Magnavox RG15AE User manual

CR188-RG15A(B)
16117000000934
REMOTE CONTROL MANUAL
MAGNAVOX and SMART. VERY SMART are registered
trademarks of Koninklijke Philips N.V. and are used under
license from Koninklijke Philips N.V.

1
2
3
4
5
Using the remote control ..............................................................
Remote control specifications......................................................
Button functionality .................. ....................................................
How to use the buttons .................................................................
Auto mode................................................................................................................
Cooling/Fan mode...................................................................................................
Dehumidifying mode ..............................................................................................
Sleep mode...............................................................................................................
Timer ........................................................................................................................
Energy saving mode ...............................................................................................
CONTENTS
Use the remote control within 16.4 foot range
from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.
Range of the remote control
16.4ft
CAUTIONS
The air conditioner will not operate if curtains, doors or other materials block
the signals from the remote control to the AC unit.
Prevent any liquid from interfering into the remote control. Do not expose the
remote control to direct sunlight or heat.
If the infrared signal receiver on the AC unit is exposed to direct sunlight,
the air conditioner may not function properly. Use curtains to prevent the
sunlight from interfering on the receiver.
If other electrical appliances react to the remote control, either move these
appliances or consult your local dealer.
Using the remote control
2
Sleep
C
Fh
ilete
crk
Fo
M
lleow
Auto
On/off
Fan High
Med
Low
E
S
n
a
e
v
regry
on off
Timer
Auto
Fan
Cool
Dry
Mode
TEMP/TIMER
TEMP/TIMER
Heat
5
5
6
6
7
Installation instructions of battery
Step 1: Insert a coin vertically in the groove
on the battery cover, clockwise rotation of 45
degrees, make sure that the groove is aligned
with the "unlock" sign as shown below
and remove the battery cover.
Step 2: Install battery inside the remote
control, the positive (+) side up.
Step 3: Install the battery cover, make
sure the battery cover groove is aligned
with the "unlock" sign. Insert a coin
vertically in the groove and press it
gently, then counter clockwise rotation
of 45 degrees, make sure the groove is
aligned with the "lock" sign as shown
below.
9
Coin
Battery cover
Groove
Lock sign
Unlock sign
Groove
Unlock sign
Battery cover
Battery Positive (+) side up
Coin
Groove
Battery cover
Unlock sign
Lock sign Coin
Groove
Battery cover
Unlock sign
Lock sign
Lock sign
Coin
WARNING
1. Battery must be disposed properly. Do not short
circuit or dispose in the fire.
2. Keep batteries out of the reach of children.
3. Caution for ingestion.
4. Non-rechargeable batteries are not to be
recharged.
5. Exhausted batteries are to be removed from
the product.

Button functionality
Push this button to
decrease the
temperature setting in
1 °C/1 °F increments
down to 17 °C/62 °F.
3 4
Press this button to
activate the Sleep mode.
This function is available
on COOL or AUTO mode
to maintain a comfortable
temperature.
Operation starts and stops when
the button is pressed again.
Used to select the fan
speed in four steps:
Auto, Low, Med, and
High.
ON/OFF button
MODE button
Press this button to
select the desired
operation mode from
AUT
and FAN.
O, COOL, DRY,
TEMP DOWN button
TEMP UP button
FAN button
TIMER button
Push this button to
activate the "Auto
Start" or "Auto Stop"
program.
SLEEP button
Model
Lowest Voltage of
CPU Emitting Signal
Rated Voltage
RG15A(B)/E,
。 。 O O
-5 C 60 C(23 F~140 F)
16.4ft
3.0V
2.4V
( Dry batteries Lr03x2)
~
Remote Control Specifications
Environment
Signal Receiving Range
ONE TOUCH button
Push this button, the
system will automatically
shift to COOL operation
with auto fan speed, the
setting temperature is
O O
26 C/80 F. And the timer
setting program will be
cancelled. (on some models)
NOTE: If the unit has ENERGY
SAVER function, it w i ll i ni ti a t e
automatically the Energy Saver
function under Cool, Dry, and
Auto (only Auto-Cooling and
Auto-Fan) modes.
NOTE:
-Buttons design is based on typical model and might be slightly different
from the actual one you purchased, the actual shape shall prevail.
-When there are wide differences between “Remote Control Illustration” and
“USER'S MANUAL” on function description, the description on “USER'S
MANUAL” shall prevail.
ENERGY SAVER button
Push this button to
increase the temper-
o O
ature setting in 1 C/1 F
increments up to 30 °C/86 °F
Press this button to
activate the Energy-
saving mode. Press
it again to stop the
function. (only on some
models)
RG15A1(B)/E,RG15A2(B)/E,RG15A3(B)/E,
RG15A(B)/E RG15A1(B)/E RG15A2(B)/E RG15A3(B)/E
NOTE: On some models
SWING replaces ONE TOUCH.
Push SWING button,
the vertical louvers will
swing automatically from
side to side. Press it again
to deactivate the "SWING"
feature. (only on some models)
( )

5 6
Dehumidifying mode(only on
some models)
In the Dehumidifying mode, you cannot switch the
fan speed. It is automatically controlled in this mode.
NOTE
Ensure the unit is plugged in and power is
available.
1. Press the ON/OFF button to start the air
conditioner.
2. Press the MODE button to select Dry.
3. Press the TEMP UP/DOWN button to
set the desired temperature. The temp-
erature can be set within a range of
o O o O o O
17 C/62 F~ 30 C/86 F in 1 C/1 F
increments.
Cooling/Fan mode
Ensure the unit is plugged in and power is
available.
1. Press the ON/OFF button to start the air
conditioner.
2. Press the MODE button to select Cool, or
3. Press the TEMP UP/DOWN button to set the
desired temperature. The temperature can
o O
be set within a range of 17 C/62 F~
o O o O
30 C/86 F in 1 C/1 F increments.
4. Press the FAN button to select the fan
speed in four steps- Auto,Low, Med,or High.
mode.Fan
In the Fan mode, the setting temperature is not
displayed in the remote control and you are not
able to control the room temperature either. In this
case, only step 1, 2 and 4 may be performed.
NOTE
How to use the buttons
Auto mode
Ensure the unit is plugged in and power is
available.
1. Press the ON/OFF button to start the air
conditioner.
2. Press the MODE button to select Auto.
3. Press the TEMP UP/DOWN button to set
the desired temperature. The temperature
o O
can be set within a range of 17 C/62 F~
o O o O
30 C/86 F in 1 C/1 F increments.
3
4
2
1. In Auto mode, the air conditioner will automatically
select the Cooling or Fan mode depending on the
difference between the actual room temperature
and the desired set temperature on the remote
control.
2. In Auto mode, the fan speed is controlled
automatically.
3. If the Auto mode is not comfortable for you , the
desired mode can be selected manually.
NOTE
1
3
1
Sleep mode
Press this button to activate the Sleep
mode. This function is available on COOL
or AUTO mode only and maintain the
most comfortable temperature for you.
In this mode the selected temperature will
O O
increase by 1 C/2 F 30 minutes after the
mode is selected. The temperature will
O O
then increase by another 1 C/2 F after an
additional 30 minutes. This new temperature
will be maintained for 6 hours before it
returns to the originally selected temperature.
This ends the Sleep mode and the unit will
continue to operate as originally programmed.
The Sleep mode program can be cancelled
when press the MODE, ON/OFF, FAN SPEED
and SLEEP button during operation.
3
2
1
3
3
2
1
3

78
Timer
Press the TIMER button can initiate the
Auto-start and Auto-stop setting program
of the unit. The time can be set in range
of 0~24 hours.
To set the Auto-start/stop time.
1. Press the TIMER button, when the TIMER
ON indicator displayed on the LED window
of the air conditioner, it indicates the Auto
Start setting program is initiated. When the
TIMER OFF indicator displayed on the LED
window of the air conditioner, it indicates the
Auto Stop setting program is initiated.
2. Press or hold the UP( ) or DOWN( ) to
change the Auto time by 0.5 hour increments,
up to 10 hours, then at 1 hour increments up
to 24 hours. The control will count down the
time remaining until start/stop.
3. The selected time will register in 5 seconds
and the air conditioner will automatically
revert back to the previous temperature
setting.
4. Turning the unit ON or OFF at any time
will cancel the Auto Start/Stop function.
NOTE: To cancel the TIMER setting, push
the TIMER button and press or hold the UP
( ) or DOWN( ) until 0 hour is displayed
on the LED window of the air conditioner.
2
1
2
To stop the air conditioner 2 hours after setting
and start it again 10 hours after setting.
1. Press the TIMER button until the TIMER
OFF indicator is displayed on the LED display
of the air conditioner.
2. Use the UP/DOWN button to display "2.0" on
the LED display of the air conditioner.
3. Press the TIMER button again to display the
TIMER OFF on the LED display of the unit.
4. Use the UP/DOWN button to display "10" on
the LED display of the unit.
5. Wait for 5 seconds until the previous display
revert back to the LED window.
AUTO STOP →AUTO START
(On →Stop →Start operation)
This feature is useful when you want to program
the AC to automatically STOP and then START.
Example:
COMBINED TIMER
(S both ON and OFF )etting timers simultaneously
Example:
AUTO START→ATUO STOP
(Off →Start →Stop operation)
This feature is useful when you want to program
the AC to automatically START and then STOP.
To start the air conditioner 5 hours after setting,
and stop it 8 hours after setting.
1. Press the TIMER button until the TIMER
ON indicator is displayed on the LED display
of the air conditioner.
2. Use the UP/DOWN button to display
"5.0" on the LED display of the air conditioner.
3. Press the TIMER button again to display
the TIMER OFF on the LED display of the unit.
4. Use the UP/DOWN button to display
"8.0" on the LED display of the unit.
5. Wait for 5 seconds until the previous display
revert back to the LED window.
2
1
2
+ -
+ -

9 10
1
NOTE:
-The device could comply with the local national regulations. In Canada,
it should comply with CAN ICES-3(B)/NMB-3(B). In USA, this device
complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interfe-
rence, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
-This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for
compliance could void user s authority to operate the equipment.
Energy saving mode
In this mode, the fan will continue to
run for 3 minutes after the compressor
shuts off. The fan then cycles on for 2
minutes at 10 minute intervals until the
room temperature is above the set
temperature, at which time the compre-
ssor turns back on and cooling starts.