode” button to choose and set for the timer.
AUX IN Set Up
1. Power ON the device
2. Press “Mode” to change the status to AUX IN. Check the display is on AUX
mode.
3. Insert the audio cable (not included) to the LINE IN，the device can play external
audio files.
Bluetooth Mode
1. Power on the Device
2. Press “Mode” button twice to make sure the device working mode on display
is on BT mode. Press “PAIR” button for Bluetooth pairing.
3. Once is connected, the Bluetooth LED light will be on.
4. Press and hold “PAIR”button to end the paired device and return to pairing
mode.
USB Mode
1. The device is on
2. Press “MODE” button to set the device is on USB working mode as shown
on display.
Remark:
A. The device is on working mode, inserting any USB drive supporting with audio formats,
the device shall read and play automatically.
B. USB port for USB drive music play back. Please note that this USB port has 100mA
electric supply or less, does not support smart phone or any high-power capacity
charging.

Wireless Power Charging
1. Align the position to where the mobile phone can detect the wireless charging.
2. The mobile phone will automatically sense the current and display the charging status
on the mobile phone.
3. This device only supports mobile phones capable of and in accordance with the wireless
charging protocol.
Note:
If the position of mobile phone is not able to detect the transmitting coil, the mobile phone
will not be charged, similarly if the protective case is not supporting wireless charging, you
are required to remove the case and to place the mobile phone to the correct position.
SPECIFICATIONS
Adaptor Power source
AC 100-240V~, 50/60Hz, 0.35A(Max)
Output of the supplied AC/DC
Adaptor
DC 5V,1.5A
Battery Backup
2x 1.5V “AAA” size batteries
Speaker
4 ohms
Output Power
2W
Frequency Range (FM)
87.5 - 108 MHz
Bluetooth Version
V4.2，33 feet (10m)
USB Port
Support up to 32GB, (not included) for MP3 Playback
Wireless Power Charging Rating
5V , 1A，5W
Accessories:
1 x Instruction booklet
1 x AC/DC Adaptor