Magpowr PS90 Manual

222 W. Memorial Road, Oklahoma City, OK 73126-0508
Phone: [phone] Fax: [phone]
www.magpowr.com E-mail: m[email protected]om
INSTRUCTION MANUAL
MODEL PS90
90 VDC POWER SUPPLY
All of the information herein is the exclusive proprietary property of Maxcess International, and is disclosed with the
understanding that it will be retained in confidence and will neither be duplicated nor copied in whole or in part nor
be used for any purpose other than for which disclosed.
Copyright 2004, all rights reserved.
Periodically there will be updates to this manual. The latest version is available at www.magpowr.com or by calling
1-800-MAGPOWR (624-7697).
1.0 Introduction
The MAGPOWR Model PS90 is an isolated controllable current regulator for 90 vdc magnetic particle clutches and
brakes. The PS90 also provides a small amount of reverse current to minimize the drag torque of the clutch / brake.
The Model PS90 has four jumper selectable current ranges. Maximum outputs for the individual ranges are 0.125,
0.25, 0.5 and 1.0 adc. The appropriate range is determined by the current rating of the clutch or brake to be
controlled. For best torque control resolution, the lowest current range providing sufficient current for maximum
operating torque should be selected.
The PS90 accepts either a remote adjustment potentiometer, or a 0 to 10 vdc analog control signal.
Connections are provided for an external 1 madc current meter. The meter display will indicate output current as a
percentage of the output range selected.
The control circuits are electrically isolated from the power circuits.
2.0 Installation
The PS90 is intended for installation on a vertical panel with a DIN 35 rail, with the wiring terminals facing down.
Figure 1 shows the enclosure dimensions.
Figure 1
Enclosure Dimensions
850A264-1
10/04 Rev. C
6.18 [157.0 mm]2.30 [58.4 mm]
1.39 [35.2 mm] 3.38 [85.9 mm]

2
REMOTE POTENTIOMETER
1K TO 10K
L1
OUTPUT METER
L2 +-
90V 1mA
POTENTIOMETER
or 0-10V INPUT
SHIELD +-
1234567 23
VAC
115
CW
-+
24 25 26
ALLOWED IN
(OPTIONAL)
CLUTCH/
BRAKE
METER
REMOTE
0-1 mA DC
D.C. OUTPUT
115 VAC
50/60 Hz
SWITCH NOT
71
JP1
Wiring to and from the PS90 must be done with double or reinforced insulation or protective screening which
provides protective separation. All wiring should comply with the essential requirements of the appropriate
standard(s) and is the responsibility of the installer.
Route AC power away from control signal wiring. Connect shields of shielded cable to the terminals indicated as
“SHIELD”. Maximum shield length and maximum length of wires outside of the shield is 3 in. (75 mm).
3.0 Setup
Remove the enclosure top by inserting a flat blade screwdriver under the retaining tabs in the base (See figure 2).
Set the JP1 current range selection jumpers to the range appropriate for the clutch / brake connected to the PS90
(See figure 3 for current range settings). The factory setting is 1/8 amp range. Replace the enclosure top.
Figure 2 Figure 3
Enclosure Top Removal JP1 Current Range Settings
4.0 Electrical Connections
Figure 4 shows the connections that are required for the basic system. They are:
115 vac power
90 vdc output for clutch / brake
1 to 10 kohm Potentiometer
Route AC power away from control wiring. The clutch / brake wires and the remote meter wires should be twisted
pair. Run the signal input wiring in shielded cable. Connect the shield to the provided terminal marked “SHIELD”.
The maximum shield length and maximum length of wires outside of the shield is 3 in. (75 mm).
When using a 0-10 vdc input instead of a potentiometer, connect the negative of the input to terminal 26 and the
positive of the input to terminal 25.
The 90 vdc output and the remote meter output are not isolated from the AC line and must not be ground
referenced. The potentiometer input is isolated and may be ground referenced.
Figure 4
Electrical Connections for PS90

3
5.0 Maintenance
The only maintenance that may be required on the PS90 is fuse replacement. Replacement of the fuse(s) requires
first removing ac power, then opening the enclosure. The enclosure must be re-installed to maintain the IP rating.
The enclosure may be opened by inserting a flat blade screwdriver under the retaining tabs in the base (See figure
2).
6.0 Troubleshooting
Symptom Possible Cause Solution or Diagnostic
No AC power. Verify incoming power is correct
voltage and frequency.
Fuses blown. Clutch / brake wires shorted together
or shorted to ground.
Clutch / brake wires open
circuit.
Disconnect clutch / brake wires at the
PS90 and check for proper
clutch / brake resistance between the
wires.
No clutch / brake
output.
Remote potentiometer or
external power supply not wired
correctly, or shorted together.
Voltage between terminal 24 and 26
should be 10 vdc.
Voltage between terminal 25 and 26
should vary from 0 to 10 vdc as the
potentiometer or external 0 to10 vdc
power supply is moved through its
range of travel.
Incorrect type of meter. Meter should be a current meter with
1 ma full scale and no more than
3 kohm resistance.
Remote meter not
working.
Meter wires shorted or open. Disconnect meter wiring at the PS90
and check for proper meter resistance
between the wires.
7.0 Options
The PS90 is factory adjusted to provide full reverse current with 0 vdc input. If some other current is desired with 0
vdc input or the minimum remote potentiometer setting, the minimum current potentiometer may be adjusted by
cutting out the hole shown on the label and then using a trimpot adjustment tool. Modifying this setting will cause
the clutch / brake drag torque to be higher than expected and is not recommended.

8.0 Specifications
Supply Voltage: 115 vac, +/- 10%, 50/60 Hz, 1.1 amp maximum, sinusoidal
Fuses: F1, F2 1.6 amp, Littelfuse Part No. 21601.6, or
Wickmann Part No. 19194-053-FS
Enclosure: IP20
Climatic Class: 3K3 (EN60721)
Temperature Range:
Operating: 0° C to 50° C
Storage: -30° C to 80° C
Relative Humidity: 5% to 85%
Pollution Degree: 2 (IEC664-1)
Altitude: 0 to 2000 m
Compatible Residual Current
Device Types: A or B (IEC755)
Worst Case Fault Current: 1.6 amp
Inputs:
Signal Potentiometer: 1 to 10 kohm, ¼ watt minimum
or
Voltage: 0 to 10 vdc, 100 kohm input impedance
Outputs:
Clutch / Brake
Voltage: -3 to 90 vdc, full wave, phase controlled
Current: Adjustable in four ranges:
-0.004 to 0.125 madc
-0.008 to 0.25 madc
-0.016 to 0.5 madc
-0.032 to 1.0 madc
Regulation: < 1% of range
Current Drift: 0.024 %/° C
Meter Signal: 0 to 1 madc, +/-2% into 3 kohm maximum
Potentiometer Supply Voltage: 10 vdc +/-2%, 10 madc maximum