Magnum MCR-35 Specification sheet

Product instruction manual
Magnum® MCR-35, MCR-46 Creasing System
Magnum Creasers have been designed to be user friendly,
however we strongly recommend you take a few minutes
to read through this manual to ensure correct operation.
Keep this manual safe for future reference.

2
Page 2 - Specications
Page 3 - Introduction
Page 4 - Safety Instructions
Page 5 - Information before use
Page 6 - Operating the creaser
Page 7 - Warranty and incorrect use
Contents
Specications
MCR35 MCR46
Max. Width (mm) 350 460
Maximum Thickness (gsm) 350 350
Creasing Depth (mm) 0.4 0.4
Creasing Length (mm) 600 600
Creasing Width (mm) 1.3 1.3
Overall Dimensions (mm) 600x385x125 600x495x125
Gross Machine Weight (Kg) 8.8 11
Warranty 1 year 1 year

3
Thank you for purchasing the Magnum Creasing System.
The Magnum range of creasing systems are robust, reliable and hard-working.
Please read these instructions carefully before starting to use the system to ensure you get
the best results and are competent at operation.
Should you experience any problems please contact your supplier.
Introduction

4
Safety Instructions
• Do not place any objects on this system.
• Do not let hairs, a necktie or necklace hang over the system. Doing so may cause an injury.
• Do not put the system on an unstable place such as a shaky stand or a slanted oor. Doing so may
cause the system to drop or fall down, causing an injury.
• Do not put the system in a moist or dusty place.

5
Information Before Use
1. Precautions on Installation
Do not install it in an unstable place such as on a faltering bench or an inclined place.
It may fall down or drop and cause an injury.
Do not install it in a dusty place or a place of high humidity.
Do not install it in a place exposed to direct sunlight.
Avoid a location near a window.
Do not install it in a location close to heating equipment.
Do not install it in a place exposed to a direct wind.
2. Components of the Magnum Creaser
1
2
3
4
5
6
7
8
1 - Fixed position vernier
2 - Vernier rail
3 - Moving position vernier
4 - Vernier lock
5 - Position ruler
6 - Operation platform
7 - Creasing handle
8 - Mechanism core protection cover

6
Operating the creaser
One operator is required when the machine is working.
Please do not push the handle with force, this could cause injury and damage to the system.
• Make sure the position and size of the document you are creasing is correct and accurate.
• If only one crease is needed, x the position of the right positioning vernier according to the creasing
size.
• If two creases are needed, i.e a book spine. Move the right positioning vernier to the necessary position
and x, then move the left positioning vernier to the correct position and x accordingly to the creasing
size and position.
When moving the positioning verniers, please hold its head up and move the model parallel. Please do not
move with its head as this could cause damage to the system.
When moving the positioning verniers to the dierent positions please secure with the screws manually.
• When the positioning vernier is xed in its position, place the creasing document against the mechanism
core protection cover and the xed position vernier.
• If only one crease is needed move the paper rightwards and place against the xed right side positioning
vernier. Push the operation handle downward then release and remove the document.
• If two creases are needed move the paper rightwards rst and place the document against the xed right
hand side positioning vernier. Push the operation handle downward then release it and then move the
paper leftwards, place it against the left side positioning vernier. Push the operation handle downwards,
release and remove the document.

7
Warranty & Incorrect Use
IMPORTANT INFORMATION
Your Magnum Creasing System should reach you in perfect condition, however please retain all of the original packaging once
you have unpacked your Creasing System in case you need to return it for repair. If your system arrives damaged or faulty in
anyway, this must be reported to your supplier immediately. If the Creasing System is sent back for repair under warranty and
is damaged in transit due to faulty packaging your warranty may be void.
The Creasing System you have purchased includes a 1 year warranty on defective parts and general wear and tear, it does not
cover any damage through misuse or operator error.
E&O.E