Magnavox MHT828 User manual

1
Before using the unit, be sure to read all operating
instructions carefully. Please note that these are general
precautions and may not pertain to your unit For example,
this unit may not have the capability to be connected to an
outdoor antenna.
1. Read these instructions
All the safety and operating instructions should be read
before the product is operated.
2. Keep these instructions
The sately and operating instructions should be retained
for future reference.

2

6.5V1.8A
INSTALLATION
POWER SOURCE
Insert the small plug from the supplied AC/DC Adaptor to the DC IN Jack
on the rear of unit. Connect the AC/DC Adaptor to a wall outlet having AC
100-240V~, 50/60Hz .
1. Main Unit
2. Remote Sensor
3. Supplied Screws (For Base Assembly)
4. Speakers with Decorave LED Lights
5. Wooden Base
6. Control Buons (On the top)
7. Decorave LED Lights
NOTE: This AC/DC Adaptor is intended to be correctly orientated
in a vercal or floor mount posion.

ASSEMBLING METHOD
Assembling Method:
Assembly the two wooden bases to the boom of unit by the supplied assembly screws and screwdriver as the figure above.

Assembly the two wooden bases to the boom of unit by the supplied assembly screws and screwdriver as the figure above.
LOCATION OF CONTROLS
1. ANT (FM Antenna)
2. POWER ON/OFF Switch
3. DC IN Jack
4. AUX IN 1 Jack
5. AUX IN 2 Jacks
6. (Standby On/Off) Buon
7. Indicators
8. LED 2 Buon
9. SOURCE/LED 1 Buon
10. VOL - (Volume Down) Buon
11. VOL + (Volume Up) Buon
12. TUNE-/ Buon
13. TUNE+/ Buon
Top View:
Rear View:

1. (Standby On/Off) Buon
2. LED ON/OFF Buon
3. (Mute) Buon
4. SOURCE Buon
5. RESET Buon
6. TUNE-/ Buon
7. (Play/Pause) Buon
8. TUNE +/ Buon
9. VOL (Volume) +/- Buons
10. TREBLE +/- Buons
11. BASS +/- Buons
LOCATION OF CONTROLS (REMOTE CONTROL)

BUTTON CELL (REMOTE CONTROL)
-First me use:
Remove and discard the insulaon film as the figure on right.
-Replacing the buon cell for the remote control if it is drained.
1. Push and slide out the baery tray as the figure below.
2. Replace the buon cell by a new CR2025 buon cell with the polarity “+” face up as the figure below and
the makings on the rear of remote control.
3. Close the baery tary.
BATTERY PRECAUTIONS
Follow these precauons when using a baery in this device:
1. Use only the size and type of baery specified.
2. Be sure to the follow the correct polarity when installing the baery as indicated in the baery
compartment. A reversed baery may cause damage to the device.
3. Do not mix different types of baeries together(e.g. Alkaline and Carbon-zinc) or old baeries with
fresh ones.
4. If the baeries in the device are consumed or the device is not to be used for a long period of
me, remove the baeries to prevent damage or injury from possible baery leakage.
5. Do not try to recharge the baery not intended to be recharged; it can overheat and rupture.
(Follow baery manufacturer’s instrucons.)
6. The baeries shall not be exposed to excessive heat such as sunshine, fire or the like.
7. Clean the baery contacts and also those of the device prior to baery installaon.
8. This product contains a coin/buon cell baery. If the coin/buon cell baery is swallowed.
It can cause severe internal burn in just 2 hours and can lead to death. Keep new and used
baeries away from children. If the baery compartment does not close securely, stop using the
product and keep it from children. If you think baeries might have been swallowed
EFFECTIVE DISTANCE OF REMOTE TRANSMITTER
NOTES:
When there is an bostacle between the unit and
the transmier, the transmier may not operate.
When direct sunlight, an incandescent lamp,
fluorescent lamp or any other strong light
shines on the REMOTE SENSOR of the unit, the unit
remote operaon may be unstable.

GENERAL OPERATION:
1. Connect the supplied AC/DC Adaptor to the unit and wall outlet as previously instructed.
2. Slide the Power ON/OFF Switch on the rear of unit to turn the unit on to standby mode.
3. Press and hold the Buon on the top of unit or press the Buon on the Remote Control to
turn the unit ON from standby mode. The corresponding indicator will illuminate.
4. Press the SOURCE -- LED 1 Buon on the unit or SOURCE Buon on the Remote Control repeatedly
to switch to desired source. The color of the indicator will switch to the corresponding
source (see list below):
Playback Mode: Color of Indicators:
BT (Bluetooth) Blue (and blinking)
FM Radio Purple
AUX 1 Green
AUX 2 Orange
5. During playback,
Press the VOL (Volume) +/- Buons on the unit or Remote Control to adjust volume as desired.
Press the TREBLE +/- Buons on the Remote Control to adjust the treble (high audio frequency)
as desired.
Press the BASS +/- Buons on the Remote Control to adjust the bass (low audio frequency) as
desired.
Press the (MUTE) Buon on the Remote Control to turn off the sound temporarily, press again to
turn it back on.
Press and hold the SOURCE/LED 1 Buon on the top of unit to power On/Off all the Decorave
LED Lights.
Press the LED 2 Buon on the top of unit to power On/Off the central Decorave LED Lights.
Press the LED ON/OFF Buon on the Remote Control repeatedly to turn the Decorave LED Lights on
the speaker and/or central on/off as desired.
6. When finished, press and hold the Buon on the unit or press the Buon on the Remote Control
to turn the unit to standby mode. The color of the Indicator will turn to red.
7. If unit is not used for a long period of me, power off the unit by slide the POWER ON/OFF Switch on
the rear of unit to OFF posion.
(For saving energy, unplug the AC/DC Adaptor from wall outlet).
BT (BLUETOOTH):
OPERATION
Listen music from external BT device:
BT (Bluetooth) pairing:
First me use or re-pairing the unit to a new BT Device, pair as follows:
1. Power on the unit as previously instructed.
2. Press the SOURCE – LED 1 Buon on the top of unit or the SOURCE Buon on the Remote Control
3. Power on the external BT Device and enter to BT searching mode. Start pairing following the on screen
4. If pairing is complete you may now play music with your external BT Device.
5. During playback:
Notes:
instrucons from the external BT Device. When paired, the blue Indicator will stop blinking.
repeatedly unl the color of Indicator turn to blue and blink.
Press the Buon on the unit or Buon on the Remote Control to pause, press again to resume
normal playback.
Press the TUNE -/ or TUNE +/ Buons on the unit or Remote Control repeatedly to skip tracks.
When the external BT Device searches for the unit, our model number “MHT828” will appear on the
display of external BT Device.
If while pairing you are asked for a code please try "0000" or "1234".

Normal operaon aer pairing:
1. Turn on the BT funcon of the external BT Device.
2. Power on the unit and enter to BT mode as previously instructed. The color of the Indicator will turn blue
and blink.
3. Wait a few seconds unl the unit is automacally paired to the external BT Device. (The blue Indicator will
stop blinking).
4. Aer pairing is complete you may now play music with your external BT Device.
FM Radio:
1. Power on the unit as previously instructed.
2. Press the SOURCE – LED 1 Buon on the top of unit or the SOURCE Buon on the Remote Control repeatedly
unl the color of Indicator turn to Purple.
3. Press and hold the TUNE-/ or TUNE +/ Buons on the unit or Remote Control to auto search and play
the previous/next available radio staons.
4. Repeat the same procedure unl the desired staon are found.
5. If you want search for the staons from beginning, press the RESET Buon on the Remote Control then
search the Radio staons again as point 3 above.
Antennas:
This unit has a FM wire antenna on the rear of unit, which provides adequate recepon in most areas. If recepon is weak,
unwind and extend to its full length or reassemble the other direcon/locaon to improve recepon.
AUX 1:
Listen to music from external Audio Player through AUX 1 IN Jack:
1. Insert one of the plug from supplied Audio Connecon Cable to the Phones Jack; Line Out Jack or AUX Out Jack
on the external Audio Player such like the iPhones; iPad; iPod; MP3 Player; Discman … etc.
2. Insert the other plug to the AUX 1 IN Jack on the rear of unit as the shown below:
3. Power on the unit as the instructed earlier.
4. Press the SOURCE/LED 1 Buon on the unit or press the SOURCE Buon on the Remote Control repeatedly unl
the color of the Indicator turn to Green.
5. Play the music on the connected external Audio Player as usual. (Make sure the volume level of the external
Audio Player is in high level. Otherwise, sound from this unit may weak).
AUX 2:
Listen music from external Audio Player through AUX 2 IN Jack:
1. Insert one end of RCA Connecon Cable (not included) to the RCA audio jacks the external Video/Audio Player
such like the TV; DVD Player; Video Recorder … etc.
6.5V 1.8A
6.5V1.8A

6.5V1.8A
GENERAL SPECIFICATIONS
Power Source: ..........................................
Power Source of Remote Control:
FM Radio Coverage: ....................................
Imredance of Speakers: .............................
...............
Audio Power: ............................................
DC 5V, 2.5A
DC 3V, 1 x CR 2025 buon cell (incleded)
FM 87.5 -108 MHz
2 Ohms, 8 W x 2
5 W x per channel (Total 10 W, RMS)
PACKAGE INCLUDES:
SPECIFICATIONS AND ACCESSORIES ARE SUBJECT TO CHANGE WITHOUT NOTICE
1 x Remote Control ( Uses 1 x CR 2025 buon cell, induded )
1 x Audio Connecon Cable with 3.5mm Stereo plugs
1 x AC/DC Adaptor (Input: AC 100-240V , 50/60Hz, 0.4A Max. Output DC 5V, 2.5A )
1 x Owner's Manual
2 x Wooden Bases
6 x Assembly Screws (For Wooden Bases Assembly)
1 x Screwdriver
2. Insert the other end to the AUX 2 IN Jacks on the rear of unit as the shown below:
3. Power on the unit as the instructed earlier.
4. Press the SOURCE/LED 1 Buon on the unit or press the SOURCE Buon on the Remote Control repeatedly
unl the color of the Indicator turn to Orange.
5. Play the music on the connected external Video/Audio Player as usual. (Make sure the volume level of the
external Video/Audio Player is in high level. Otherwise, sound from this unit may be weak).